* Add DTS support for gpio controller driver
Signed-off-by: Ashokkumar B <ashokkumar@zilogic.com>
Signed-off-by: Subash G <subash@zilogic.com>
Signed-off-by: Vishnu K <vishnu@zilogic.com>
Signed-off-by: Vaishnavi D <vaishnavi.d@zilogic.com>
By adding 'aliases' node in SoC .dtsi file it is possible to generate
DT_ defines which specify a logical name rather than relay on module
location on APB bus. E.g. DT_SILABS_GECKO_USART_40010000_LABEL becomes
DT_SILABS_GECKO_USART_USART_0_LABEL. Thus it is possible to remove
dts_fixup.h defines.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Fixes an ethernet build error introduced with MCUXpresso SDK 2.5.0,
caused by a slight change in the ethernet pll configuration structure.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add uart5 nodes to stm32f1 series dts.
Provide matching dts_fixup add-on.
Signed-off-by: Chen Han <qq1433255094@outlook.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Updates the MCUXpresso SDK to version 2.5.0 for applicable SoCs.
Wireless (KW*) and legacy (KL25) SoCs were not included in this
MCUXpresso SDK release and are therefore not updated here.
New in this release is SoC-level and board-level support for external
xip flash in the i.MX RT family.
For RT1050, we are now using the MCUXpresso SDK for the EVKB version of
the board, which correponds to an upgrade from A0 to A1 silicon.
However, we don't yet have Kconfigs in place to support A1 silicon part
numbers, and therefore add a simple cmake hack to convert A0 part
numbers to A1 part numbers.
The SDK flash driver interface also changed slightly in this release,
and thus the zephyr flash shim driver is updated accordingly.
Origin: MCUXpresso SDK
License: BSD 3-Clause
URL: mcux.nxp.com
Purpose: Provide device header files and bare metal peripheral drivers
for Kinetis, LPC, and i.MX SoCs.
Maintained-by: External
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add support for Low Speed External 32.768 kHz oscillator (LSE ).
Add support for MSI PLL-Mode offering an automatic calibration feature
in combination with the LSE. This allows the MSI to reach an accurate
+/-0,25% clock perfectly suitable for USB full-speed clock.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
SPI devices almost always require chip selects, which are configured
through GPIOs. Make the GPIO infrastructure available by default when
SPI is enabled.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
In the wake of introducing nRF9160 .dtsi header, we are
adding several HAS_HW_NRF_xxxx Kconfig symbols, for the
peripherals present in nrf9160 SoC.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Make the following nRF peripheral drivers:
- ADC
- GPIO
- I2C
- SPI
- UART
- USB_DEVICE
enabled by default so that users do not need to explicitly enable them
in their applications after choosing an nRF SoC as the build target.
Kconfig options enabling these drivers depend on both a given hardware
feature (e.g. I2C) and an nRF family SoC selected, so effectively they
will be automatically enabled only when it is adequate (and in most
cases these drivers are the only option for a given hardware feature
on nRF SoCs).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Implementations of both flavors of serial drivers for Nordic SoCs
are no longer dependent on the gpio driver. Remove the dependency
from Kconfig.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Added board definitions for nucleo_f756zg. Features include gpio,
pinmux, uart (ST Zio, ST-Link and Arduino Uno v3 interfaces).
Added basic documentation and some soc definitions for the
stm32 f756XX soc.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
The various linker scripts on arc would include autoconf.h in the arch
linker script but might have CONFIG_ symbols referenced in the soc
specific linker script. Move autoconf.h inclusion to top of the soc
specific linker script out of the arch specific one so we know
autoconf.h is seen before any CONFIG_ references.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The early boot watchdog init for kinetis was incorrectly disabling and
reenabling interrupts to preserve timing during the unlock sequence.
However, interrupts are already disabled before this routine executes
and the kernel is not yet ready to enable them when this routine exits.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds a flash driver for the STM32F7x series, inspired from
the STM32F4x one. It has been tested on the STM32F723, but should also
work on other SoCs of the family.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This patch cleans up the code in the recently added dts_fixup.h,
restoring the original alignment of the file.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The dts.fixup for v2m_beetle contains a wrong setting for the IRQ fixup
for the Dual Timer IRQ.
This patch fixes the symbol included in the generated header.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This commit simplifies Kconfig options related to handling SoC series,
part numbers. This is a first step required to add remaining part
numbers to the existing configuration.
