These tick computation can take a significant amount of time, and there
is no reason to do them with interrupts locked.
Change-Id: I2d8803ec6025b827e9450fa493084bbf8be98bad
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Use _INACTIVE instead of hardcoding -1.
_EXPIRED is defined as -2 and will be used for an improvement so that
interrupts are not locked for a non-deterministic amount of time while
handling expired timeouts.
_abort_timeout/_abort_thread_timeout return _INACTIVE instead of -1 if
the timeout has already been disabled.
Change-Id: If99226ff316a62c27b2a2e4e874388c3c44a8aeb
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The way the ready thread cache was implemented caused it to not always
be "hot", i.e. there could be some misses, which happened when the
cached thread was taken out of the ready queue. When that happened, it
was not replaced immediately, since doing so could mean that the
replacement might not run because the flow could be interrupted and
another thread could take its place. This was the more conservative
approach that insured that moving a thread to the cache would never be
wasted.
However, this caused two problems:
1. The cache could not be refilled until another thread context-switched
in, since there was no thread in the cache to compare priorities
against.
2. Interrupt exit code would always have to call into C to find what
thread to run when the current thread was not coop and did not have the
scheduler locked. Furthermore, it was possible for this code path to
encounter a cold cache and then it had to find out what thread to run
the long way.
To fix this, filling the cache is now more aggressive, i.e. the next
thread to put in the cache is found even in the case the current cached
thread is context-switched out. This ensures the interrupt exit code is
much faster on the slow path. In addition, since finding the next thread
to run is now always "get it from the cache", which is a simple fetch
from memory (_kernel.ready_q.cache), there is no need to call the more
complex C code.
On the ARM FRDM K64F board, this improvement is seen:
Before:
1- Measure time to switch from ISR back to interrupted task
switching time is 215 tcs = 1791 nsec
2- Measure time from ISR to executing a different task (rescheduled)
switch time is 315 tcs = 2625 nsec
After:
1- Measure time to switch from ISR back to interrupted task
switching time is 130 tcs = 1083 nsec
2- Measure time from ISR to executing a different task (rescheduled)
switch time is 225 tcs = 1875 nsec
These are the most dramatic improvements, but most of the numbers
generated by the latency_measure test are improved.
Fixes ZEP-1401.
Change-Id: I2eaac147048b1ec71a93bd0a285e743a39533973
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The Cortex-M3/4 kernel was reserving priorities 0 and 1 for itself, but
was not registering any exception on priority 0. Only reserve priority 0
and use it for SVC and fault exceptions instead of priority 1.
Change-Id: Iff2405e27fd4bed4e49ab90ec2ae984f2c0a83a6
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
There are now three flags that decide how many priorities are reserved
by the kernel, each one requiring one priority level: Zero Latency
Interrupts, BASEPRI locking (for SVC usage) and faults that are not at
priority -1, so that taking them in an ISR actually triggers the fault
synchronously.
Change-Id: I7f4d760c9110051aeb82dcfd8cd68026a9b74b54
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Cortex-M0/M0+ do not have other faults than the hard fault at priority
-1, so they do not need to reserve a priority to allow exceptions to
trigger during handling of ISRs.
Change-Id: I479e439f7bcac70b4b2b787bcd744a4c65437e80
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This allows using it in _EXC_PRIO() instead of hardcoding 2 and 3.
Change-Id: I3549be54602643e06823ba63beb6a6992f39f776
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Use it to flag which CPUs can do zero latency interrupts, which depend
on being able to lock up to a specific interrupt priority.
Change-Id: I09f71366ea1d05486e38c513a09abc270884879f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Fixes this:
error: ‘zero_addr’ defined but not used [-Werror=unused-const-variable=]
...
Change-Id: I5b0baf597e62f3206e15638a63e129503b76b048
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is a left-over that should have been renamed to the new
net_buf_alloc_debug function name.
Change-Id: Iefcbd2eefab5614b1b80214cb0927f3db77d592e
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When going into DEEP_SLEEP mode, the ARC core now saves
its context. This includes:
- All core registers
- Stack pointer
- Program counter (restored by jumping to the restore code)
The arc reset code now checks if the GPS0 bit 2 is set.
This is similar to the behavior of the x86 core done by
the QMSI bootloader which is setting GPS0 bit 1 in order
to call the restore path instead of cold boot path.
The sample has been adapted in order to support the ARC.
Jira: ZEP-1222
Change-Id: I375f03b16b8a5fd1f07ead55cf7e4947d6290c9f
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
When going into DEEP_SLEEP state, the ARC timer
needs to be restored.
This implements the function to restore the timer
after sleep.
