Fixed an issue I2S wouldn't resume when started after a stop
Added code to empty the TX/RX FIFOs upon stop
TX stop is achieved by letting FIFO underrun, then changing state in ISR
RX FIFO is read until empty when RX is stopped
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
This commit adds a new hardware info API.
With this API it is possible to read out the device ID.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
From the driver point of view, monochrome controllers from the ssd16xx
family mostly differ by the amount of row and columns that are
supported. If they support more than 256 rows and/or columns the
corresponding size or position is sent using 2 bytes instead of 1 byte.
This patch therefore adds the width-bits and height-bits DT properties
to make this configurable.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Instead of hardcoding multiple times the display dimensions, use the
values from DT. This still assume 8 rows per page and 8 pixels per
bytes, but that should always be the case for this controller and a
monochrome display.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
STM32 specific behavior "IWDG_STM32_START_AT_BOOT" is enabled
by default. As all vendor specific behavior, this is preferred
to be disabled by default and activated at application level,
so application can have better control of the driver.
For instance watchdog test can't run with this setting.
Disable by default.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use separate bindings for nRF Family SPI Slaves and SPI Masters so that
the properties "csn" and "def-char" can be made required for Slaves
(for Masters such settings are not applicable), and to avoid confusion
between the properties "csn" and "cs-gpios" for Master nodes.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert the HCI SPI driver to get the SPI and GPIO settings from Device
Tree instead of Kconfig. The "zephyr,bt-hci-spi" binding is used as
a common one for this purpose ("st,spbtle-rf" is removed), to take
advantage of the new DT_<COMPAT>_<INSTANCE> generated macros and get
rid of related fixups and aliases.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Clock ISR would callback into the USB driver before it was initialized
and ready to deal with events. This caused a fault.
Statically initialize the fifo to queue events and process them when the
USB device is initialized to avoid the problem.
Signed-off-by: Tom Burdick <thomas.burdick@gmail.com>
Add native_posix USB virtual driver connected over USBIP to the Host
Linux.
Fixes: #9846
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Some defines should have been converted from CONFIG_ to DT_ prefix. For
some reason they got missed in this driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The driver was defining a macro with a CONFIG_ prefix but this wasn't
coming from Kconfig. Change the macro name not to conflict with the
Kconfig CONFIG_ namespace.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The driver was defining a macro with a CONFIG_ prefix but this wasn't
coming from Kconfig. Change the macro name not to conflict with the
Kconfig CONFIG_ namespace.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Its been at least 2 releases since we marked a number of watchdog APIs
as deprecated. Lets remove them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If status is 0, both ip_hdr and proto_hdr will own a pointer to the
relevant IP and Protocol headers. In order to know which of ipv4/ipv6
and udp/tcp one will need to use respectively net_pkt_family(pkt) and
net_context_get_ip_proto(context).
Having access to those headers directly, many callbacks will not need
to parse the packet again no get the src/dst addresses or the src/dst
ports. This will be change after this commit.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Use the new API where relevant. Only sam_gmac is left aside for now.
This simplifies a lot the code as the caller should only care about
allocating net_pkt and its buffer once, and thus will not need to mess
with "frags" etc...
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Use auto-generated device tree macros in LPS25HB driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LSM6DS0 driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Convert usb_dc_stm32 driver GPIO disconnect to use new defines so we
can remove the dts_fixup.h code for it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We have moved GPIO info to DT so the Kconfig symbols for GPIO lines
aren't used anymore. We can just remove them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
1. Fix trailing comment for DT_USBHS_MAXIMUM_SPEED
2. Fix missed CONFIG_USB_HS_BASE_ADDRES that should be
DT_USB_HS_BASE_ADDRESS
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This board is unmaintained and unsupported. It is not known to work and
has lots of conditional code across the tree that makes code
unmaintainable.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Force Operation Mode Strap Override register to disable NANDTree. This
is due to some users reporting PHY entering NANDTree.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Boot PHY initialization timeout, caching mechanism fixes and networking
buffer descriptors moved to no cache section. Enabled cache management
in networking driver and manual barriers.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
We use DT to get the I2C address, so the define that got it from a
Kconfig sybmol isn't used and the Kconfig symbol isnt defined. Remove
this dead code.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since the lp3943 led driver still supports both DTS and non-DTS
configuration, we update the code to use DT_<COMPAT>_<INSTANCE>
defines for the CONFIG_HAS_DTS_I2C case.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Sathish Kuttan