The options selecting nRF drivers are now enabled by default when
an nRF SoC is selected as the build target.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert lsm9ds0_gyro driver to get the device name as well as
i2c slave information and gpio info for triggers from device tree.
Updates the build_all test accordingly.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lsm9ds0_mfd accel/magn driver to get the device name as well
as i2c slave information from device tree. Updates the build_all
test accordingly.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lis2mdl magnetometer driver to get the device name as well
as i2c slave information from device tree. Updates the build_all
test accordingly.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lis3dh accelerometer driver to get the device name as well
as i2c slave information from device tree. Updates the build_all
test accordingly.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lis2dh accelerometer driver to get the device name as well
as i2c/spi slave information from device tree. Updates the build_all
test accordingly. (issue #11605)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
poll_out function was returning the character that was sent. It
happens that it is always constant and the return of this functions is
never tested. Changing it to be a void function.
MISRA-C rule 17.7
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The memory slabs used for I2S are used through DMA. In case the CPU has
a cache, we need to ensure minimum alignment so that an entire number of
cache lines can be cleaned or invalidated.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Now all tests are additionally run in user mode.
Test now all use the i2s_buf_read/write APIs, which
are themselves implemented in terms of i2s_read/write.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Converts the adxl362 sensor driver to get the device name and spi slave
properties from the device tree rather than Kconfig. Updates the
build_all test accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Rewritten Xtensa CCOUNT driver along the lines of all the other new
drivers. The new API permits much smaller code.
Notably: The Xtensa counter is a 32 bit up-counter with a comparator
register. It's in some sense the archetype of this kind of timer as
it's the simplest of the bunch (everything else has quirks: NRF is
very slow and 24 bit, HPET has a runtime frequency detection, RISC-V
is 64 bit...). I should have written this one first.
Note also that this includes a blacklist of the xtensa architecture on
the tests/driver/ipm test. I'm getting spurious failures there where
a k_sem_take() call with a non-zero timeout is being made out of the
console output code in interrupt context. This seems to have nothing
to do with the timer; I suspect it's because the old timer drivers
would (incorrectly!) call z_clock_announce() in non-interrupt context
in some contexts (e.g. "expiring really soon"). Apparently this test
(or something in the IPM or Xtensa console code) was somehow relying
on that on Xtensa. But IPM is a Quark thing and there's no particular
reason to run this test there.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert the BMI160 to use Device Tree to get SPI and GPIO params instead
of Kconfig. Updated samples, tests, and arduino_101_sss board support
for this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When using an IDE (e.g. Eclipse, Qt Creator), the project name gets
displayed. This greatly simplifies the navigation between projects when
having many of them open at the same time. Naming every project "NONE"
defeats this functionality.
This patch tries to use sensible project names while not duplicating
too much of what is already represented in the path. This is done by
using the name of the directory the relevant CMakeLists.txt file is
stored in. To ensure unique project names in the samples (and again, in
the tests folder) folder, small manual adjustments have been done.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
test application of watchdog assumes that the variable
created in noinit section will have initial value as
zero. This is an incorrect assumption as variable
in noinit section can have any value. The application
is modified work even if variable in noint section
have any value.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Add default dts configuration for CI tests in case
selected board used for test purpose do not export
dts configuration for LIS2MDL
Signed-off-by: Mario Tesi <mario.tesi@st.com>
Added support to LIS2MDL Magnetometer sensor provided
with following features:
- I2C interface
- Mag data
- Temperature data
- ODR configurable by config or at runtime
- Trigger mode selectable by menuconfig
- IRQ pin configurable (by dts or Kconfig)
- Hard Iron offset setting at runtime
- Include yaml file
Tested on ST MEMS IKS01A2 + NUCLEO STM32F411RE board.
LIS2MDL connected to I2C master interface (SPI 3 wire not
supported yet).
Test run with all ODR {10, 20, 50, 100} Hz in poll and
trigger mode.
GPIO IRQ dts configuration has been tested by adding
to boards/arm/nucleo_f411re/nucleo_f411re.dts file
this patch:
&i2c1 {
status = "ok";
clock-frequency = <I2C_BITRATE_FAST>;
+
+ /* ST Microelectronics LIS2MDL mag sensor */
+ lis2mdl-magn@1e {
+ compatible = "st,lis2mdl-magn";
+ reg = <0x1e>;
+ irq-gpios = <&gpioa 4 0>;
+ label = "LIS2MDL";
+ status = "ok";
+ };
};
and adding boards/arm/nucleo_f411re/dts.fixup with following
content:
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_LABEL
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_BASE_ADDRESS
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_BUS_NAME
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_IRQ_GPIOS_CONTROLLER
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_IRQ_GPIOS_PIN
For more info on this LIS2MDL please follow this link:
http://www.st.com/en/mems-and-sensors/lis2mdl.html
Signed-off-by: Mario Tesi <mario.tesi@st.com>
The $srctree environment variable gives the path relative to which
'(o)source' statements work (the current directory is used if $srctree
is unset). It is set to $ZEPHYR_BASE in cmake/kconfig.cmake, so there's
no need to qualify the source of Kconfig.zephyr in sample Kconfig files
(or in external projects).
All 'source's in Zephyr assume that the Zephyr root directory is used as
the srctree as well, and would break otherwise.
Remove the $(ZEPHYR_BASE)s to make it clearer that all 'source'
statements work relative to the Zephyr root. There was some user
confusion on IRC.
Also explain how things work in the documentation.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Every board that uses dts-enabled spi drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_SPI_DEVICE and
HAS_DTS_SPI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled i2c drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_I2C_DEVICE and
HAS_DTS_I2C.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
When running a UART test in CI, it is better to configure
the nativeposix UART to be mapped to the process STDIN/OUT.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The Kconfig option CONFIG_BUILD_TIMESTAMP became unused when
BUILD_VERSION was introduced, but it's option and parts of it's
implementation was not completely cleaned from the repository.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Adding i2c slave requires overlay with node definitions and
proper aliases depending on driver implementation.
Modified i2c_slave_api test to use information from dts.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
It is no longer necessary to set the KCONFIG_ROOT variable when the
KConfig file is in the application root directory.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The apds9960 sensor driver recently added support for trigger mode, but
the gpio dts fixups weren't added to the build_all test. Adds the
missing dts fixups and updates the sensor trigger test to include the
apds9960 sensor driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Andrzej Głąbek