This commit adds CAN support for nucleo F746zg.
Furtermore CAN was added in stm32f7.dtsi and pinmuc_stm32f7.h
CAN_RX: PD0, CAN_TX: PD1
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Add support for pulsing the hardware reset pin of the FXOS8700 high
during initialization.
According to the datasheet, this is required for the I2C/SPI bus
auto-detection logic to work properly if the VDD/VDDIO power
sequencing order cannot be guaranteed.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
gpio_intel_apl_read() should set *value to 1, not 2, when the
GPIO input is a logical high.
Fixes: #15499
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
For STM32L47x/48x series devices, register ASCR should be configured to
connect analog switch of gpio lines to the ADC.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Allows to enable initial RTS/CTS hardware flow control
in the dts.
Co-authored-by: Benoit Leforestier <benoit.leforestier@gmail.com>
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
Reformat L4 pinmux to be consistent with other pinmux files,
and for a better reading.
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
Fixed using chipselect with seperate chipselect GPIOs and how they were
referenced from/in DeviceTree.
Also configure the device during initialization so it's ready to go
after init.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
Adjusted the MCP2515 driver to switch from KConfig SPI configuration to
DTS based configuration.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
The MCP2515 is a CAN controller that can be connected via SPI to an
host MCU. This driver adds support for the MCP2515 as a new driver in
the CAN subsystem.
As it is a SPI peripheral it uses a thread for its interrupt
handling and the received message filtering is done inside this
interrupt thread, as the MCP2515 filter capabilities are not sufficient
for the Zephyr CAN interface.
The driver was validated with an external CAN logger and the adjusted
CAN sample application.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
The following fix:
commit c8b17ec403
Author: Tobias Aschenbrenner <tobias.aschenbrenner@blik.io>
Date: Tue Dec 18 14:16:00 2018 +0100
fix: kw41z: Use correct mapping for dBm
Was using SYS_LOG_INFO and should be using LOG_INFO.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A parallel PCI implementation ("pcie") is added with features for PCIe.
In particular, message-signaled interrupts (MSI) are supported, which
are essential to the use of any non-trivial PCIe device.
The NS16550 UART driver is modified to use pcie.
pcie is a complete replacement for the old PCI support ("pci"). It is
smaller, by an order of magnitude, and cleaner. Both pci and pcie can
(and do) coexist in the same builds, but the intent is to rework any
existing drivers that depend on pci and ultimately remove pci entirely.
This patch is large, but things in mirror are smaller than they appear.
Most of the modified files are configuration-related, and are changed
only slightly to accommodate the modified UART driver.
Deficiencies:
64-bit support is minimal. The code works fine with 64-bit capable
devices, but will not cooperate with MMIO regions (or MSI targets) that
have high bits set. This is not needed on any current boards, and is
unlikely to be needed in the future. Only superficial changes would
be required if we change our minds.
The method specifying PCI endpoints in devicetree is somewhat kludgey.
The "right" way would be to hang PCI devices off a topological tree;
while this would be more aesthetically pleasing, I don't think it's
worth the effort, given our non-standard use of devicetree.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Enable the clock for GPIO ports on the RV32M1 SoC before attempting to
access the port controller registers.
Fixes: #15339
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
According to documentation Compare event will not be triggered
if CC=0 and CLEAR task is set. Added handling of that situation.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The radio API expects the setting of the TX-power in dBm. The actual
TX-power is however set by a 6bit register, which mapping between
register value and power in dBm is a lookup-table in the datasheet.
This mapping for the kw41z was off, which not only lead to incorrect
output power, but also to a maximal output power of only -1.9 dBm
instead of the possible +3.5 dBm.
Signed-off-by: Tobias Aschenbrenner <tobias.aschenbrenner@blik.io>
Signed-off-by: Franco Saworski <f.saworski@posteo.de>
If the user attempts to send data before the USB connection is
established (see the HID sample for an example of such code), the
DataInCallback never gets called which leaves the write semaphore in a
taken state forever.
Signed-off-by: Josef Gajdusek <atx@atx.name>
The SYSCFG_CFGR1_PA11_PA12_RMP define is present even on packages where
the remap isn't strictly required. This commit makes the remap optional
based on a DT property.
Also fixes syntax error caused by a missing );.
Signed-off-by: Josef Gajdusek <atx@atx.name>
Clearing the pending IRQs when resetting the timeout fixes the
forward time drifting, but the change needs more investigation
until we are sure this won't break kernel time management.
