These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
I have no idea what I was thinking when I wrote this.
But, it's an easy fix to remove the void * entirely.
Signed-off-by: Michael Scott <mike@foundries.io>
New shell implementation is on the way. For now old one and all
references are kept to be gradually replaced by new shell.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The return of memset is never checked. This patch explicitly ignore
the return to avoid MISRA-C violations.
The only directory excluded directory was ext/* since it contains
only imported code.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
These settings enable use of the WNC-M14A2A LTE-M modem as the default
network interface for the nRF52840-DK board (nrf52840_pca10056).
They include the following settings when MODEM_WNCM14A2A is selected:
- UARTE1 pin setup
- DTS / DTS fixup additions for WNC-M14A2A
- Kconfig settings for modem driver
Signed-off-by: Michael Scott <mike@foundries.io>
These settings enable use of the WNC-M14A2A LTE-M modem as the default
network interface instead of ethernet.
They include the following settings when MODEM_WNCM14A2A is selected:
- UART 2 setup
- Avoid ETH_0 setup due to pin conflicts
- DTS addition for WNC-M14A2A
- Kconfig settings for modem driver
Signed-off-by: Michael Scott <mike@foundries.io>
Add a set of modem shell commands to support modem development.
Start with:
modem list: Lists all registered modems and related information
modem send <modem receiver index> <command>: Send command to modem
Signed-off-by: Michael Scott <mike@foundries.io>
The WNC-M14A2A (LTE / LTE-M) modem is presented as an Arduino-
compatible shield via AT&T's IoT Starter Kit v1.0. It was
originally intended to work with the FRDM-K64F board, but
in theory as long as the right pins are configured it can
work with any board that supports Arduino-compatible headers.
The driver utilizes the CONFIG_NET_OFFLOAD setting to avoid the
normal handling of IP packets, and instead uses a socket-like
UART interface to handle incoming and outgoing data.
Signed-off-by: Michael Scott <mike@foundries.io>
Modem drivers need a fast buffer-based receiver for passing data
back and forth from the UART to the driver. This provides an
efficient configuarable driver which merely sends and receives
but doesn't process the data, that's left up to the modem driver.
Signed-off-by: Michael Scott <mike@foundries.io>
Andrzej Głąbek