Use the same Kconfig infrastructure and options for all SPI drivers.
Jira: ZEP-294
Change-Id: I7097bf3d2e1040fcec166761a9342bff707de4dd
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Avoids confusion with .gitignore rules, which were inadequate to
cover all the places where these files are found. At least in
VIM, these files are now syntax highlighted correctly.
Change-Id: I23810b0ed34129320cc2760e19ed1a610afe039e
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Instead of defining the output format in the toolchain environment
setup, define this per SoC that supports the ABI.
This will allow us to directly referencing an installed toolchain
without the need for declaring ZEPHYR_GCC_VARIANT
Change-Id: Icd1a7a21acbf075a51854fb2ebb3ef06788ce9b5
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
QMSI defines all the registers of the SoC and other values in
qm_soc_regs.h, so cleanup soc.h and rely on the data from the BSP
contained in qm_soc_regs.h.
Change-Id: I672925cf1c0144a9ed64073ea289c691285a8082
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Fix naming and use a global driver name for instance.
Change-Id: I30a54cb9c20773e1b6fdc57b934aa564612a6c45
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Quark flash sub-driver. It is based on the QMSI driver.
In order to enable this driver, the following options
must be set.
CONFIG_QMSI_DRIVERS
CONFIG_QMSI_INSTALL_PATH
CONFIG_FLASH
CONFIG_SOC_FLASH_QMSI
Origin: Original
Change-Id: Iffbea3b17624c755e367677b76d7216c2fba2ca1
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Remove UART default configuration to make it default UART_0. This
makes default working fine with Nordic BLE chip using H:4 driver.
Change-Id: Icb6d9f068b586bbf04694bc77ed968211de94c8a
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ib7e0b81b2df1a0225fc244fea3035416d0a4f282
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
This also separates IRQ_PRI into one for DW and one
for QMSI, to follow the convention of every other
drivers.
Change-Id: I338f819f71c18fa9e17015e8a588a3d0207350c6
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ic73783189db57059d2b7f3727e4802e1b2e27931
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ifdbb5e3a997795ef577350d88f8cb06877eb6463
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This patch extends the i2c shim driver so it supports the 'default
configuration' infrastructure which enables the user to specify a
default configuration for the I2C device. The default configuration
is set during driver initialization.
This patch also changes Quark SE and D2000 Kconfig.defconfig files so
the i2c default configuration is set to '0x12' which means standard
bus speed, 7-bit addressing and master mode. This is the same value
used when DW driver is selected, by the way.
Change-Id: I06e0dc3c29e8da2f3317db5bef285177f2e92c9a
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Remove those kconfig options that are SoC specific, and should not be
configurable via kconfig.
Change-Id: Ia62888838877da4627419bd36c261d5254761acd
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
These interrupt settings are SOC specific. So, move them to the
SOC level of Kconfig.
As IRQ priority is fixed in D2000, changed the value to 0 to
make it consistent with what other shim drivers are using.
Change-Id: Id20bed46c478a7555ae976e3a3063ba2cb099788
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This is hardware design so there is no need for it to be
configurable in kconfig.
Change-Id: Iff162f330aae8ef9a7139b6e7ed9bfa87f26189a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The IRQ triggering condition should be specified by SoC as it is
a decision for hardware design. This should not be configurable
in kconfig.
The default is to be triggered on rising edge, just as the same
old kconfig did.
Change-Id: If59d88a30711eb8e03d9cc4f409055cefe1995c5
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Moves those kconfig options which should be declared in
SoC or board header files instead. These are the one
that are tied to SoC or board and there is no need
for them to be configurable in kconfig.
Change-Id: I243d634f1a4a11dc8dc3530d95f93371015492b7
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This is to standardize the kconfig for specifying IRQ priority.
Change-Id: Iab10655c6fc6f17c0c6dd49cb7a4e74fabcf852c
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This is to standardize the kconfig for specifying IRQ priority.
Change-Id: I3a51b35e633dc7b1b841e9fa504bf0cfc0d4d575
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Most of the SoC and board Kconfig use the same values for
driver initialization priorities. So refactor them, and
discard duplicate ones.
The shared IRQ init priority was changed so that the kernel
default init and device init priorities can be standardized
across all SoC/boards. Same goes for DesignWare SPI driver.
This also changes the UART_CONSOLE_PRIORITY and
IPM_CONSOLE_PRIORITY to UART_CONSOLE_INIT_PRIORITY and
IPM_CONSOLE_INIT_PRIORITY, to standardize across all drivers.
Note that this does not take away the ability to override
those values. This just provides reasonable defaults such
that there is virtually no need to override.
Change-Id: Ibbd95d802c637df06f9a2fd48763ee1e6f4ff627
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The pinmux base address and number of pins are now defined in SoC or board
header files instead of specifying them in kconfig. This is because
the pinmux ties directly to the SoC (or board expanders) so the base
address and number of pins do not need to be configurable in kconfig.
Change-Id: Ib6090d7d022b491f3fe8f522858281504c6302bb
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds conditions to the default values for device init priorities,
and make them follow the dependencies on the config options. This cleans
up the resulting .config a bit, making it easier to read.