Reverting the change to get 1.14 release out.
This reverts commit 2895da02a4.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
HFCLK may be requested for multiple modules, i.e. Bluetooth stack.
When any other module has requested HFCLK to run, the driver will
return -EBUSY on free attempt which is not an error - thie means
that free request has been processed, but someone else is still
requiring the clock to run. When all clock users free the clock,
it may be disabled.
Related issue: #15145
Signed-off-by: Paweł Zadrożniak <pawel.zadrozniak@nordicsemi.no>
As part of the ll_reserve refactoring effort, the packet length now
includes header size as well. Before the refactor, when the packet
length was written to the device, it did not include the header size,
which is the required value as per the LM3S6965 datasheet. After the
refactor the packet length includes the header size as well. The
header size has to subtracted from the packet length before writing to
the device. Fixes#13943.
Signed-off-by: Vijay Kumar B <vijaykumar@zilogic.com>
In the unlucky scenario of a SysTick event (wrap) occurring
while we re-program the last_load value, the SysTick ISR
will run immediately after we unlock interrupts. In that
case the timeout we have just configured will expire
instantaneously, leading to operations being executed
much earlier than expected. Avoid this by clearing possibly
pending SysTick exceptions (writing 1 to ICSR.PENDSTCLR).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
When the counter reaches zero, it reloads the value in
SYST_RVR on the next clock edge. This means that if the
LOAD value is N, the interrupt ("tick") is triggered
every N+1 cycles. Therefore, when we operate in tickless
mode, and we want to schedule the next timeout, we need
to configure the LOAD value with last_load - 1, in order
to get an event in last_load cycles.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
When the counter reaches zero, it reloads the value in
SYST_RVR on the next clock edge. This means that if the
LOAD value is N, the interrupt ("tick") is triggered
every N+1 cycles. Therefore, when we operate in non-
tickless mode, we need to configure the LOAD value
with CYC_PER_TICK - 1, in order to get an event
every CYC_PER_TICK cycles.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Check maximum packet size (MPS) of an endpoint in usb_dc_kinetis
and usb_dc_native_posix drivers.
resolves#14957resolves#14954
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
The SysTick logic looked logically sound, but it was allowing us to
set a LOAD value as low as 512 cycles. On other platforms, that
minimum future interrupt delay is there to protect the "read, compute,
write, unmask" cycle that sets the new interrupt from trying to set
one sooner than it can handle.
But with SysTick, that value then becomes the value of the LOAD
register, which is effectively the frequency with which timer
interrupts arrive. This has two side effects:
1. It opens up the possibility that future code that masks interrupts
longer than 512 cycles will miss more than one overflow, slipping
the clock backward as viewed by z_clock_announce().
2. The original code only understood one overflow cycle, so in the
event we do set one of these very near timeouts and then mask
interrupts, we'll only add at most one overflow to the "elapsed()"
time, slipping the CURRENT time backward (actually turning it into
a non-monotonic sawtooth which would slip every LOAD cycle) and
thus messing up future scheduled interrupts, slipping those forward
relative to what the ISR was counting.
This patch simplifies the logic for reading SysTick VAL/CTRL (the loop
wasn't needed), handles the case where we see more than one overflow,
and increases the MIN_DELAY cycles from 512 to 1/16th of a tick.
Fixes#15216
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Bad order of interrupt calls made it unable to transmitt data
using interrupt driven API.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This is a leftover license header from when we used a third party
driver that had since been replaced.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Fix build error when executing sanitycheck on stm32 devices.
Command to execute tests:
sanitycheck --device-testing --device-serial /dev/ttyACM0 -p <board>
-t usb
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This macro is slated for complete removal, as it's not possible
on arches with an MPU stack guard to know the true buffer bounds
without also knowing the runtime state of its associated thread.
As removing this completely would be invasive to where we are
in the 1.14 release, demote to a private kernel Z_ API instead.
The current way that the macro is being used internally will
not cause any undue harm, we just don't want any external code
depending on it.
The final work to remove this (and overhaul stack specification in
general) will take place in 1.15 in the context of #14269Fixes: #14766
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
unify the API of CCM alogrithm's implemation for TinyCrypt,
mbedTLS and cc2520 crypto device to make users easy to use.
Fixes#8339.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Alexander Wachter