So far nRF's TIMER was used for generating PWM signal. Add support for
generating PWM based on RTC, which is sourced by 32KHz low frequency
crystal. This allows to use low frequency PWM with much lower power
consumption, because high frequency clock path can be disabled.
Don't support RTC clock prescaler, because maximum 512s period covers
most use cases. This allows to adjust pulse and period cycles to the
fact that CLEAR task event is generated always one LFCLK cycle after
period COMPARE value is reached.
Also update hal_nordic revision, as it contains updated check for PPI
channels conflict when RTC is used to generate PWM.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Defining a symbol with 'menuconfig' just tells the menuconfig to display
any dependent symbols that immediately follow it in a separate menu.
'menuconfig' has no effect on symbol values.
Making a symbol that doesn't have any dependent symbols after it a
'menuconfig' should be avoided, because then you end up with an empty
menu, which is shown as e.g.
[*] Enable foo ---
This is how it would be shown if there were children but they all
happened to be invisible as well.
With a regular 'config', it turns into
[*] Enable foo
Change all pointless 'menuconfig's to 'config's.
See the section on 'menuconfig' on the Kconfig - Tips and Best Practices
page as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This option determines the name under which the device represented by
the `sw_pwm` node is registered in the system. But when the value of
this option does not match the `label` property of the `sw_pwm` node,
a problem arises when the `sw_pwm` node is referenced by a "pwm-leds"
compatible node, since the `*_PWMS_CONTROLLER` macro that is generated
for this referencing node contains a non-existing device name (as it is
the `label` property value, not the Kconfig option value).
This commit solves the issue described above by removing the Kconfig
option and replacing all of its occurrences in sample applications
by the standard macro generated for the `sw_pwm` node, containing
the value of the `label` property of this node.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
1. Kconfig option Clock prescaler removed.
2. Modified pwm_nrf5_sw.c driver to use DT
defines instead of Kconfig, and also use new
DT options (timer, ppi/gpiote, etc).
3. Cleanup some code.
Signed-off-by: Gaute Gamnes <gaute.gamnes@nordicsemi.no>
- Remove redundant dependencies on the PWM symbol (which show up as
PWM && PWM in the documentation). The 'source's in
drivers/pwm/Kconfig are already within an 'if PWM' block.
- Turn some repeated 'depends on FOO' into 'if FOO' blocks.
- Turn some 'if FOO's that surround a single symbol into
'depends on FOO'.
'if FOO' is equivalent to adding a 'depends on FOO' to each symbol
within the 'if'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Enable HW PWM driver instead of the SW one on nRF SoCs where the PWM
peripheral is present.
Default PWM instances are also enabled on Nordic DK boards so that it
is possible to build the basic fade_led sample for them without extra
adjustments.
After the above changes are applied, some configuration alterations
in basic samples blink_led and fade_led become no longer needed.
These are removed. And the blink_led sample is corrected so that it
works with the nRF HW PWM driver as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Consistently use
config FOO
bool/int/hex/string "Prompt text"
instead of
config FOO
bool/int/hex/string
prompt "Prompt text"
(...and a bunch of other variations that e.g. swapped the order of the
type and the 'prompt', or put other properties between them).
The shorthand is fully equivalent to using 'prompt'. It saves lines and
avoids tricking people into thinking there is some semantic difference.
Most of the grunt work was done by a modified version of
https://unix.stackexchange.com/questions/26284/how-can-i-use-sed-to-replace-a-multi-line-string/26290#26290, but some
of the rarer variations had to be converted manually.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add support for specifying the clock prescaler value for the HF timer
used for generating the PWM signals. This allows for lower timer
frequency and thus slower PWM signals (e.g. for use as servo
controller).
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Upcoming Nordic ICs that share many of the peripherals and architecture
with the currently supported nRF5x ones are no longer part of the nRF5
family. In order to accomodate that, rename the SoC family from nrf5 to
nrf, so that it can contain all of the members of the wider Nordic
family.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add support for nRF5x series GPIOTE based PWM driver
implementation.
Provides upto 3 pins/channels using one HF timer, two PPI
channels per pin, and one GPIOTE config per pin.
Change-id: I6056b199ec2cff595ba8fea9f659a0338ed4635b
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Marcin Niestroj