Add a new clock control driver for NXP Kinetis SoCs that have the
Peripheral Clock Controller module (PCC).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This menu contains just the MCUMGR symbol and its children. Get rid of
one menu level by removing it.
Makes the 'External Sources' menu look like this:
HALs --->
Cryptography --->
[ ] Fnmatch Support
[ ] OpenAMP Support
(open-amp) OpenAMP library source path
[ ] mcumgr Support
('OpenAMP library source path' being visible there might be a separate
issue.)
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit adds basic support for nrf52811 in the arch SoC, dts
and nrfx folders.
The nRF52811 is a Bluetooth 5.1 Direction Finding SoC with comprehensive
protocol support.
The nRF52811 SoC is capable of the latest features of Bluetooth 5.1,
the most prominent being Direction Finding.
The radio in the nRF52811 SoC has comprehensive protocol capabilities,
including Bluetooth 5.1 Directing Finding, all Bluetooth 5 features,
802.15.4, Thread, Zigbee, ANT and 2.4 GHz proprietary.
It has 4 dBm TX power and has been optimized to offer the best RX
sensitivity of all SoCs in the nRF52 series.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
This patch adds support for the revision B of the SAM E70 SoC. It adds
all the rev B part numbers, and when users pick-up one of those part
numbers, the revision B HAL is used instead.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This is an import of Atmel SAM E70 HAL version 2.3.98, for the revision
B of the chip. The files have been passed through dos2unix to minimize
the differences with the revision A which seems to also have been
imported that way.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Implement newly introduced `configure` API for nRF 802154 radio driver.
Increase maximum number of slots for Frame Pending bit information in
the radio driver.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
License link provided in stm32cube abstract packages was not
reflecting the actual license in use for these packages.
Update the link to BSD 3-Clause official.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Mark the PPI channels and groups used by the Bluetooth controller
as occupied and thus unavailable for allocation through nrfx_ppi.
Add also a build time assertion that checks if these PPI channels
do not overlap with those assigned to the pwm_nrf5_sw driver
(to replace the comments in this driver that were supposed to warn
about this threat but had in fact little chance to be read by users).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Mark the PPI channels used by the pwm_nrf5_sw driver as occupied
and thus unavailable for allocation through nrfx_ppi.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add initial support for the TI CC13x2 / CC26x2 series with the CC2652R
and CC1352R SoCs. The UART and GPIO peripherals are supported. Drivers
use the driverlib HAL from the TI CC13x2 / CC26x2 SDK.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
The default customer configuration (CCFG) provided by the
TI CC13x2 / CC26x2 SDK puts the configuration in a section different
than expected by Zephyr. It has been modified to use the appropriate
section.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Add low level drivers (driverlib) and RF patches from the TI CC13x2 and
CC26x2 SDK. These sources have been added unmodified with the exception
of converting DOS to UNIX line endings.
The majority of these APIs are available in ROM and inclusion of the
headers will map functions that are not inline to the ROM versions.
Origin: Texas Instruments SimpleLink CC13x2 and CC26x2 SDK
License: BSD 3-Clause
URL: http://www.ti.com/tool/simplelink-cc13x2-26x2-sdk
Purpose: Provides HAL for TI CC13x2 and CC26x2 SoCs
Maintained-by: External
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
SVCall_IRQn is used as enum value for SV Call Interrupt for Cortex-M
based SoCs for which CPU_CORTEX_M_HAS_BASEPRI=y. However stm32cube
for stm32l1xx uses SVC_IRQn enum value for this purpose.
This leads to this error:
arch/arm/include/cortex_m/exc.h:101:19: error: 'SVCall_IRQn'
undeclared (first use in this function); did you mean 'SVC_IRQn'?
NVIC_SetPriority(SVCall_IRQn, _EXC_SVC_PRIO);
^~~~~~~~~~~
SVC_IRQn
NB: ext/hal/st/stm32cube/stm32l1xx/soc/stm32l151xb.h file was already
fixed in 9f8260457b ('ext: hal: st: stm32cube: Add HAL for
the STM32L1x series').
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Atmel Software Framework (ASF) provides a set of low-level header
files that give access to different hardware peripherals of Atmel's
ICs.
Origin: Atmel SAMR21 Series Device Support (1.1.72)
License: Apache-2.0
URL: http://packs.download.atmel.com/Atmel.SAMR21_DFP.1.1.72.atpack
Purpose: Introduction of ASF for the SAM0 series.
Maintained-by: External
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
This commit adds the STM32CUBE HAL for STM32L1x series MCUs.
Origin: ST Microelectronics
License: BSD-3-Clause
URL: http://www.st.com/en/embedded-software/stm32cubel1.html
Commit: 1.8.0
Purpose: HAL layer for STM32L1
Maintained-by: External
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Following introduction of STM32Cube for STM32WB, update stm32cube
folder to enable build of STM32WB Cube package.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This adds the HAL code needed for the SoC for the stm32wb series.
Origin: ST Microelectronics
License: BSD-3-Clause
URL: http://www.st.com/en/embedded-software/stm32cubewb.html
Commit: 1.0.0
Purpose: HAL layer for stm32wb
Maintained-by: External
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The CONFIG_ prefix is reserved in Zephyr, rename CONFIG_SHIFT and
associated constants by adding a RCC_ prefix
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
The stm32mp1 exti ll driver is mandatory for compilation.
add it on top of stm32cubeMP1 version 1.0.0.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Provide required changes to stm32cube HAL and LL for the
STM32MP1X series MCU.
