In order to simplify the handling of DMA_STM32_V1/V2 and DMAMUX_STM32
symbols, set them directly based on related compatible status.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Provides tool set to be used by device drivers in order to be able
to configure device signals.
This does not involve the implementation of a dedicated pinctrl
driver. In this regard, this is equivalent to implementation used
for treatment of current pinmux.c files.
Since STM32F1 uses a different GPIO configuration scheme, its
support is exlcuded for now.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Assuming we stay on default Power Scale 1,
overdrive is required when System Core Clock frequency is higher
than 180MHz.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The PWM drivers has been refactored using the HAL LL API. Not only that,
but the set pin_set function is now faster, as channel output compare is
just initialized if needed.
NOTE: Has been tested using H743zi board for now.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Added / Tested support for RNG on the STM32F767ZI nucleo board.
Updated the SoC defconfig to auto-enable the driver when
ENTROPY_GENERATOR is enabled, and updated the board README.
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
Remove DT_ADC_{0..2}_NAME from dts_fixup.h, if this casues the
dts_fixup.h file to be empty we remove the file as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Complete STM32 conversion to new DT macros by removing
remaining occurences of DT_ST_STM32_ADC_FOO_LABEL.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We don't need to define DT_NUM_IRQ_PRIO_BITS or DT_NUM_MPU_REGIONS in
dts_fixup.h files anymore, so we can remove them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Make use of DT_NODELABEL macros to get device instances
information to configure drivers I2C instances.
This allows to remove I2C related lines in fixup.h files
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use compatible information to configure i2c stm32.
With this, driver version selection is done thanks to compatible
and it is not needed anymore to do this via Kconfig symbol
selection under soc/
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Replace CONFIG_ENTROPY_NAME with DT_CHOSEN_ZEPHYR_ENTROPY_LABEL. We now
set zephyr,entropy in the chosen node of the device tree to the entropy
device.
This allows us to remove CONFIG_ENTROPY_NAME from dts_fixup.h. Also
remove any other stale ENTROPY related defines in dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To ease driver configuration, enable ENTROPY_STM32_RNG
only if device node matching driver compatible is enabled.
No more need to enable config symbol under soc/
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert stm32 entropy driver to configuration based on device tree.
Select HAS_DTS_ENTROPY symbols and configure CONFIG_ENTROPY_NAME
in fixup files.
Since rng node is not enabled (or available) on all boards, it could
happen that symbol ENTROPY_STM32_RNG is not enabled and hence
ENTROPY_HAS_DRIVER not selected which ends up with a symbol
ENTROPY_NAME defined throufg Kconfig selection. Thus, in fixup file,
CONFIG_ENTROPY_NAME is defined only if not already defined.
Additionally, update boards that used to configure entropy by default.
On these boards, enable rng device in device tree and remove Kconfig
related configuration (which should not be part of default
configuration).
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use device node declaration instead.
Clean up GPIO_STM32_PORT* Kconfig symbols.
On some boards some gpio ports where disabled using Kconfig symbols.
Disable them now via device tree nodes in boards dts files.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert usb_stm32 driver to use of DT_INST macros.
Since driver is compatible with 3 different dt compatibles and
compatible string is included in DT_INST macros, I've kept the
DT_USB_ compatible agnostic macros based on DT_INST ones, which
allowed to remove fixup definitions.
Use of DT_USB symbols is now limited to usb_dc_stm32.
Additionally, compatible "st,stm32-otgfs" is removed from list
of compatibles for usbotg_hs ips.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use DT_INST_ defines.
In the process, we've removed all UART/USART/LPUART code in
device instanciation code which had no impact.
Since all uart/usart/lpuart nodes declare compatibility with
st,stm32uart, DT_INST_X_ST_STM32_UART_FOO could be used.
Removed DT_UART fixup macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use DT_INST_ defines.
Removed DT_FLASH_DEV fixup macros, except DT_FLASH_DEV_NAME
used in applications.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use DT_INST_ defines.
Removed DT_RTC_0 fixup macros but keep DT_RTC_NAME_0 as it is
still in use across RTC users.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Include stm32XXxx_ll_utils.h in soc.h for every stm32 SoC,
if CONFIG_HWINFO_STM32 is selected.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Alexandre Bourdiol