This code path for returning from an exception wasn't
updating ERET with ESF->pc, resulting in any updates to
the PC by the fault handler being ignored.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Fixed the RTC interrupt masking issue on Deep Sleep entry by
explicitly unmasking it on Deep Sleep exit sequence.
Re-oredered the SoC power states such that SYS_POWER_STATE_CPU_LPS is
the lowest possible Low Power State(LPS) and SYS_POWER_STATE_CPU_LPS_2
is the highest possible Low Power State(LPS). This is need to maintain
the LPS state consistency across different architectures.
Also re-mapped the Low Power States and Deep Sleep States as per
Quark SE C1000 data sheet document under Power Management section.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
add nsim soc support, two configs are contained
* em with arc MPUv2
* em with arc SecureShield and MPUv3
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The entry point can and therefore should be set by linker
scripts. Whenever possible one should express things in the source
language, be it .c or .ld, and not in code generators or in the build
system.
This patch removes the flag -eCONFIG_KERNEL_ENTRY from the linker's
command line and replaces it with the linker script command
ENTRY(CONFIG_KERNEL_ENTRY)
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Also fix the 'default' on XIP. Due to Zephyr's prefer-later-defaults
behavior, it was always set to 'y' (when the dependencies were
satisfied).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Both variables were used (with the same value) interchangeably
throughout CMake files and per the discussion in GH issue,
ZEPHYR_BASE is preferred.
Also add a comment with explanation of one vs. the other.
Tested by building hello_world for several boards ensuring no errors.
Fixes#7173.
Signed-off-by: Alex Tereschenko <alext.mkrs@gmail.com>
This symbol was removed by commit 17c6456678 ("drivers/uart: Use dts
to set uart priorities for QMSI driver"). The setting should come from
DTS now.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The NSIM symbol was removed in commit 9bc69a46fa ("boards: Update arc
em_starterkit support from 2.2 to 2.3").
Guess that UART_NSIM should be used here now, similar to what was done
in commit 45221a9706 ("serial: nsim: Fix impossible-to-enable
CONFIG_UART_NSIM").
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
* re-use top of isr stack as exception stack
* bug fixes in irq offload's implementation
* improve kernel oops implementation
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
This commit improves the reset of arc:
* make the processor in the correct status
* clear interrupt related regs
this may improve or fix#6515
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Whether it should hang the system it not decided finally.
But remove it here to let some tests pass.
Fixes#8032
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* use a separate stack for exception handling, this
will gurantee the exception handling always work, not
affected by some speical cases, e.g., stack check exception
or mem. protection exception at the exception entry.
* this commit can fix the second case of #8092
* note: the thread switch is still possible in exception
handling, e.g, caused by thread_abort. But the switched out
thread cannot be recovered, as the thread context is not
setup.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The original implementation of CONFIG_THREAD_MONITOR would
try to leverage a thread's initial stack layout to provide
the entry function with arguments for any given thread.
This is problematic:
- Some arches do not have a initial stack layout suitable for
this
- Some arches never enabled this at all (riscv32, nios2)
- Some arches did not enable this properly
- Dropping to user mode would erase or provide incorrect
information.
Just spend a few extra bytes to store this stuff directly
in the k_thread struct and get rid of all the arch-specific
code for this.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
ARC has only 2 priorities, 0 or 1. So let's set the right priority for
WDT.
It looks like some commit has changed that, somewhere. And wrong
priorities were lurking around.
Fixes#8096
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
* the original stack check codes have no consideration
for userspace case. This will wrong cause possible stack
check exception.
* this commit refactors the arc stack check support to
support the usperspace.
* this commit fixes#7885. All the failed tests in #7885
are run again to verify this commit. The test results are ok
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
For user thread, the stack check parameters will cover both
user stack part and privilege stack part. Because in arc, they
are in the same array.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Previously the directory core/mpu/ was getting included on a hidden
kconfig. Now this has been replaced with the Kconfig
CONFIG_ARC_CORE_MPU.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
soc.h had defines for CONFIG_ARCV2_TIMER1_INT_{LVL,PRI}. These defines
are both not used and no Kconfig symbols so lets remove them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In preparation for introducing a warning.
Unquoted string defaults work through a quirk of Kconfig (undefined
symbols get their name as their string value), but look confusing. It's
done inconsistently now too.
Suggested by Kumar Gala.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The metairq feature exposed the fact that all of our arch code (and a
few mistaken spots in the scheduler too) was trying to interpret
"preemptible" threads independently.
As of the scheduler rewrite, that logic is entirely within sched.c and
doing it externally is redundant. And now that "cooperative" threads
can be preempted, it's wrong and produces test failures when used with
metairq threads.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
* blink, fp should not be always cleared
* clean up code format
* use a better way to save and restore ER_SEC_STAT
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* current codes use a faked interrupt return to do a thread switch
in exception return.
* so the different between exception return and interrupt return
should be carefully considered.
