This check is needed to not send command that is not supported
by controller. LE Set Privacy Mode command was introduced in
Bluetooth 5.0 so that it will fail on older controllers.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
Add a test to verify that k_sleep() can be used to put
the calling thread to sleep for a specified number of
ticks during system initialization.
This test is inspired from legacy test_early_sleep test
from v1.7.0 release.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
ESP-IDF commit cb31222e added the dependency on a file named
"sdkconfig.h", which is equivalent to "autoconf.h" generated by kbuild
used in Zephyr. It does not depend on anything from that file, though,
so just provide an empty file to keep the compiler from complaining.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
When returning into a different thread than we interrupted, we
obviously need to spill all the existing register windows to make sure
all their values are in the old thread's stack. But the code to do
this forgot to reset the current stack pointer to the value it had at
interrupt time (it was still pointing to the saved context below
that), so the caller of the interrupted function was spilling to the
wrong spot.
This wouldn't show up as an instant failure, it would only happen when
switching BACK to the improperly-spilled thread. And even then it
would be a noop if the original interrupt handler was deep enough to
have spilled that function naturally.
In practice, this happened only in some instances on ESP-32 (which has
more windowed registers than qemu) when interrupting the idle thread
(which is very shallow) with a (very simple) timer interrupt. Trivial
to see, hard to find.
See https://github.com/zephyrproject-rtos/zephyr/issues/6346 for more
detail.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
_sem_give_non_preemptible is non preemptible and no need to move thread
to ready queue for any real use case. Remove old code. This is also
not public API
Signed-off-by: Punit Vara <punit.vara@intel.com>
Not all boards are going to have the ccs811 on them, and thus not in the
device tree. We need a dts.fixup stub to dummy out the CONFIG_CCS811_*
defines that the driver expects.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The arithmetic performed on the CO2 and VOC measurements is pointless as
the units of the sensor already match those of the API, furthermore the
multiplication will overflow the u32_t with CO2 or VOC readings greater
than 4294 ppm or ppb. This CO2 concentration is achievable by breathing
at the sensor.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
The arm qemu platform has limitiations as we get into more complicated
features like userspace support. Add one hardware platform to catch
issues in sanitycheck for development of such features.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A condition is added to the Kconfig file to disable config options which
will be supplied from the dts.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Commit 08de658eb ("kernel: mem_domain: Check for overlapping regions
when considering W^X") introduced some compile issues on various
platforms.
The k_mem_partition_attr_t member is attr not attrs. Also, fix an issue
where sane_partition_domain neesd a pointer to a parition.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We use ctx->user_data to hold socket flags. As each call to
net_context_recv() and net_context_send() overwrites its previous
value, we explicitly must pass the current ctx value there.
Without this, non-blocking socket was turned into blocking after
e.g. switching from receiving to sending.
Fixes: #6309
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
If accept callback is called with error, don't treat the context
passed to the callback as a new accepted context.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
We pass normal 1-based mask, and mask invert it before logically
AND'ing with the value. This apparently a mix-up between how the
mask was intended to be passed initially and how it was in the end.
This issue actually didn't have an effect, because currently defined
flags have mutually exclusive lifetime (when "eof" flag is set,
"non-blocking" flag value is no longer import). Anyway, that's a
bug and needs fixing.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Include and describe all the highlights in the 1.11 release, listed in
the major features initial section and described in the different
subsections in more detail.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
net_app_ctx maintains multiple net contexts(net_ctx). But when http
api's wants to reply or send some data, its always choose the first
net_context in the array, which is not correct always.
net_app_get_net_pkt_with_dst() api will select proper context
based on destination address. So with the help of new api in
net_app, http can select proper context and send packets. To
achieve this, desination address is provided in http_recv_cb_t
and http_connect_cb_t callbacks. Also chaged relevant API's to
provide destination address in http message preparation methods.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Update the home page to add a choice for the 1.11 docs and update the
release notes page to add the 1.11 release notes link.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Add support for building the WS2812 LED strip driver sample against
the new ws2812b_sw driver. Currently a configuration is only provided
for the BBC micro:bit board.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This driver uses a bit-banging based technique of generating a signal
for the WS2812B LED strip. Since bit-banging is very timing sensitive,
where each CPU cycle counts, the driver uses inline assembly to
perform the most critical operataions. This initial version of the
driver only supports a Cortex-M0 implementation, and can e.g. be used
with the ZIP Halo LED strip for the BBC microbit:
https://www.kitronik.co.uk/5625-zip-halo-for-the-bbc-microbit.html
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We're missing a k_sem_give for contexts_lock in the
CONFIG_NET_OFFLOAD path of net_context_put().
This fixes a network hang which occurs after any http_close()
call when CONFIG_NET_OFFLOAD is enabled.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
Reduce the code duplication in ext/hal/st/stm32cube/CMakeLists.txt by
using a foreach loop instead of copy-paste for each SoC.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This fixes intercompatibility issues with controllers supporting
privacy feature.
Core Spec requires to use network privacy mode as a default when
peer device provides its IRK during bonding when LL Privacy is used,
which is the case for Zephyr. We've seen devices including PTS
which exchanges it's IRK but is not aware about network privacy
mode. This results in Zephyr not able do be reconnect to such bonded
devices.
This workaround sets device privacy mode to be able to reconnect
to such devices.
Fixes#4989Fixes#5486
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
The Linux Foundation has been assigned a Company Identifier, and with it
a means of identifying Zephyr over the air. Default to the LF Company
Identifier, which can be overridden by silicon vendors.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Logic for sending chunks of data is incompatible with adding
Content-Length: header.
Per https://tools.ietf.org/html/rfc7230#section-3.3.1:
"A sender MUST NOT send a Content-Length header field in any
message that contains a Transfer-Encoding header field."
Going a bit further in my mind: also don't send Transfer-Encoded
chunked data either when the Content-Length header is present.
In general, there will be problems if the http client library
makes payload changes without the user code knowing about it.
This patch removes the use of http_send_chunk() from the new
HTTP client code and instead sends the payload directly to
http_prepare_and_send()
This fixes an issue where every available buffer would be allocated
with repeating payload data because the for loop in http_request()
wasn't ending until we ran out of memory.
NOTE: This patch was previously applied but was lost when
commit d1675bf3e6 ("net: http: Remove the old legacy API")
moved code around.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
It's added in subsys/net/lib/http/http_client.c:http_request():95
after adding the protocol header. If we add 2 CRLF it ends the
header block and causes an HTTP error.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
In commit 9489fa54cc ("net: http: Fix http_prepare_and_send"),
the logic for when to call http_send_flush() was incorrect. This
is causing a call to http_send_flush() every time
http_prepare_and_send() is called.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
We should not use the user suppied timeout setting in
http_client_send_req() for the connection timeout. In the
previous API the call to tcp_connect() used
CONFIG_HTTP_CLIENT_NETWORK_TIMEOUT as the timeout setting.
Let's do that here too.
This fixes -ETIMEDOUT error generation when using K_NO_WAIT
for http_client_send_req().
NOTE: This patch was previously applied but was lost when
commit d1675bf3e6 ("net: http: Remove the old legacy API")
moved code around.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
In previous version of the HTTP API, commit 8ebaf29927 ("net: http:
dont timeout on HTTP requests w/o body") fixed handling of HTTP
responses without body content.
For the new API, let's add a specific fix for when PUT/POST requests
are responded to with just the status code.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
Initially this sample was intended to be very simple and schematic,
but as this sample going to become a base for stream API conversion,
time to handle all the edge conditions.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Mariusz Skamra