This adds a translation layer to make the nrfx driver for the nRF SPIS
(SPI Slave with EasyDMA) peripheral accessible via the Zephyr's API.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Synchronous call return them on success, asynchronous one - with proper
signal - require to get this info through the status.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- removing a left over from previous SPI slave attempt
- unlock async calls on error
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Introduced with the commit 7a9c4cbd9d,
by copy-pasting from "spi_nrfx_spim.c". Shame on me...
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Similar parts of code are aligned in the two shims, so that they
can be easily compared and updated if required.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This adds a translation layer to make the nrfx driver for the nRF SPIM
(SPI Master with EasyDMA) peripheral accessible via the Zephyr's API.
The shim is provided only for nRF52840 because of a hardware anomaly
present in nRF52832. See Anomaly 58 (SPIM: An additional byte is clocked
out when RXD.MAXCNT = 1) in Errata for this chip.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The simple function that helps to integrate nrfx IRQ handlers with
the IRQ_CONNECT macro can be used in shims for various nrfx drivers,
not only the SPI one.
Similarly, the macro for getting the IRQ number from the peripheral
base address needs to be widely available. It should be even moved
to <nrfx_common.h> in some next nrfx update.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Logical or is unsufficent for setting up new tmod: it's required to
remove previous one first. Indeed, 0 as tmod is valid (tx-rx mode), but
previous tmod could be 10 or 01, so a logical or will keep the previous
tmod leading to a bogus transaction.
Fixing also a rebase issue visible when debug mode is enabled. Slave
callback is a left over from a test on spi slave.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It involves a minor change on which register is configured.
Most of the change is with threshold handling.
Handling the Kconfig based supported mode per-port.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This adds a translation layer to make the nrfx driver for the legacy
(i.e. without EasyDMA) nRF SPI peripheral accessible via the updated
Zephyr's API of the SPI driver.
Configuration files are already prepared for adding support for SPIM
(Master with EasyDMA) and SPIS (Slave with EasyDMA) peripherals.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Now that MCR20A supports the new API, legacy support from mcux dspi
driver can be safely removed.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Adds support for the new spi api to the mcux dspi shim driver. Does not
remove support for the legacy spi api since there are still consumers of
that api, particularly the mcr20a 802.15.4 driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
As for RX only, computing the NDF will be used for EEPROM mode.
Only a way to determine EEPROM mode is missing.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Some device may need to be put up on CS high logic. The active low logic
is the default as usual, but it is now possible to request the active
high logic.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Adding Kconfig options to set supported modes by the controller
(master, slave or both)
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Instead of using CONFIG_POLL, which is not directly related to SPI and
is a kernel option, let's have SPI_ASYNC instead. When enabled, it will
select POLL automatically.
Fixes#5839
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
tx_bufs/tx_count and rx_bufs/rx_count can be hold in another dedicated
structure, thus reducing the number of parameters to transceive. This
permits to avoid using the stack when calling transceive.
Since we saved parameters, we can expose back the struct device pointer,
to stay consistent with other device driver APIs.
Fixes#5839
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As the content of this struct will not be modified by drivers, it's
better to pass it as constant. Also, if someday struct device can be
made contant too, this change will make spi ready for registering the
spi_config into ROM directly.
Fixes#5839
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Split QMSI relevant part into its own file. Some config where using
prompt, some not: normalizing it by removing the prompt keyword where
relevant.
Reducing the file by using if/endif when relevant.
However, it still not fully clean default: cfg and default baudrate
should disappear. There is no default configuration to apply as long
as the controller is not configured to run from any part using spi API.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The previous help text rendered as a single paragraph in the Kconfig RST
reference. The new help text renders as a bullet list and matches the
format of SYS_LOG_CRYPTO_LEVEL.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Upcoming Nordic ICs that share many of the peripherals and architecture
with the currently supported nRF5x ones are no longer part of the nRF5
family. In order to accomodate that, rename the SoC family from nrf5 to
nrf, so that it can contain all of the members of the wider Nordic
family.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fixes#6577.
Wait for all ongoing transmits to complete before de-asserting CS.
When doing a tx then rx, wait for the previous tx to complete before
flushing the rx buffer.
Tested on the Arduino Zero against a Olimex MOD-NRF24L module.
Signed-off-by: Michael Hope <mlhx@google.com>
Switch the SoC device tree to define a single entry per SERCOM instead
of one per mode.
Define a Device Tree binding for the SAM0 SPI and use it instead of
Kconfig for enabling / disabaling instances
Switch the Arduino Zero, Adafruit Feather M0 Basic Proto, and
Trinket M0 to use the new defintion.
Add the APA102 LED that's on the Trinket as a test.
Signed-off-by: Michael Hope <mlhx@google.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix Kconfig help sections and add spacing to be consistent across all
Kconfig file. In a previous run we missed a few.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Also pull out the SERCOM pads configuration to defines. Note that the
SAM0 has a two level configuration - a signal (like TX) is mapped to a
pad, and then a pad is mapped to a function on a pin.
Signed-off-by: Michael Hope <mlhx@google.com>
This patches fixes a few bugs with the SAM0 driver:
- txrx was trasnmitting too many bytes
- adds support for NULL buffers to the fast paths
- fixes a NULL dereference on the rx buffer slow path
The tests under tests/driver/spi/spi_loopback now pass.
Signed-off-by: Michael Hope <mlhx@google.com>
Current buffers might be configured to skip data, thus only len will be
set, buf will be NULL. Buffer should be used if only len is > 0 and
buffer is valid as well.
tx/rx are "on" if len is > 0
tx/rx buf should be touched if only len is > 0 _and_ buf != NULL.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Use "select USE_STM32_LL_SPI" to select the needed STM32 LL files,
instead of editing ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
The SAM0 series has up to 6 SPI ports. Add Kconfig options to match.
Similar to the 9033fb2f01, this patch
only defines the fields that are currently used and skips ones like
GPIO and IRQ priority that aren't.
Signed-off-by: Michael Hope <mlhx@google.com>
Håkon Øye Amundsen