* when secure is enabled, the sec_stat should also be pushed in
exception entry.
* when secure is enabled, SEC_STAT.IRM must be configured corrrectly
for interrupt return.
* For the case of faked interrupt return in exception return, the
correct value of SEC_STAT.IRM comes from ER_SEC_STAT.ERM.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Fix the qmsi i2c driver and the relevant SoCs accordingly.
Also applying relevant changes on quark_se_c1000_ss as it can use i2c
qmsi driver as well along with qmsi ss i2c driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix the ns16550 uart driver and relevant SoCs accordingly.
All generic settings are now DTS based.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix the qmsi uart driver and relevant SoCs accordingly.
Also: using config for irq everwhere relevantly and not an hardcoded
value in the driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Get the name generated through dts as well.
Fix the rtc driver and relevant SoCs accordingly.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Normally a syscall would check the current privilege level and then
decide to go to _impl_<syscall> directly or go through a
_handler_<syscall>.
__ZEPHYR_SUPERVISOR__ is a compiler optimization flag which will
make all the system calls from the arch files directly link
to the _impl_<syscall>. Thereby reducing the overhead of checking the
privileges.
In the previous implementation all the source files would be compiled
by zephyr_source() rule. This means that zephyr_* is a catchall CMake
library for source files that can be built purely with the include
paths, defines, and other compiler flags that all zephyr source
files uses. This states that adding one extra compiler flag for only
one complete directory would fail.
This limitation can be overcome by using zephyr_libray* APIs. This
creates a library for the required directories and it also supports
directory level properties.
Hence we use zephyr_library* to create a new library with
macro _ZEPHYR_SUPERVISOR_ for the optimization.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
it seems regular expresssion is not supported in "source xxx" after
latest changes in build system.
So explictly list all def config
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* add gpio, i2c, spi definitions
* optimize and bug fix the dts.fixup
* optimize and bug fix the em_starterkit related definitions
in dts folder
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The original em7d, em9d and em11d are different configurations of
em_starterkit. They have the same peripherals, e.g. uart, spi, gpio
, ddr. The differences of them are in arc core configurations, interrupt
number assignment.
So em7d, em9d and em11d can be viewed in the same SoC family or SoC
series.
Referring other arch's implementation, this commit merges em7d, em9d
and em11d into the same SoC, named snps_emsk. This will eliminate
unnecessary duplication and make it easier for future maintainment.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Until now, Zephyr has used a patched Kconfiglib that turns 'source' into
a globbing source (by replacing 'source' with 'gsource' at the token
level). There's two problems with this:
- The patch needs to be maintained separately
- Misspelled filenames are silently ignored, as they look like glob
patterns that don't match anything
Fix it as follows:
1. Replace all 'source' statements that use wildcards with 'gsource'
2. Remove the custom Kconfiglib patch so that 'source' no longer globs
The sed pattern '/source.*[*?]/s/source/gsource/' was run over all
Kconfig* files to do the replacement.
source's that use environment variables that might contain glob patterns
were manually changed to gsource.
Building the docs in doc/ is a good test, as doc/Makefile deliberately
sets the environment variables to glob up as many Kconfig files as
possible.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
* call the _check_stack_sentinel in unnested isr
return.
* for firq, _check_stack_sentinel is called in kernel
isr stack because the limitation of banked register
* for normal irq, _check_stak_sentinel is called in
the interruptted thread stack
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* For STACK_CANERY, the processor should not hang
* as _SysFatalErrorHandler is always executed in
isr context, so remove k_is_in_isr
* the function should return after k_thread_abort
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The original exception handling has space to optimize and
and some bugs need to be fixed.
* define NANO_ESF
* add the definition of NANO_ESF which is an irq_stack_frame
* add the corresponding codes in exception entry and handler
* remove _default_esf
* implement the _ARCH_EXCEPT
* use trap exception to raise exception by kernel
* add corresponding trap exception entry
* add _do_kernel_oops to handle the exception raised by
_ARCH_EXCEPT.
* add the thread context switch in exception return
* case: kernel oops may raise thread context switch
* case: some tests will re-implement SysFatalHandler to raise
thread context switch.
* as the exception and isr are handled in kernel isr stack, so
the thread context switch must be in the return of exception/isr
, and the exception handler must return, should not be decorated
with FUNC_NORETURN
* for arc, _is_in_isr should consider the case of exception
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Add support for getting some basic params from the DTS for the UART.
The ns16550 driver still needs to be updated to get IRQ and address
info from DTS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all ARC SoCs we can remove code associated with !HAS_DTS and
select HAS_DTS at the architecture level.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add initial device tree support for the em{7,9,11}d SoC and associated
em_starterkit boards. The device tree at this point specifies cpu core,
memory, interrupt controller, uart's and i2c controllers.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that dts i2 qmsi ss nodes generate the right options, let's use
them. Apply the relevant fixup on the targeted SoC.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Andrew Boie