Remove dev driver and integrate it in the default pinmux driver.
Jira: ZEP-958
Change-Id: I55670240f8a21749d3a6ae22e300e16ba80a2fb6
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Implementation includes adding some defines in the pinmux,
adjusting gpio driver to specific defines for STM32F3X family,
adding specific functionality in the F3X SoC definition.
Change-Id: I465c66eb93e7afb43166c4585c852e284b0d6e67
Signed-off-by: Adam Podogrocki <adam.podogrocki@rndity.com>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The k64 pinmux driver was deprecated when the more generic mcux pinmux
driver was added, but it can actually just be removed because it is not
a public interface. Applications should be using the public pinmux API,
not the private k64 pinmux API. There was one case in the net samples
that used the private API which was cleaned up in a previous patch.
Change-Id: I49a6397baa57973930cb63bd2a9883b14f7ddafd
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Changes the init level for the mcux pinmux driver from POST_KERNEL to
PRE_KERNEL_1. This will allow moving the uart console pins from the k64
soc init to the board pinmux tables.
Change-Id: I6d3377c9a689c12711c84387f74843ca9488df52
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The ksdk pinmux dev driver was previously merged into the regular ksdk
pinmux driver, and the config PINMUX_DEV_KSDK was removed. Two
references were inadvertantly left behind, so remove them now.
Change-Id: I77394be5459d55a9f16e7bd2b3c9d688c4605b4f
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Merges the ksdk pinmux dev driver into the regular ksdk pinmux driver,
which now exposes the public pinmux API. Removes the private ksdk pinmux
API and converts the frdm_k64f and hexiwear_k64 boards to use the public
pinmux API.
Jira: ZEP-958, ZEP-1432
Change-Id: Ie5f60b604133093050b9c596050cad776d7b7cb3
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
replace include <nanokernel.h> with <kernel.h> everywhere and also fix
any remaining mentions of nanokernel.
Keep the legacy samples/tests as is.
Change-Id: Iac48447bd191e83f21a719c69dc26233216d08dc
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Now that we have a more generic ksdk pinmux driver that can be used
across multiple Kinetis SoCs, deprecate the specific k64 pinmux driver.
Jira: ZEP-1393
Change-Id: I11cfe9a53746a6e85eced2a7cecf0396d42a7a19
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Kinetis SoCs contain one or more PORT modules to handle pin muxing and
pin configuration. Unlike the existing k64 pinmux driver, this driver
handles each PORT module individually and can be used for other Kinetis
SoCs.
This driver uses KSDK CMSIS register accesses to the PORT module rather
than the KSDK PORT driver (fsl_port.h), because the Zephyr pinmux
interface contains both set() and get() functions to access the pin
configuration. The KSDK PORT driver only contains a set() function
(which is a very thin static inline function to modify the PCR
register), therefore building a shim on top of it would result in a
strange mix of using the KSDK PORT driver for the set() and a direct
CMSIS register access for the get().
Jira: ZEP-1393
Change-Id: I2f7c6b08b207350697d590dcd665223f81de9f9e
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add pin config for PWM support on ST Nucleo boards
Following config is chosen:
-PA0/PWM2_CH1 for F401RE and L476RG
-PA8/PWM1_CH2 for F103RB
Change-Id: I013e15ed35360d7777bb24ff94e0830f913a6580
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add board support for the Nucleo64 L476RG development board.
Change-Id: Ibb5424bc936c67a5d96855617202136d7dea772c
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add all possible pin assignment definitions for I2C{1-3} on STM32L4xx.
Change-Id: I2d4266bc3bb9ba41b74a80567c0b04a89963753e
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add macro for all the available pinmux for the USARTs present on
STM32L4.
Change-Id: Ie4352750e1c6f08642b3e222b57f2a791f08ef74
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There was a misalignment between Zephyr UART device numbering and
SoC UART IP. Device "UART_1" was mapped to IP USART_2, which could
be confusing for user.
This commit allows to align "UART_1" to IP USART_1.
Change is propagated to all STM32F103RB/STM32F401RE based boards and
respective pinmux drivers
Change-Id: Ia8099dfeec7b9c0c686c2a58ccb4dbb1a55b6537
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit replaces the nanokernel.h include by kernel.h.
Change-Id: Ib42fbf2d9f77a73c0831f569b3dbbfb342ea2e1d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Pinmux driver almost certainly should be initialized before the
rest of hardware devices (which may need specific pins already
configured for them), and usually after generic GPIO drivers.
Thus, its priority should be between KERNEL_INIT_PRIORITY_DEFAULT
(default 40) and KERNEL_INIT_PRIORITY_DEVICE (default 50). Thus,
we set PINMUX_INIT_PRIORITY to 45.
There are exceptions to the rule above for particular boards. For
example, BOARD=galileo has GPIO and pinmuxer on I2C bus and thus
overrides PINMUX_INIT_PRIORITY to be much higher. Note that while
PINMUX_INIT_PRIORITY was defined previously (at 60), it was used
only for galileo, which overrides it anyway.
This fix was prompted by investigation why eth_ksdk driver was
non-functional after kernel priorities re-hashing: both eth_ksdk
and pinmux used the same priority, and eth_ksdk happened to run
before pinmux. While bumping eth_ksdk priority would help in the
particular case, the same would likely reoccur with other drivers
like I2C, SPI, etc.
Change-Id: Ie5ca3135c1ee2fe8d9cf48d5c12e62eac63487f7
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This patch adds the support for "runtime" pinmux on ARM V2M Beetle.
The GPIO controllers 2 and 3 are reserved and therefore not exposed
by this driver.
Jira: ZEP-1245
Change-Id: I9637f1a0d2bf6a757e1942160fb170165ffe6a0c
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds the support for the board pinmux initialization on
ARM V2M Beetle.
The GPIO controllers 2 and 3 are reserved and therefore neither exposed
nor configured by this driver.
Jira: ZEP-1245
Change-Id: Id5499c5dd887c319730408eeb30f02eeed1c3699
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
These pins are routed to the arduino header, and configuring them for
UART signals allows us to use the frdm_k64f with a frdm_kw40z shield
board for bluetooth.
Change-Id: Ie30916409844b1dc1c6e1280d5a755a6dc42e418
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add the definition required to change the pinmux of port H.
Change-Id: I3cc107f9151db4d38fe2cace90cd02d5955a2717
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for the STM32F401 chip on the board
Change-Id: I96c0799f3658ecea096fa5971bce9faf21919ee1
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change the clock accessors to a tuple of bus ID of the subsystem and enable
bits for the device - it is clearer to read than the opaque pointers.
Change-Id: I9ae73c222c04adac4cf2bc06e97f4ec199bdac3c
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
STM32F401 allows for upto 16 alternate functions on each pin.
Change-Id: Ib1c14fd31abaa2b05a5ab0f7bd1b4a4748f10f84
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
STM32F4 requires the alternative function config to be set, so just
initialize that as part of the gpio configure call.
Change-Id: I33a4a8efec59c5ebe7dc3f3580f0dd2bf7ded7f4
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
The hexiwear board has a k64 SoC, so we can reuse the k64 pinmux driver
and just add a new pinmux table for the board.
Jira: ZEP-716
Change-Id: I936691b3578db298014f44fe18433d7943b431f3
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Anas Nashif