This https-client sample starts to send HTTP GET/HEAD/POST
requests same way as http-client, to https server that can
be found in net-tools repository.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Various network samples contained QEMU slip setup instructions
or those instructions were missing. A reference doc in
doc/subsystems/networking/qemu_setup.rst file already has the
setup instructions for QEMU. So add a reference to that file
in samples/net/*/README.rst files and remove unnecessary slip
setup instructions in relevant files.
Fix various typos in readme files at the same time.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The sample app "static_lib" is very important to Zephyr user, which
demonstrate how to build and link a static lib.
ISSM team wanted to integrate this app in their IDE for quark platforms.
However they find the in "static_lib/hello_world/Makefile" BOARD is
hardcoded as qemu_x86.
This patch supports other BOARD passed from build command.
I have verified this app working fine @Arduino101.
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
Add clarification that the DNS server configuration must be edited in
the respective prj.conf file.
JIRA: ZEP-2040
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The STM32F412 has PWM output capabilities. Add support to the blink_led
samples.
Tested using a Nucleo STM32F412ZG board (PWM output on pin 28 of the
CN11 Morpho connector and pin 29 of the CN10 Zio connector).
Change-Id: I75fb986fa97bd1c07c6375938430e7963297cd9d
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
The STM32F413 has PWM output capabilities. Add support to the blink_led
samples.
Tested using a Nucleo STM32F413ZH board (PWM output on pin 28 of the
CN11 Morpho connector and pin 29 of the CN10 Zio connector).
Change-Id: I3b25b09cab54265b28088ac9681aec588d9d48b5
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
The number of RX and TX buffers is increased to 64 as the
earlier limit can cause memory exhaust in some cases.
Jira: ZEP-2223
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This fix is basically a no-op as the rx_buf pointer cannot be null
in practice, but in order to avoid Coverity complaining about
it add some null pointer checks to the UDP handling code.
Coverity-CID: 170124
Jira: ZEP-2235
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of NULL terminated buffer arrays, let's add a parameter for each
that tells the number of spi_buf in it.
It adds a little bit more complexity in driver's side (spi_context.h)
but not on user side (bufer one has to take care of providing the NULL
pointer at the end of the array, now he requires to give the count).
This will saves a significant amount of bytes in more complex setup than
the current dumb spi driver sample.
Fix and Use size_t everywhere (spi_context.h was using u32_t).
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Waiting for an NET_EVENT_IF_UP before trying to connect isn't sufficient
in some cases; for instance, on devices using the MCUX HAL, such as the
FRDM-K64F, the interface will have the NET_IF_UP flag set even though
the link negotiation didn't yet complete.
Executing this sample on such board will produce the following output.
Notice the "Enabled 100M..." message right after trying to connect.
[dev/eth_mcux] [DBG] eth_0_init: MAC 00:04:9f:6f:91:da
net_context_connect error Is the server (broker) up and running?
[publisher:247] network_setup: -60 <ERROR>
Bye! [dev/eth_mcux] [INF] eth_mcux_phy_event: Enabled 100M
full-duplex mode.
Even though the returned error is ETIMEDOUT, increasing
net_context_connect()'s timeout parameter to several seconds isn't
sufficient; other steps performed by network_setup() after the link has
been fully established are necessary. As a stopgap measure, try
connecting a few times before giving up (more than one connection
attempt should be made by application in most cases, anyway.)
It might be the case that we need events to monitor ethernet link
(re)negotation in addition to the NET_IF_UP bit.
Jira: ZEP-2036
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The state machine of the game assumes that the user needs to
explicitly re-select multiplayer game when disconnected. We need to
therefore make sure that advertising stays off as soon as the first
connection happens.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Occasionally the sound might stay enabled for the restart timeout (2
seconds) if the ball would hit the wall right before missing the
paddle. Ensure that it's disabled whenever the game ends.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If the HTTPS connection is closed, then properly handle call to
HTTP parser init in case of error and also remove any pending
data that belong to old connection.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The buttons on the microbit cause quite easily "ghost" key presses.
Add a simple filter that ignores button presses from the same button
that happen less than 100ms from each other.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The stuff that the GPIO button callback does (in particular the printk
calls) requires more stack space from the ISR stack. Increase it to 1k
from the default 640.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This enabled testing CONFIG_BLUETOOTH_SHELL with configuration other
than btshell and enables ipsp sample to use bt shell module which
allows to disconnect, print metrics, etc.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch add arm core MPU support to NXP MPU driver.
With this feature it is now possible to enable stack guarding on NXP
MPUs.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Add beeps whenever the ball hits the walls or the paddle. Requires a
piezo buzzer connected to pin 0.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add initial draft of a pong game using the display on the micro:bit
and its two buttons. This draft only supports a solo game where the
ball bounces from the "roof" and lets the player play against himself.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This gives a quicke example on how to use SPI asynchronous calls with
kernel's k_poll API.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Adding a struct k_poll_signal parameter to driver's API unique
exposed function.
If not NULL, the call will be handled as asynchronous and will
return right after the transaction has started, on the contrary
of current logic where is waits for the transaction to finish
(= synchronous).
In order to save stack, let's move the device pointer to struct
spi_config. So the call is still at a maximum of 4 parameters.
Adapting spi_dw.c and spi driver sample to the change so it still
builts.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This application intents to test an SPI driver by looping over MISO/MOSI
line where the controller will then send data to itself.
It will test various buffer tx/rx schemes.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There is not enough memory to run the HTTP server sample
application in Arduino-101 so remove the config file.
Jira: ZEP-2157
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This patch add a controller specific write function and fixes a
documentation error in the mpu_test README file.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds the mpu_stack_guard_test to the available samples.
The purpose of this test is to exercize the thread stack guard enabled
via MPU on arm platforms.
Change-Id: I4665a20956d9e6d0dd4b5cc862e82040a53afafc
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds the Thread Stack Guards configuration option to the
synchronization sample.
This is meant to be an easy way to prove that the MPU can be dynamically
programmed on the supported platforms.
Change-Id: I77fbe6af3303ff8a2904768abd4cc9797f03c092
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Rename SOC_STM32L476XX to SOC_STM32L476XG to keep flash
size information.
Aim is to be able to distinguish flash size variants of
the SoC when needed (for instance in dts/arm/st/mem.h file)
Change-Id: I834bb5b83c24c39e90c0492a2b22a7c7802de361
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Sometime it is observed on the Arduino 101 that when we write more than
4 bytes into TX USB Endpoint, first 4 bytes are getting repeated
(frequency of occurrence ~1/3000).
This patch does following :-
1. In sample application "cdc_acm", it adds capability to
handle partial transfer data incase data is transferred partially
if exceeds maximum data transfer size.
2. It restricts write of more than 4 bytes into TX USB Endpoint.
This is work around to avoid issue occarance.
Jira: ZEP-2074
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit creates a HTTP server library. So instead of creating
a complex HTTP server application for serving HTTP requests, the
developer can use the HTTP server API to create HTTP server
insteances. This commit also adds support for creating HTTPS servers.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Jukka Rissanen