Trims the default memory configuration for the BBC Microbit in mesh
samples to ensure that it fits.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Allocates segmented message buffers as slabs in a common pool for RX and
TX. This reduces memory requirements for both TX and RX, as TX messages
can be stored without the network and advertising buffer overhead, and
RX can use only the slabs it needs, instead of allocating a full size
segmented message. This approach also removes the need for decrypting
the segments for each retransmission, reducing overall processing load.
Slab based segmentation for tx also introduces queuing of segmented
messages, which allows the application layer to send multiple messages
to the same destination without violating Bluetooth Mesh specification
v1.0.1, section 3.6.4.1. This mechanism is provided through a flag that
blocks segmented messages to a destination which a message is already
being sent to until the previous message finishes.
This changes the SDU size configuration to a symmetrical
RX_SEG_MAX/TX_SEG_MAX pair of configurations, plus a new segment pool
side configuration. It also removes the binding between the TX_SEG_MAX
config and the advertising buffers, reducing the minimum advertising
buffer count from 6 to 3.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Split Link Layer implementation uses 80 bytes more ISR stack
in comparison to Legacy Link Layer, hence increase the
required ISR_STACK_SIZE for the BBC micro:bit and other
nRF51 QFAA SoC based mesh and mesh_demo samples.
Fixes#20414.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Tick rate is becoming a platform tunable in the tickless world. Some
apps were setting it due to requirements of drivers or subsystems (or
sometimes for reasons that don't make much sense), but the dependency
goes the other way around now: board/soc/arch level code is
responsible for setting tick rates that work with their devices.
A few tests still use hard-configured tick rates, as they have
baked-in assumptions (like e.g. "a tick will be longer than a
millisecond") that need to be addressed first.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Introduce a separate buffer pool for events which the HCI driver
considers discardable. Examples of such events could be e.g.
Advertising Reports. The benefit of having such a pool means that the
if there is a heavy inflow of such events it will not cause the
allocation for other critical events to block and may even eliminate
deadlocks in some cases.
Also update all mesh samples not to specify explicit RX buffer counts
anymore. Instead, create appropriate defaults in Kconfig so that we
only need to override this in the app for cases like the bbc:microbit
with limited memory.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds common option to disable support for LE Data Length Update
procedure in controller and host.
This will reduce flash usage by compiling out le_data_len_change
event handler that will never be called if controller has been
compiled with BT_CTLR_DATA_LENGTH option disabled.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
This adds common option to disable support for PHY Update
procedure in controller and host.
This will reduce flash usage by compiling out le_phy_update_complete
event handler that will never be called if controller has been
compiled with BT_CTLR_PHY option disabled.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
Minimal driver for ILI9340 LCD display driver including support
for adafruit 2.2" LCD display (1480)
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
Instead of having an RPL-specific storage timer, introduce a generic
one that'll eventually be used for all persistent storage.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Trond Einar Snekvik