Change-Id: Ib05806ac6108d465ffe245142ecca7a51be6df22
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There are two major issues with the kconfig:
() Some of the config options have incorrect dependencies inside help
under menuconfig. For example, CONFIG_GPIO depends on BOARD_GALILEO.
() Since the SoC and board specific kconfig files are parsed first,
the help screen would say, for example, CONFIG_SPI is defined at
arch/arm/soc/fsl_frdm_k64f/Kconfig. This is incorrect because
the actual config is defined in drivers/spi/Kconfig.
These cause great confusion to users of menuconfig/xconfig.
To fix these, the SoC and board defaults are now to be parsed last.
Note that the position swapping of defaults in this patch is due to
the fact the the default parsed last will be used.
And, spi_test is broken due to the fact that it requires
CONFIG_SPI_INTEL_PORT_1, but never enables it anywhere. This is
bypassed for now.
Origin: refactored and edited from existing files
Change-Id: I2a4b1ae5be4d27e68c960aa47d91ef350f2d500f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Changed names of Kconfig flags, variables, functions, files and
return codes consistent with names used in the RFC. Updated
relevant comments to match the changes.
Origin: Original
Change-Id: Ie7941032d7ad7af61fc02928f74538745e7966e8
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patch replaces all occurrences of DEV_* codes by errno.h codes at
the arch layer.
Change-Id: I1a1ab6d0481f3660ad032e2690d2577245fe1f34
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
() Moves the Quark SE clock control into its submenu.
() Fixes the dependencies in the SoC default Kconfig
so the options are not displayed out of place in
menuconfig.
Change-Id: Ifdf06242be8ceed03c2c657c942875a5a7f2750e
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This patch extends the UART QMSI driver so it supports the IRQ APIs from
include/uart.h. The IRQ APIs are enabled by the 'CONFIG_UART_INTERRUPT_
DRIVEN' option.
Differently from others APIs such as I2C and SPI, the UART API is very
low level. For that reason, the IRQ facilities (e.g. irq based transfers)
from the QMSI driver are not useful to the shim driver at the moment. In
order to implement the IRQ APIs we rely on UART registers defined by QMSI.
QMSI UART header is missing some macro definitions from IRR register so
we define them in the shim driver.
Since the IRQ trigger condition is not configurable in the QMSI shim
driver, this patch also changes drivers/serial/Kconfig so the "UART
IRQ Trigger Condition" choice doesn't appear on the menu if the QMSI
driver is selected.
Change-Id: Idf9a0f6a47af2a550a31f474d721068dca989713
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch introduces the QMSI UART driver which is simply a shim driver
based on UART driver provided by QMSI BSP.
This initial version implements only the mandatory APIs 'poll_in',
'poll_out' and 'err_check' which are required by trivial sample apps and
by output functionality from the console driver. The remaining APIs will
be implemented by up coming patches. The driver supports only 115200 baud
rate at the moment.
In order to enable this driver, the following options should be set:
CONFIG_QMSI_DRIVERS=y
CONFIG_QMSI_INSTALL_PATH="/path/to/libqmsi/directory"
CONFIG_SERIAL=y
CONFIG_UART_QMSI=y
This driver has been tested with Quark SE Devboard so this patch also
adds its platform-specific default configuration options to 'arch/x86/
soc/quark_se/Kconfig'.
Change-Id: Ibde1825d4b0349a376a8e7d91cc9de306946b62f
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch removes the macro UART_IOAPIC_FLAGS from Quark SE and D2000
soc.h since it is not used anywhere in the code.
Change-Id: I0fd42fac2f02e8617bd92c73c1a0354ef2d7a71a
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
The peripherals utilizing UART were required to register their own
ISR rountines. This means that all those peripherals drivers need
to know which IRQ line is attached to a UART controller, and all
the other config values required to register a ISR. This causes
scalibility issue as every board and peripherals have to define
those values.
Another reason for this patch is to support virtual serial ports.
Virtual serial ports do not have physical interrupt lines to
attach, and thus would not work.
This patch adds a simple callback mechanism, which calls a function
when UART interrupts are triggered. The low level plumbing still needs
to be done by the peripheral drivers, as these drivers may need to
access low level capability of UART to function correctly. This simply
moves the interrupt setup into the UART drivers themselves. By doing
this, the peripheral drivers do not need to know all the config values
to properly setup the interrupts and attaching the ISR. One drawback
is that this adds to the interrupt latency.
Note that this patch breaks backward compatibility in terms of
setting up interrupt for UART controller. How to use UART is still
the same.
This also addresses the following issues:
() UART driver for Atmel SAM3 currently does not support interrupts.
So remove the code from vector table. This will be updated when
there is interrupt support for the driver.
() Corrected some config options for Stellaris UART driver.
This was tested with samples/shell on Arduino 101, and on QEMU
(Cortex-M3 and x86).
Origin: original code
Change-Id: Ib4593d8ccd711f4e97d388c7293205d213be1aec
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Clockgating was disabled for RTC and disabling RTC had no
effect on Quark SE boards.
Change-Id: I67448d5582a206fc7a68d763d504e9f743043b53
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Anas Nashif