Take the int-pin information (i.e. what pin between INT1
and INT2 the drdy is attached to) directly from DT.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The display controller and SDMMC slot both define GPIOs for their chip
select signals, so enable GPIO drivers by default for this shield.
This missing default was discovered in CI when extending the fat_fs
sample to build with this shield. Many boards enable GPIO drivers by
default, but some boards like sam_v71_xult and sam_v71b_xult do not.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Configures the adafruit_2_8_tft_touch_v2 shield board to enable SDMMC by
default when disk drivers are enabled.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The device tree overlay for the adafruit_2_8_tft_touch_v2 shield board
was incorrectly mapping the Arduino D4 pin, used for SDMMC chip select.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The Semtech SX1272MB2DAS shield is populated with a SX1272 LoRa
transceiver. The base board must provide Arduino header pins
definitions.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Convert ism330dhcx INT_PIN attribute from Kconfigs to Device
Tree binding properties. Here int-pin has been defined as
enum with two possible values: 1 and 2.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Aligning the boostxl_ulpsense shield with all other shield
descriptions by ensuring it has a Kconfig.shield file.
This also provides the Kconfig symbol SHIELD_BOOSTXL_ULPSENSE similar
to the Kconfig symbol available for other shields.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
The IIS2DLPC drdy interrupt can be routed to either INT1 or
INT2 pin. Currently the selection is done by Kconfig configuration.
This commit is instead moving it into Device Tree as 'drdy-int'.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
On stm32mp157c_dk2, the pin mapped on arduino connector pin A3
could not be used as GPIO.
As a consequence, pin "irq-gpio" from x_nucleo_iks01a3 shield
should not be used.
Use board overlay to remove it from shield definition.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add support for the BuyDisplay 3.5" TFT + touch shield based on ILI9488
controller and FT6236 touch.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Make driver generic for multiple ILI displays. The adopted strategy is
to share all driver code except register initialization, which has been
found to have some specific registers/values depending on the
controller.
The driver has been adjusted to support multiple compatibles.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Move the data/command GPIO from Arduino header 16 (D10), which collides
with Arduino SPI SS, to Arduino header 15 (D9).
Add commented example for specifying a reset GPIO on Arduino header 14
(D8).
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add Inventek es-WIFI modules shield. This shield exposes es-WIFI driver
using Arduino Uno R3 header by UART or SPI interfaces. It shows how
user can create their own overlay and expose es-WIFI driver.
The current Inventek's EVB doesn't have all pins necessary to control
the module by Arduino hearder. This shows how to wire to get ISM43xx
EVB working.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
This change allows to use SSD1306 based displays to be used on the
SPI bus as well.
Adding SPI shield.
Tested on SSD1306 and SSD1309 based displays using I2C.
Tested on SSD1309 based display using SPI.
Signed-off-by: Marco Peter <marco@peter-net.ch>
Move pixel format setting (RGB565/RGB888) to DeviceTree. Add support for
changing pixel format at runtime.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add support for the ARM DesignStart DAPLink board for Digilent Arty
S7/A7 (V2C DAPLink) shield.
This shield is designed to be used along with the ARM Cortex-M1/M3
DesignStart FPGA reference designs running on the Digilent Arty.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Align all Kconfig option names with LVGL names. The followed rule:
LV_(.*) -> CONFIG_LVGL_(.*).
Also replaced LVGL boolean configuration entries using if/else/endif
with direct IS_ENABLED macro.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Removes redundancy on atmel_rf2xx.overlay message. Clarifies supported
variations section and notes about network on index.rst.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add note about the availability of touch panel IRQ linei when a jumper
in the board is soldered. A Device Tree commented entry has also been
added to ease testing it.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Because the H1 heading was not set in mikroe_eth_click index.rst
file, the shields listing page was listing H2 headings for this
shield.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add devicetree overlay for connecting an Mikroe ETH click shield to an
NXP LPCXpresso55S69 development board.
The LPCXpresso55S69 uses SSEL1 (CS1) for mikroBUS SPI, whereas the
generic Mikroe ETH click board definition assumes SPI CS0.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Replaces .conf type configuration with .defconfig.
Makes configuration conditional, it depends on shield definition and
networking.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
The current shield version shows different configuration, including
disabling default ethernet and wifi interfaces. To allow easy
connection from standard headers, this add two new shield designations.
The existing boards overlays and defconfig were updated.
The documentation was update to reflect changes. A new supported
variations section helps to understand what shield variation user need
select to build their own system.
This changes requires changes on esp32 offload tests to reflect new
esp_8266 shield designations. Sam4e_xpro was keeped as the only one
with dedicated overlay and both frdm_k64f and disco_l475_iot1 were
moved to use standard arduino r3 header using extra args.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The Atmel RF2xx module shield is a generic solution to enable any Atmel
AT86RF2xx IEEE 802.15.4 transceiver. This module enables IEEE 802.15.4
RF2xx Zephyr driver.
The Atmel RF2xx module shield enables any board with an Atmel Xplained,
Xplained-Pro, Arduino or MikroBus expansion header to connect to
networks operation with IEEE 802.15.4, OpenThread or any other stack
based on this media type.
The Atmel RF2xx module is configured to allow interoperate with other
medias like Ethernet. User need configure network stack properlly.
Fixes#26259.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Since commit 5963ebaf33
("drivers: spi: CS configuration through devicetree")
the SPI GPIO CS flags are obtained from DT,
but the patch series has missed the necessary changes
in the device trees for displays and link_board_eth.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add devicetree overlay for connecting an Mikroe ADC click shield to an
NXP LPCXpresso55S16 development board.
The LPCXpresso55S16 uses SSEL1 (CS1) for mikroBUS SPI, whereas the
generic Mikroe ADC click board definition assumes SPI CS0.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Use the recently introduced mikrobus_spi devicetree node as parent node
instead of relying on mapping for arduino_spi.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Fixes whitespace in the frdm_kw41z shield document to allow continuation
in the numbered list of Bluetooth controller instructions and to format
the jumper configuration sublist correctly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Armando Visconti