As the time spent during sleep is not currently known,
the timer is expired to reschedule the application task.
Jira: ZEP-1224
Change-Id: I22a30d0fd79f177cf166b9a29dc78d68f7d7fbad
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
In order to resume the ARC from deep sleep,
the interrupts need to be restored.
The FIRQ stack needs to be saved and restored
when performing sleep operations.
During early initialization, the sp in the 2nd register bank
is made to refer to _firq_stack.
This allows for the FIRQ handler to use its own stack.
Fast Interrupts cannot be used after sleep if this information
is not restored.
This patch adds the suspend and resume functions.
Jira: ZEP-1223
Change-Id: Ic81980f05aee6c1f7b8c46c743f2648c65b29486
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Move interrupt initialization for the ARC to its own
device. The init function for the arc will be only
doing platform specific operations
Jira: ZEP-1288
Change-Id: Icb04c3622890021c65cd24cecf6cafee6c37caf9
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Following commit fc21a76db6
Some more fixes are needed.
Change-Id: I19c2c979d44be5edfd76041d3cf4507860795c78
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Using a LIFO instead of a FIFO has the potential benefit that more
recently in-use buffers may be "cache-hot" and therefore accessed
faster than least recently used (which is what we get with a FIFO).
Change-Id: I59bb083ca2e00d0d404406540f7db216742a27cf
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the user data size is now stored in the pool there's very little
value in storing it as well per-buffer.
Change-Id: I17a99123b232423c52a2179b4eccd813728d51b1
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In order to keep the initialization process light-weight, remove
net_buf_pool_init() and instead perform the initialization of the pool
and buffers in a "lazy" manner. This means storing more information
in the pool, and removing any 'const' members from net_buf. Since
there are no more const members in net_buf the buffer array can be
declared with __noinit, which further reduces initialization overhead.
Change-Id: Ia126af101c2727c130651b697dcba99d159a1c76
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is only for use with custom destroy callbacks, so that the
application gets isolated away from the details of how exactly the
buffers are managed. This opens up the possibility of switching away
from k_fifo to potentially better solutions, such as k_lifo.
Change-Id: I0d8322fdec3500d8ae060ae471b9448aeaa4572a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
That bug never got caught because the buffer in unit test is always
clean and fully initialized to 0, and that part of the code being
tested is never used in real as the ACK reply is directly made by the
chip.
Change-Id: I88c4dd3767b4addf2250165b94f49fae29d322ea
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If receiving a malformed MQTT packet with less than 5 bytes it's
possible to get a read one byte behind buf.
Change-Id: I34425add57c937c8fd9df5bf7b72af092d6f5f32
Signed-off-by: Stig Bjørlykke <stig@bjorlykke.org>
Ethernet build-all test was not being filtered base on RAM size so
build step LINK was failing with "region `RAM' overflowed by 192
bytes" error when running daily sanitycheck.
Added filter so this test is not attempted for boards with smaller
RAM such as quark_d2000_crb, which was causing daily build failure
Change-Id: I4ed3bef4f1c78e83890331db34fb1f2b2b066414
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
This reverts commit 7a74fb0454.
This commit breaks the sample. The sample code has a bug which will be
addressed in a separate patch.
Change-Id: Ic44faeafced4415765fded04e2493e306fc35331
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The CONFIG_TEST_RANDOM_GENERATOR parameter is not intended for
production use. Switch to CONFIG_RANDOM_GENERATOR.
Change-Id: Id6ce986259270455223ce6a42d19a3d9c9b1e642
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Restructure the RANDOM Kconfig to match the structure used in other
drivers with a single top level menu. Move the true random number
generators to appear first in the menu, with pseudo generators at the
bottom. Do not present pseudo generators if a true random generator
is presented.
This change implies that tests, samples and applications that require
the random driver interface must now select CONFIG_RANDOM_GENERATOR.
In order for tests and samples to build (and run) on platforms that
have no random driver it remains necessary to select
the CONFIG_TEST_RANDOM_GENERATOR.
Note that CONFIG_TEST_RANDOM_GENERATOR retains its original purpose of
enabling a random driver that delivers non random numbers for the
purpose of testing only.
Change-Id: I2e28e44b4adf800e64a885aefe36a52da8aa455a
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Remove CONFIG_TEST_RANDOM_GENERATOR from each test and sample where it
is not required.
Change-Id: I949f8e93c2cb1881622a5e48efeb87c43122a170
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Update drivers to return INT_PLUS_MICRO values instead of doubles.
This hides the fact that the drivers use floating point operations and
doesn't force the application to use them as well.
