Add the codec reset GPIO to intel_s1000_crb's DTS
Update the DTS fixup for intel_s1000_crb accordingly
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Add board support files for mimxrt1020_evk, the development board for
i.MXRT1021 (CM7) SoC.
- Add pinmux, dts, doc.
- Code can be loaded to SRAM.
- Tested samples: hello_world, philosophers, synchronization,
basic/blinky, and basic/button.
Signed-off-by: Ryan QIAN <jianghao.qian@nxp.com>
Convert the w25qxxdv driver to use device tree for SPI device params.
Updated the Arduino 101 config to use device tree to specify the SPI
flash. Update the arduino_101_sss to drop Kconfig support for the
w25qxxdv flash.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
By default, after reset SWO signal is not connected to GPIO pin.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
By default, after reset SWO signal is not connected to GPIO pin. This
commit adds required initialization code to enable support for SWO
logger. Not all SoC series support the feature.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
lpuart1 is the default port used by ST-Link VPC.
Update board description to match out of box board configuration.
Fixes#12092
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following recent renaming of STM32 UART Kconfig UART symbols,
LPUART was named as UART_LPUART_1.
Rename to LPUART_1.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
* Add DTS support for gpio controller driver
Signed-off-by: Ashokkumar B <ashokkumar@zilogic.com>
Signed-off-by: Subash G <subash@zilogic.com>
Signed-off-by: Vishnu K <vishnu@zilogic.com>
Signed-off-by: Vaishnavi D <vaishnavi.d@zilogic.com>
By adding 'aliases' node in SoC .dtsi file it is possible to generate
DT_ defines which specify a logical name rather than relay on module
location on APB bus. E.g. DT_SILABS_GECKO_USART_40010000_LABEL becomes
DT_SILABS_GECKO_USART_USART_0_LABEL. Thus it is possible to remove
dts_fixup.h defines.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
In 4940a3cac2 a compile time
check of the HW model version was added. This check worked
fine for cases in which the problem was that people had not
fetched a new enough version of the HW models.
But in some cases people will have fetched a new enough version
but be (unknowingly) in a past detached HEAD (or old tag).
With this change we ensure that the required tag is an actual
ancestor for the current HW models version HEAD
Also fail with an error, instead of just printing a warning.
Users can still disable this warning if they know what they are
doing.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The i2c_atmel_sam3 driver was deprecated at release 1.9, this commit
removes it. Also pinmux_dev_atmel_sam3x driver is removed.
i2c_atmel_sam3 was the last one which depended on it.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Remove configuration parameter CONFIG_BUS_TYPE. Now we may
make use of DT_ST_LSM6DSL_BUS_I2C and DT_ST_LSM6DSL_BUS_SPI
definition to select the bus.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
With this change, drivers or components can register on runtime
their own command line arguments.
What this change does is to use the dynamic command line arguments
API from BabbleSim's libUtil and provides a function for the
drivers to add their own.
Note that this change requires v1.3 of the HW models (which remove
a dependency on the board command line arguments structure)
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
This function can only be used when the arguments structure memory
layout starts as in bs_basic_dev_args_t.
This assumption is just too dangerous in this board as somebody
may change the structure in the future unaware of this weird
requirement.
=> Do not use this function but do what it does in place.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
When the -nosim option is used the user may still want to set
either the simulation ID string (-s) or the device number (-d)
to control the tracing prefixes and/or dump folder, but may not
care to set both of them.
=> This change allows it, while the old behaviour is otherwise
maintained (setting both or none with -nosim)
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Updated flash partitions to extend supported boot scenarios.
Add support for using Nordic nRF5 bootloader to:
- flash a Zephyr application
- flash a MCUboot image as an application
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
The en.high-perf_nucleo-144_mbed.jpg is an empty file.
This causes error when generating PDF documentation
as the tool cannot deal with empty image files.
So replace it with the image with same filename from
nucleo_f765zg, as the images are identical from
the online product description pages.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
interface/stlink-v2-1.cfg and interface/stlink-v2.cfg are wrappers
around interface/stlink.cfg, their inclusion trigger warning which
this change addresses. Besides the warning there is nothing there
except sourcing iterface/stlink.cfg directly.
Signed-off-by: Vasili Slapik <vslapik@gmail.com>
This mode allows the USB driver to use MSI clock as source clock.
MSI PLL-Mode permits +/-0,25% accuracy.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
The L476RG does not use the same I2C instance as the other L4 boards.
Correct the pinmux and add the peripheral.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
patch set the config USB_DFU_MAX_XFER_SIZE to 4096. This will
reduce the time required for flashing.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Document CAN support for board nucleo_l432kc and
add can to board yaml "support" section.
Fixes#12052
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Fix misspellings in documentation (.rst, Kconfig help text, and .h
doxygen API comments), missed during regular reviews.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Enable by default the following hardware instances in Kconfig:
- ADC_0
- I2C_0
- SPI_1 (SPI_0 for nRF52810)
for all nRF development kit boards having the corresponding DT nodes
enabled. This way there is no need to enable these instances in
particular applications, like samples for sensors or tests for drivers.
I2C_0 and SPI_0 cannot be used simultaneously in most of nRF SoCs,
nRF52810 is the only exception so far (and in this SoC SPI_1 is not
present, hence SPI_0 is enabled for it).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The options selecting nRF drivers are now enabled by default when
an nRF SoC is selected as the build target.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Fixes board PHY initialization.
ENET_RST and ENET_INT pins are also used as USER_LED/JTAG_TDI and
INT1_COMBO/JTAG_TDO. Initialization needs to set these pins to power and
interrupt for the PHY Transciver. PHY reset works without busy waiting.
Moved pin initialization back to PRE_KERNEL_1 to fix UART bug and busy
wait not required.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Added support for SPI 1 available from the arduino connector (plus an
extra gpio). Tested against samples/sensor/bme280.
Added warnings in documentation, pinmux and dts highlighting a potential
conflict if using SPI_1 and on-board ethernet at the same time.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
Added board definitions for nucleo_f756zg. Features include gpio,
pinmux, uart (ST Zio, ST-Link and Arduino Uno v3 interfaces).
Added basic documentation and some soc definitions for the
stm32 f756XX soc.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
Updated .dts and pinmux.c to highlight pin conflict on PA7 if ETH and
SPI_1 are selected together without modification.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
STM32 uart Kconfig instance flags were not following
same naming scheme than other drivers (i2c, spi, ..)
Update driver to use UART_X instead of UART_STM32_PORT_X
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch cleans up the code in the recently added dts_fixup.h,
restoring the original alignment of the file.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The dts.fixup for mps2_an385 contains a wrong setting for the IRQ fixup
for the Dual Timer IRQ.
This patch fixes the symbol included in the generated header.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Sathish Kuttan