In some hardware, e.g. ARC HS Development kit,the peripheral
space of DesignWare SPI only allowes WORD access,
byte acess will raise bus error.
This commit adds support for this case
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
It involves a minor change on which register is configured.
Most of the change is with threshold handling.
Handling the Kconfig based supported mode per-port.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As for RX only, computing the NDF will be used for EEPROM mode.
Only a way to determine EEPROM mode is missing.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Introducing as well a generic driver helper for CS gpio control and
buffer management.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Make pointers to struct config_info const in prepration for a const
config_info.
Change-Id: I28789a7f1f26e4a0d499f5a89a567ae8c61eae51
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@gmail.com>
Just as rxftlr can be read, a macro is needed so that txftlr can be read.
Symmetry.
Change-Id: Id987f700d89268feca60850f4fdf512f990f3ab6
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Though it's an ARC core, Quark SE SS does not follow the same registers
mapping as the official DesignWare document. Some parts are common, some
not.
Instead of bloating spi_dw.c with a lot of #ifdef or rewriting a whole
new driver though the logic is 99% the same, it's then better to:
- centralize common macros and definitions into spi_dw.h
- have a specific spi_dw_quark_se_ss_reg.h for register map, clock
gating and register helpers dedicated to Quark SE SS.
- have a spi_dw_regs.h for the common case, i.e. not Quark SE SS.
GPIO CS emulation and interrupt masking ends up then in spi_dw.h.
Clock gating is specific thus found in respective *_regs.h header.
Adding proper interrupt masks to quark_se_ss soc.h file as well.
One of the main difference is also the interrupt management: through one
line or multiple lines (one for each interrupt: rx, tx and error). On
Quark SE Sensor Sub-System it has been set to use multiple lines, thus
introducing relevant Kconfig options and managing those when configuring
the IRQs.
Quark SE SS SPI controller is also working on a lower level, i.e. it
requires a tiny bit more logic from the driver. Main example is the data
register which needs to be told what is happening from the driver.
Taking the opportunity to fix minor logic issues:
- ICR register should be cleared by reading, only on error in the ISR
handler, but it does not harm doing it anyway and because Quark SE SS
requires to clear up interrupt as soon as they have been handled,
introducing a clear_interrupts() function called at the and of the ISR
handler.
- TXFTLR should be set after each spi_transceive() since last pull_data
might set it to 0.
- Enable the clock (i.e. open the clock gate) at initialization.
- No need to mask interrupts at spi_configure() since these are already
masked at initialization and at the end of a transaction.
- Let's use BIT() macro when relevant.
Change-Id: I24344aaf8bff3390383a84436f516951c1a2d2a4
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Watson Zeng