Origin: ST Microelectronics
License: BSD-3-Clause
URL: https://github.com/STMicroelectronics/STM32CubeMP1
Commit: 1.1.0
Purpose: HAL layer for STM32MP1
Maintained-by: External
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Introduce nrfx_nvmc driver into nordic flash driver implementation.
Thanks to that nrf9160 SoC becomes supported by the driver.
nrfx helps dealing with differences with interface to the NVMC
in secure and non-secure execution modes.
This patch adds NRFX_NVMC Kconfig entry for enabling nrfx_nvmc and
select it along with nordic flash driver.
Disabled UICR operation on nRF9160 for non-secure build
as UICR is not available in this mode.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add mcux 2.5.0 drivers and device header files for mimxrt1015. Update
several drivers that were already imported for other SoCs but also apply
to mimxrt1015.
Origins: NXP MCUxpresso SDK 2.5.0
URL: mcuxpresso.nxp.com
Maintained-by: External
Signed-off-by: Ryan QIAN <jianghao.qian@nxp.com>
Add driver and device tree binding for the Low Power Inter-Integrated
Circuit (LPI2C) controllers found in the RV32M1 RI5CY SoC.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Building with clang reports the following warnings:
stm32l4xx_hal_tim.c: error: equality comparison with extraneous
parentheses [-Werror,-Wparentheses-equality]
else if((htim->State == HAL_TIM_STATE_READY))
~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~
Removing the extra () fixes the warning
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Building with clang reports the following warnings:
stm32l0xx_hal_tim.c: error: equality comparison with extraneous
parentheses [-Werror,-Wparentheses-equality]
else if((htim->State == HAL_TIM_STATE_READY))
~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~
Removing the extra () fixes the warning
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Building with clang reports the following warnings:
stm32f7xx_hal_tim.c: error: equality comparison with extraneous
parentheses [-Werror,-Wparentheses-equality]
else if((htim->State == HAL_TIM_STATE_READY))
~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~
Removing the extra () fixes the warning
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Building with clang reports the following warnings:
stm32f4xx_hal_tim.c:3615:24: error: equality comparison with extraneous
parentheses [-Werror,-Wparentheses-equality]
else if((htim->State == HAL_TIM_STATE_READY))
~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~
Removing the extra () fixes the warning
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Building with clang reports the following warnings:
stm32f3xx_hal_tim.c: error: equality comparison with extraneous
parentheses [-Werror,-Wparentheses-equality]
else if((htim->State == HAL_TIM_STATE_READY))
~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~
Removing the extra () fixes the warning
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Building with clang reports the following warnings:
stm32f2xx_hal_tim.c: error: equality comparison with extraneous
parentheses [-Werror,-Wparentheses-equality]
else if((htim->State == HAL_TIM_STATE_READY))
~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~
Removing the extra () fixes the warning
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Building with clang reports the following warnings:
stm32f1xx_hal_tim.c: error: equality comparison with extraneous
parentheses [-Werror,-Wparentheses-equality]
else if((htim->State == HAL_TIM_STATE_READY))
~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~
Removing the extra () fixes the warning
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Building with clang reports the following warnings:
stm32f0xx_hal_tim.c: error: equality comparison with extraneous
parentheses [-Werror,-Wparentheses-equality]
else if((htim->State == HAL_TIM_STATE_READY))
~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~
Removing the extra () fixes the warning
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Discovered with pylint3.
Use the placeholder name '_' for unproblematic unused variables. It's
what I'm used to, and pylint knows not to flag it.
Python tip:
for i in range(n):
some_list.append(0)
can be replaced with
some_list += n*[0]
Similarly, 3*'\t' gives '\t\t\t'.
(Relevant here because pylint flagged the loop index as unused.)
To do integer division in Python 3, use // instead of /.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
In case of double buffering (two capture buffers), the CSI is
frequently starved because of a lack of buffer in the active pool.
You can find below an example of double buffering scenario:
FREE_BUF ACTIVE_BUF
start: 0 2
frame0_complete: 0 1 (no buffer to load in active)
resubmit_frame0: 1 1
frame1_complete: 1 0 (CSI stopped, active buf = 0)
resubmit_frame1: 2 0
0 -> 2 (CSI restarted)
This patch solves this issue by loading buffer to active at submit
time.
FREE_BUF ACTIVE_BUF
start: 0 2
frame0_complete: 0 1
resubmit_frame0: 1 1
0 -> 2 (Direct load to active)
frame1_complete: 0 1
resubmit_frame1: 1 1
0 -> 2
...
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Use tinycbor from the tinycbor repo directly and drop the library from
ext/.
Add entry to west.yml and update SHA.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Adding additional workarounds to cc_pal.h that are necessary due to the
fact that the POSIX subsys does not integrate well with other parts of
Zephyr, as per discussion in #13444. These workarounds are needed when
fcntl.h is included, to avoid symbols from being redefined in POSIX
headers. They disable some POSIX headers and define what is necessary
for the code to compile.
We should aim to remove these when the integration story has improved.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Appears within an 'if MBEDTLS'.
'if FOO' is just shorthand for adding 'depends on FOO' to each item
within the 'if'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Maybe this is some "just in case" thing that got copied around. There's
no need to have a blank line at the beginning or end of Kconfig files.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Henrik Brix Andersen