Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Sample projects that pair the frdm_k64f board with a cc2520 require
additional pinmux settings beyond the standard frdm_k64f pinmux. These
settings used the private k64 pinmux API rather than the public pinmux
API.
Because the mcux pinmux driver now always supports the public pinmux API
(vs. the k64 pinmux driver which only supported it in pinmux dev mode),
we can convert the frdm_k64f_cc2520 projects to use the public pinmux
API and the mcux pinmux driver.
Change-Id: Idfae8393171b007d8629e34bfae64255f55c6792
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Common code found in samples/net/common
App is built with:
make BOARD=frdm_k64f CONF_FILE=prj_frdm_k64f_cc2520.conf
Note: debug messages are enabled on many parts of the system, and these
are killing the timings. So it's not unusual at all to see rx errors on
cc2520 side. Without most of the debug, much less error will occur (if
any when dbg is fully disabled).
Change-Id: Ib6f0868c300652270661e72e80108804308164ab
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
CC2520 is not embedded on an arduino_101, it is however possible to wire
one, and thus it requires to provide cc2520_configure_gpios() function.
This one, being common to a101 is found in samples/net/common.
Change-Id: I86f2734847edb3f6a968522afccc3099ed854d13
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This enables application debugging using qemu target:
export QEMU_EXTRA_FLAGS="-s -S"
make qemu
Was tested with echo_server
Change-Id: I1906dea2fbc5afe03b11729d2edb8f3629a629f8
Signed-off-by: Ruslan Mstoi <ruslan.mstoi@intel.com>
- net tools directory is now in net/tools
- fixing the 80 chars line limit
Change-Id: I079880fa3449beffb326369ab23550dcba3ccf20
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
NET_TESTING_USE_RFC3849_ADDRESSES not defined as a Kconfig option.
Enable this in Makefile like this
ccflags-y +=-DNET_TESTING_USE_RFC3849_ADDRESSES=1 incase if you need
it.
Change-Id: I96b05d069cf5baa56cc27489b3c38b84412eec97
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Provide pcap support for echo-apps with PCAP=<filename> option.
For pcap support:
make server NET_IFACE=qemu PCAP=sample.pcap.
without pcap support:
make server NET_IFACE=qemu
Change-Id: Iad90064e0c32134f9c2fda7b28e2cbca1e4e931c
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Set the IPv4 address, netmask and default router addresses
that are used for automatic testing.
Change-Id: Iebddc42c56dceeb089af7878102f8a73c30f0b74
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Makefile.ipstack is more generic to net applications which
communicate through slip or between two qemus. So net apps
common folder is right place for it.
Change-Id: I57ca1eeaff28b853609daf92772361406131aa7e
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Collect common routines used in every network sample application
into same file. These routines are used when testing with
qemu and slip.
Change-Id: I02f20b3a9bfa1e886846801b22f43a1d06c59930
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>