The CLOCK_CONTROL config option is already defined in
drivers/clock_control, so there's no need to redefine it in arch/.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Some SOCs (e.g. STM32F0) can map the flash to address 0 and
the flash base address at the same time. Prevent writing to
duplicate flash address which stops the SOC.
Allow Cortex M SOCs to create their own vector table relocation
function.
Provide a relocation function for STM32F0x SOCs.
Fixes#3923
Signed-off-by: Bobby Noelte <b0661n0e17e@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Added I2C bus (TWI) driver for Atmel SAM MCU family. Only
I2C Master Mode with 7 bit addressing is currently supported.
Tested on Arduino Due board.
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Match change we made to how I2C is enabled for other stm32 platforms:
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
STM32 UART driver was using a mix of LL/HAL APIs. This commit removes
calls to HAL API and replaces them with LL APIs. No functional change
have been seen during non regression testing.
But we could note a direct gain of 1Kb of ROM
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Because the mcux shim drivers will soon depend on a clock control
interface, enable the mcux sim clock control driver by default on all
Kinetis SoCs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This is a USB controller driver for STM32F4xx devices using
the STM32 Cube HAL_PCD framework. This has been tested with
the cdc_acm driver on a 96b_carbon board (STM32F401RE).
This is a refactoring of:
usb: usb_dc_stm: Add support for STM32Cube HAL_PCD USB driver
Signed-off-by: Christer Weinigel <christer@weinigel.se>
[daniel.thompson@linaro.org: Removed STM32F40(157) defconfig changes
together with STM32F4Discovery pinmux and defconfig changes, updated
clock settings and pad configuration to match latest mainline]
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
[giannis.damigos@gmail.com: Change uint*_t types to u*_t types,
change SYS_LOG_USB_DC_STM_LEVEL to SYS_LOG_USB_DRIVER_LEVEL and
update pinmux to match latest arm branch]
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
The Silicon Labs EFM32 Wonder Gecko MCU includes:
* Cortex-M4F core at 48MHz
* up to 256KB of flash and 32KB of RAM
* USB with host and OTG support
* multiple low power peripherals
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use the define generated by the DTS instead of using the FLASH_ALIGN
alias. The latter is an internal mcuboot name. We shouldn't need it in
Zephyr itself.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This workaround fixes the issue that, after pin reset, RESETREAS bits
other than RESETPIN might also be set.
The workaround was added to both nRF52832 and nRF52840 SoCs.
Signed-off-by: Thiago Silveira <thiago@exati.com.br>
802.15.4 is the networking hardware available in KW41Z SoC (and
supported by Zephyr). So, if networking in enabled, automatically
select the corresponding driver. This is similar to how frdm_k64f
automatically selects Ethernet driver, 96b_carbon selects BLE/IPSP
drivers, etc. (But we apply it on SoC level to reuse across the
boards.)
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Some our Zephyr tools don't like seeing UTF-8 characters, as reported in
issue #4131) so a quick scan and replace for UTF-8 characters in .rst,
.h, and Kconfig files using "file --mime-encoding" (excluding the /ext
folders) finds these files to tweak.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
SoCs outside the Kinetis family can have the TRNG module, so move the
HAS_TRNG config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the RNGA module, so move the
HAS_RNGA config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the FTM module, so move the
HAS_FTM config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Note that 'select HAS_FTM' was previously missing from Kconfig.soc and
is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the ADC16 module, so move the
HAS_ADC16 config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the LPSCI module, so move the
HAS_LPSCI config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the LPUART module, so move the
HAS_LPUART config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
mcuboot_constraints.h had FLASH information related to the SoC that
should be maintained as part of the SoC and not in the subsystem. Also
fixed Makefiles to check for IMG_UTIL Kconfig and not MCUBOOT.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
stm32f417xe and stm32f417xg have been introduced with 2
different defconfig files. Since same code is declared
in both files, mutualize declarations in a single file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The enumerations stm32{f3,f4}x_pin_config_mode aren't used any
more. This patch removes them.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Indenting preprocessor directives reduces the code readability, because
it make preprocessor directives harder to spot.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add flash page layout support for STM32F4 SoCs.
This almost eliminates the need for flash_map.h, except for
STM32F4X_SECTOR_MASK, so delete the file and move the define into the
F4 implementation, to keep things simple.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
When we mask out the GPIO High impedance/Pull-up/Pull-down field we
should be shifting the mask file, not shifting the field. This is
because all the other defines already assume the shift.
Coverity-CID: 173640
Jira: ZEP-2538
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Per ZEP-1958, Phase 2 of adding CC3220sf LaunchXL support,
was to "deprecate the CC3200 launchxl support in Zephyr
(redundant to the CC3220)."
Effectively, the CC3220 SOC replaces the CC3200.
This patch removes the following:
* the imported CC3200 SDK
* CC3200 SOC, board, DTS files.
* adjusts other files where cc3200 was mentioned.
Also, it fixes explicit references to CC3200 in generic
CC32xx driver files.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Previously, calling NVIC_SetPriority(IRQn_Type irqn, ....) with
the NWP interrupt number of 171 caused a hard fault during a
subsequent svc #0 instruction during _Swap().
GNU compiler is generating a bit extension instruction (sxtb) which
converts a positive IRQ value argument to a negative value when
casting to the CMSIS IRQn_Type enum parameter type.
This generates a negative index, which then writes to an SCB
control register instead of NVIC register, causing a hard
fault later on.
This issue only occurs when passing interrupt numbers > 0x80
(eg: 171 (0xab) for the NWP) to the CMSIS NVIC apis.
The solution here is simply to redefine IRQn_Type to be an
unsigned 32 bit integer, while redefining the CMSIS IRQn_Type
enum definitions for interrupts less than zero.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Now that we have an mcux shim driver, remove the old k64-specific
driver. Also remove include/drivers/k20_sim.h, since the old
k64-specific driver was the only thing left using it.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Switches the default pwm driver from the k64-specific driver to the
mcux shim, which can be used on other SoCs with the ftm peripheral.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux ftm driver to adapt it to the Zephyr
pwm interface.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
In the stm32_gpio_flags_to_conf function the configuration
values of the GPIO pin are shifted two times. One in the
stm32-pinctrlf1 header and one in the function. This patch
removes one of those shifts.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The ouput speed of the gpio pins passed via the 'conf' argument was
ignored, causing the speed to always be in its reset state (lowest
possible speed for most pins). This was causing problems for pins that
actually need a speed faster than the default, like the ethernet
controller pins.
Combined with the correct pinmux configuration this fixes problems
of the olimex_stm32_e407 board not being able to send ethernet data.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Carles Cufi