This change is possible since all SiLabs SoCs within a single series
have a very uniform structure.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
All text, data and bss sections are all mapped to the same physical
memory (SRAM). This patch removes the individual section limits
and defines a common limit for the sum of text, data and bss sections.
This would make it more flexible for application developers.
Fixes#11268.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
CONFIG_TEXT_SECTION_OFFSET allows the entire image to be moved
in memory to allow space for some type of header. The mcubootloader
can boot only such images which reserve some space for the header.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
RISC-V permits myriad extensions to the ISA, any of which may imply
additional context that must be saved and restored on ISR entry and
exit. The current in-tree example is the Pulpino core, which has extra
registers used by ISA extensions for running loops that shouldn't get
clobbered by an ISR.
This is currently supported by including pulpino-specific definitions
in the generic architecture code. This works, but it's a bit inelegant
and is something of a layering violation. A more generic mechanism is
required to support other RISC-V SoCs with similar requirements
without cluttering the arch code too much.
Provide that by extending the semantics of the existing
CONFIG_RISCV_SOC_CONTEXT_SAVE option to allow other SoCs to allocate
space for saving and restoring their own state, promoting the
currently pulpino-specific __soc_save_context / __soc_restore_context
routines to a RISC-V arch API.
The cost of making this generic is two more instructions in each ISR
to pass the SoC specific context to these routines in a0 rather than
just assuming the stack points to the right place. This is minimal,
and should have been done anyway to keep with the ABI.
As a first (and currently only in-tree) customer, convert the Pulpino
SoC code to this new mechanism.
Signed-off-by: Marti Bolivar <marti@foundries.io>
The driver can be tested using different networking emulation
approaches.
This approach will work across multiple Qemu instances. There can be
more than one Qemu instance, run using the following command. They
would appear to be on the same Ethernet network.
$ qemu-system-arm -M lm3s6965evb \
-serial stdio \
-net nic \
-net socket,mcast=230.0.0.1:1234 \
-kernel zephyr.elf
This approach will work with other virtualization technologies that
support connecting to a VDE switch, like VirtualBox and User Mode
Linux. The switch can be started using the following command.
$ vde_switch --sock /tmp/switch
Qemu can be connected to the switch using the following command.
$ qemu-system-arm -M lm3s6965evb \
-serial stdio \
-net nic \
-net vde,sock=/tmp/switch \
-kernel zephyr.elf
Signed-off-by: Fadhel Habeeb <fadhel@zilogic.com>
Signed-off-by: Nirav Parmar <niravparmar@zilogic.com>
Signed-off-by: Vijay Kumar B <vijaykumar@zilogic.com>
Add configuration values for HAS_HW_NRF_BPROT and HAS_HW_NRF_MPU.
Select these configurations where applicable.
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
Since pinmux configuration is board dependent and is now under
boards/xtensa/intel_s1000, the configuration in soc.c is removed.
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Within a single series pin mapping between location setting and pin name
is uniform. The only difference is availability of the module, i.e. i2c1
may be missing on some part numbers, or availability of the pin, i.e.
32 pin package will not provide all the pins available on 48 pin
package. It's better to manage these differences at the DTS/Kconfig
level.
This commit removes dependency of soc_pinmap.h files on part numbers.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
There were many platforms where this function was doing nothing. Just
merging its functionality with _PrepC function.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Implementation taken from Nordic nrfx version 1.3.1 soc/nrfx_coredep.h,
modified to remove material from other series and to conform to Zephyr
coding standards.
Note that unlike standard k_busy_wait this is susceptible to
longer-than-intended delays due to the impact of interrupt handling.
Fixes#11626
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The Cortex-M7 CPU included in the SAM e70 SoCs has a data cache that
significantly boost the performances. However the SAM GMAC Ethernet
driver is using a scatter-gather technique to exchange data with the
Ethernet driver. This requires the use use of a non-cached memory area.
This is currently not supported on Zephyr, but support for it is being
discussed in PR#11199.
In the meantime, enable the data cache during the SoC initialization,
unless the SAM GMAC Ethernet driver is enabled.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The Cortex-M7 CPU included in the SAM e70 SoCs has an instruction cache
that significantly boost the performances. Enable it during the SoC
initialization.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Ashokkumar B