Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
ESP32 can sport up to 4 network interfaces: two 802.11 (station and
ap), ethernet, and bluetooth. All of them derive from the same RDATA
register in efuse block 0. However, in most cases, the last (sixth)
octet will change like so:
- 802.11 station: mac[5] += 0
- 802.11 ap: mac[5] += 1
- bluetooth: mac[5] += 2
- ethernet: mac[5] += 3
Read "Number of universally admnistered MAC address" section in esp-idf
documentation[1] for more information.
[1] https://docs.espressif.com/projects/esp-idf/en/latest/
Signed-off-by: Leandro Pereira <leandro@hardinfo.org>
Add driver support for Atmel SAM0 device ID, which is 16-bytes long.
The device ID can simply be read from memory at a known location, but
the location is only described in the data sheet, not in ASF.
For SAMD2x it's 0x0080A00C, 0x0080A040, 0x0080A044 & 0x0080A048.
For SAMD5x it's 0x008061FC, 0x00806010, 0x00806014 & 0x00806018.
This adds a new property to the device tree to define the device ID
registers for this SoC family.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add driver support for Atmel SAM device ID, which is 16-bytes long. On
this SoC family, the device ID is part of the flash controller and
complex to read. Therefore the driver reads it once at boot time and
then just returned the copy saved in RAM.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Update reserved function names starting with one underscore, replacing
them as follows:
'_k_' with 'z_'
'_K_' with 'Z_'
'_handler_' with 'z_handl_'
'_Cstart' with 'z_cstart'
'_Swap' with 'z_swap'
This renaming is done on both global and those static function names
in kernel/include and include/. Other static function names in kernel/
are renamed by removing the leading underscore. Other function names
not starting with any prefix listed above are renamed starting with
a 'z_' or 'Z_' prefix.
Function names starting with two or three leading underscores are not
automatcally renamed since these names will collide with the variants
with two or three leading underscores.
Various generator scripts have also been updated as well as perf,
linker and usb files. These are
drivers/serial/uart_handlers.c
include/linker/kobject-text.ld
kernel/include/syscall_handler.h
scripts/gen_kobject_list.py
scripts/gen_syscall_header.py
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Use LL drivers instead of HAL driver because LL driver is available
for all soc while HAL driver is not.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
It is planned to deprecate SHELL_CREATE_STATIC_SUBCMD_SET macro
which is replaced by SHELL_STATIC_SUBCMD_SET_CREATE.
Additionally, removed irrelevant comments about alphabetical
ordering which is no longer needed.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The hwinfo shell uses shell functions and thus doesn't build when
CONFIG_SHELL=n. Fix that by adding a dependency on SHELL.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add driver support for kinetis ID device.
The length depends on the SoC.
`SIM_GetUniqueId` was not used because the struct would reorder
the ID and makes the driver more complicated because the length
of the struct depends on the SoC.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commit adds support for device id shell command.
Example:
uart:~$ hwinfo devid
Length: 12
ID: 0x1b0320d51485330313420
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commit adds a new hardware info API.
With this API it is possible to read out the device ID.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Kumar Gala