Use a kbuild trick to force built-in.o to get built even if there isn't
any code so we can link properly. This is cleaner than keeping around
files that don't do anything.
We keep around board.h for now since drivers and other code might expect
it to exist.
Change-Id: I1ed09f05ea2c2d08d11fc742d76f32c1f8f2fbbd
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert leading whitespace into tabs in Kconfig files. Also replaced
double spaces between config and <prompt>.
Change-Id: I341c718ecf4143529b477c239bbde88e18f37062
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This file was misplaced here. Atom board is now available only
for minnowboard.
Change-Id: If5a0d723600f957e2b024848b8cb8aac2e7a7ff9
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
There are two major issues with the kconfig:
() Some of the config options have incorrect dependencies inside help
under menuconfig. For example, CONFIG_GPIO depends on BOARD_GALILEO.
() Since the SoC and board specific kconfig files are parsed first,
the help screen would say, for example, CONFIG_SPI is defined at
arch/arm/soc/fsl_frdm_k64f/Kconfig. This is incorrect because
the actual config is defined in drivers/spi/Kconfig.
These cause great confusion to users of menuconfig/xconfig.
To fix these, the SoC and board defaults are now to be parsed last.
Note that the position swapping of defaults in this patch is due to
the fact the the default parsed last will be used.
And, spi_test is broken due to the fact that it requires
CONFIG_SPI_INTEL_PORT_1, but never enables it anywhere. This is
bypassed for now.
Origin: refactored and edited from existing files
Change-Id: I2a4b1ae5be4d27e68c960aa47d91ef350f2d500f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This makes the board selection dependent on SoC selection. For example,
select Atmel SAM3 will only allow "Arduino Due" as board selection.
This disallows incompatible SoC/board combination, like K64F with
Arduino Due.
JIRA: ZEP-106
Change-Id: I675961cf33db5a0058fc68f14c8f16978f9c6b95
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
CONFIG_HPET_TIMER_LEVEL_LOW and CONFIG_HPET_TIMER_RISING_EDGE are
selected from same choice option so cannot be both selected.
Since HPET_TIMER_FALLING_EDGE is the default only options overriding
this were left in defconfig files.
Fix following:
Merging prj_x86.conf
.config:10:warning: override: HPET_TIMER_RISING_EDGE changes choice
state
Change-Id: I5c88d2c0ae309afa11d9fae116235a8a424a2408
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Change terminology and use SoC instead of platform. An SoC provides
features and default configurations available with an SoC. A board
implements the SoC and adds more features and IP block specific to the
board to extend the SoC functionality such as sensors and debugging
features.
Change-Id: I15e8d78a6d4ecd5cfb3bc25ced9ba77e5ea1122f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit also renames boards and makes naming consistent between
board name and defconfig files.
quark_d2000_reference -> quark_d2000_crb
quark_se_test_sss -> quark_se_sss_ctb
quark_se_test -> quark_se_ctb
Change-Id: Ibe6a5102edb987fe1d6ce32c8c392a87d45d6951
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Define boards based on platforms/SoCs and define them under boards/.
Also unify the naming of all platform, SoC and board files and use
platform.h for platforms and board.h for boards.
Change-Id: Icfeb96479ab5800aca98c80a79bdc3cecd645314
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Kumar Gala