Change-Id: I14c6faecb35331c2fdbdab41bc624d751de984b8
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Use integers for sensor value calculations in which doubles are not
required.
Change-Id: I8662023ca596cb232e31849b0b77ae2bf0372cf0
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Remove SENSOR_VALUE_TYPE_INT as it is the same as
SENSOR_VALUE_TYPE_INT_PLUS_MICRO with val2 set to 0.
Change-Id: If5a9c579b7267701c27f40fd887acae47d64edc5
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Remove SENSOR_VALUE_TYPE_Q16_16 as it is not used by any driver. Future
drivers can use any of the remaining value types.
Change-Id: I984143cc65d6a6fd0477f310ac17c62498cc05b8
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Until now it has been necessary to separately define a k_fifo and
an array of buffers when creating net_buf pools. This has been a bit
of an inconvenience as well as blurred the line of what exactly
constitutes the "pool".
This patch removes the NET_BUF_POOL() macro and replaces it with a
NET_BUF_POOL_DEFINE() macro that internally expands into the buffer
array and new net_buf_pool struct with a given name:
NET_BUF_POOL_DEFINE(pool_name, ...);
Having a dedicated context struct for the pool has the added benefit
that we can start moving there net_buf members that have the same
value for all buffers from the same pool. The first such member that
gets moved is the destroy callback, thus shrinking net_buf by four
bytes. Another potential candidate is the user_data_size, however
right not that's left out since it would just leave 2 bytes of padding
in net_buf (i.e. not influence its size). Another common value is
buf->size, however that one is also used by net_buf_simple and can
therefore not be moved.
This patch also splits getting buffers from a FIFO and allocating a
new buffer from a pool into two separate APIs: net_buf_get and
net_buf_alloc, thus simplifying the APIs and their usage. There is no
separate 'reserve_head' parameter anymore when allocating, rather the
user is expected to call net_buf_reserve() afterwards if something
else than 0 headroom is desired.
Change-Id: Id91b1e5c2be2deb1274dde47f5edebfe29af383a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This issue was reported by Coverity
Coverity-CID: 157621
Change-Id: I7f84c0868467ab55e033aecac037967da001a6db
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
As flags are modified when entering sleep, add cc to
clobber list.
Jira: ZEP-1408
Change-Id: Ia80bc1c7ddedb9d9963c47108372a90928597c1d
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Last argument for k_stack_init is of time int resulting in UINT_MAX
being converted to negative value. Instead of UINT_MAX use maximum
possible number of entires that won't result in stack->base and
stack->top overflow.
Change-Id: I8470f6dd18abcccc72590e07e0d0efd4ce2208cc
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Disable MDEF option and set it only in legacy projects.
Change-Id: I2e1f011eb1f876af929140e36f71f0efb5e955c1
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patch does not apply anymore. A patched qemu already exists in the
SDK.
Change-Id: Iee18550a7b9288a1db2a6ecc4378ff554b240229
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Hamming Weight or "popcount" consists in counting the number of bits set
to 1 in a particular word. This commit adds a macro to be able to use
the existing builtin for this purpose with the GCC compiler.
Change-Id: Iec64c19e897de2bc02e981071465bbe230ee9add
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The ARG_UNUSED macro is added to avoid compiler warnings.
Change-Id: Ie9b72c94191318c1d667d7929eb029098c62e993
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
The ARG_UNUSED macro is added to avoid compiler warnings.
Change-Id: If0242548849ee5b258bb3fce9fd727b377411343
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
The ARG_UNUSED macro is added to avoid compiler warnings.
Change-Id: If14c3928a30c8f3156cdcd0fe11e22407a78c088
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Use uint32_t for counters instead of int to avoid compiler warnings.
Change-Id: Ie96dfaca650b5f91562c0740c18610fc40968be6
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
mem_pool structures use uint32_t for counters and size_t
to specify sizes, however some routines in mem_pool.c
make use of int for similar purposes. This commit fixes
that situation by updating some variables to match
mem_pool data types.
Change-Id: I0aa01c27e512d06d40432e8091ed8fd9d959970c
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Applications may want to know how much time is left until a delayed
work gets scheduled. To prevent applications from having to track this
themselves simply use the information that's already embedded as part
of the timer that's part of the delayed work struct.
Change-Id: I189df2f3be8b207e68b554a0cbb4f97f1a99de22
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Factor out the code for evaluating the remaining time for _timeout
structs so that it can also be used for other objects besides k_timer
structs (like k_delayed_work, coming in a subsequent patch).
Change-Id: I243a7b29fb2831f06e95086a31f0d3a6c37dad67
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Benjamin Walsh