Current STM32 SoC initialization code sets really weird startup values
to SystemCoreClock. It should be consistent with Reference Manuals after
this change.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Include low level random generator header in case stm32 random number
generator should be used by entropy driver
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
Enable USB OTG support for olimex stm32-e407 and stm32f407g_disc1
boards by adding USB OTG to the pinmux table. Also, fix out of
range endpoint addresses in CDC ACM case for STM32F4 based boards.
Signed-off-by: Sudarsana Nagineni <sudarsana.nagineni@intel.com>
The exticrX registers were shifted by a word, so configuring
an EXTI line on a port different of PA misconfigured the EXTI line
source and could flood with unwanted events.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Added Inter-IC Sound driver (based on SSC module) for Atmel
SAM MCU family.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-2509
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added DMA (XDMAC) driver for Atmel SAM MCU family. The driver provides
private DMA API to be used by the SAM family device drivers. Public
DMA API to be used by user space programs is currently missing.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1609
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Not all boards require the various binary formats zephyr generates. So
be selective based on the arch, SoC or board and only geenrate the
binaries actually needed.
Fixes#5009
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Unlike other NXP SoCs currently in Zephyr, the mimxrt1052 has the ARM
MPU rather than the NXP MPU. Start out by enabling it with a simple set
of memory regions for "flash" (ITCM), "ram" (DTCM), and the peripheral
buses. More regions will need to be added when we implement support for
external memories.
Tested with:
- samples/mpu/mpu_stack_guard_test
- tests/kernel/mem_protect/protection
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds the mimxrt1052 SoC, which belongs to a new family (nxp_imx) and
series (rt) of SoCs. The mimxrt1052 integrates an Arm Cortex-M7 core,
512 KB TCM, and many peripherals including 2D graphics, an LCD display
controller, camera interface, SPDIF and I2S. Unlike other SoCs in
Zephyr, the mimxrt1052 has no internal flash.
This initial port to mimxrt1052 configures the system clock to operate
at 528 MHz, and enables the serial/uart and gpio interfaces to support
the hello_world and blinky samples. Support for additional Zephyr driver
interfaces will come later.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Add support for nrf52 series SOC. This patch Adds :-
1. Architecture specific Power Management APIs.
2. APIs for invoking various Power Management tasks into nrf52.
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
Remove defines for IRQs we don't use. We should be getting this from DT
so this gives us a list of what we need to cleanup. Remove various
memory address offset defines to the ones we actually use.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This should clear up some of the confusion with random number
generators and drivers that obtain entropy from the hardware. Also,
many hardware number generators have limited bandwidth, so it's natural
for their output to be only used for seeding a random number generator.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Some "random" drivers are not drivers at all: they just implement the
function `sys_rand32_get()`. Move those to a random subsystem in
preparation for a reorganization.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The CLOCK_CONTROL config option is already defined in
drivers/clock_control, so there's no need to redefine it in arch/.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Some SOCs (e.g. STM32F0) can map the flash to address 0 and
the flash base address at the same time. Prevent writing to
duplicate flash address which stops the SOC.
Allow Cortex M SOCs to create their own vector table relocation
function.
Provide a relocation function for STM32F0x SOCs.
Fixes#3923
Signed-off-by: Bobby Noelte <b0661n0e17e@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Added I2C bus (TWI) driver for Atmel SAM MCU family. Only
I2C Master Mode with 7 bit addressing is currently supported.
Tested on Arduino Due board.
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Match change we made to how I2C is enabled for other stm32 platforms:
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
STM32 UART driver was using a mix of LL/HAL APIs. This commit removes
calls to HAL API and replaces them with LL APIs. No functional change
have been seen during non regression testing.
But we could note a direct gain of 1Kb of ROM
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Because the mcux shim drivers will soon depend on a clock control
interface, enable the mcux sim clock control driver by default on all
Kinetis SoCs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This is a USB controller driver for STM32F4xx devices using
the STM32 Cube HAL_PCD framework. This has been tested with
the cdc_acm driver on a 96b_carbon board (STM32F401RE).
This is a refactoring of:
usb: usb_dc_stm: Add support for STM32Cube HAL_PCD USB driver
Signed-off-by: Christer Weinigel <christer@weinigel.se>
[daniel.thompson@linaro.org: Removed STM32F40(157) defconfig changes
together with STM32F4Discovery pinmux and defconfig changes, updated
clock settings and pad configuration to match latest mainline]
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
[giannis.damigos@gmail.com: Change uint*_t types to u*_t types,
change SYS_LOG_USB_DC_STM_LEVEL to SYS_LOG_USB_DRIVER_LEVEL and
update pinmux to match latest arm branch]
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
The Silicon Labs EFM32 Wonder Gecko MCU includes:
* Cortex-M4F core at 48MHz
* up to 256KB of flash and 32KB of RAM
* USB with host and OTG support
* multiple low power peripherals
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use the define generated by the DTS instead of using the FLASH_ALIGN
alias. The latter is an internal mcuboot name. We shouldn't need it in
Zephyr itself.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This workaround fixes the issue that, after pin reset, RESETREAS bits
other than RESETPIN might also be set.
The workaround was added to both nRF52832 and nRF52840 SoCs.
Signed-off-by: Thiago Silveira <thiago@exati.com.br>
802.15.4 is the networking hardware available in KW41Z SoC (and
supported by Zephyr). So, if networking in enabled, automatically
select the corresponding driver. This is similar to how frdm_k64f
automatically selects Ethernet driver, 96b_carbon selects BLE/IPSP
drivers, etc. (But we apply it on SoC level to reuse across the
boards.)
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Some our Zephyr tools don't like seeing UTF-8 characters, as reported in
issue #4131) so a quick scan and replace for UTF-8 characters in .rst,
.h, and Kconfig files using "file --mime-encoding" (excluding the /ext
folders) finds these files to tweak.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
SoCs outside the Kinetis family can have the TRNG module, so move the
HAS_TRNG config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the RNGA module, so move the
HAS_RNGA config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the FTM module, so move the
HAS_FTM config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Note that 'select HAS_FTM' was previously missing from Kconfig.soc and
is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Ilya Tagunov