Added alias (mcuboot-led0) for the LED gpio pin which might be
used by MCUboot.
So far this pin assignments for MCUboot was configured by
bootloader-led0 alias.
New alias will replace the bootloader-led0.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Added alias for the button's gpio pin which might be used by MCUboot.
So far pin assignments for MCUboot was configured by the Kconfig. New
alias will help to switch configuration to more native DTS based
description.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
... and "nordic,nrf-pwm" binding:
- use channel indexes instead of pin numbers in `pwms` properties that
define PWM LEDs
- add the period and flags cells to `pwms` properties in all PWM LED
definitions; use the commonly used period of 20 ms (giving 50 Hz)
as a default setting
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Prevent "unique_unit_address_if_enabled" warnings from being reported
for nRF52 Series SoCs, where certain nodes need to be enabled with
the same base addresses. These can be (depending on a given SoC):
- power@40000000 & clock@40000000
- power@40000000 & clock@40000000 & bprot@40000000
- acl@4001e000 & flash-controller@4001e000
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
A follow-up to #44181, this time fixing the pyocd target parameters to
match the actual hardware on the board.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The jlink executable expects a fully qualified IC name, and not just the
family. Apply to all Nordic boards.
Fixes#37294
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This sentence ("Other hardware features are not supported by the
Zephyr kernel."), which could be found in a high number of boards
documentation, is misleading on two levels:
- peripheral support is not a kernel business
- in most of cases, features are actually supported but not enabled.
Fix this.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
These changes turn out to have been incompatible with the way pinctrl
drivers are going to work, so we need to go back to what we had before
until we can agree on a better approach.
Squash of the following reverts:
Revert "boards: nrf: fix deprecated I2C properties"
This reverts commit 2a4ac9ac02.
Revert "samples: switch nrf overlays to sda-gpios, scl-gpios"
This reverts commit 01bb08e7d8.
Revert "boards: nrf: switch to sda-gpios, scl-gpios"
This reverts commit 17a66304c4.
Revert "i2c: nordic: switch to phandle arrays for pinmux"
This reverts commit 821c03a14a.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
MCUboot recently gives possibility to signal its state
using led.
For leverage this feature need to provide proper alias
for the led gpio pin.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Move the BOARD.dts files for Nordic-based boards to use the new I2C
devicetree properties for specifying the SDA and SCL pins.
This was done with a script.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Rework the runner to improve various issues.
Every board.cmake file for an nRF SoC target is repeating boilerplate
needed for the nrfjprog runner's --nrf-family argument. The
information we need to decide the --nrf-family is already available in
Kconfig, so just get it from there instead. Keep the --nrf-family
argument around for compatibility, though.
This cuts boilerplate burden for board maintainers.
We also need to revisit how this runner handles recovery to fix it
in nRF53 and keep things consistent everywhere else.
To cleanly handle additional readback protection features in nRF53,
add a --recover option that does an 'nrfjprog --recover' before
flashing. Keep the behavior consistent across SoCs by supporting it on
those too. Because this is expected to be a bit tricky for users to
understand, check if a --recover is needed if the 'nrfjprog --program'
fails because of protection, and tell the user how to fix it.
Finally, instead of performing a separate 'nrfjprog --eraseall', just
give --chiperase to 'nrfjprog --program' process's arguments instead
of --sectorerase. This is cleaner, resulting in fewer subprocesses and
avoiding an extra chip reset.
Having a separate 'west flash --recover' option doubles the number of
test cases if we want to keep exhaustively enumerating them. That
doesn't feel worthwhile, so update the test cases by picking a
representative subset of the possibilities. Each test now has enough
state that it's worth wrapping it up in a named tuple for readability.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Nordic Dev Kit board names were changed in Zephyr
v2.3 release, following the standard Board deprecation
policy. Two releases later we do not need to keep
references to the old names in the boards' documentation.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
In the flash partition definitions for ARM boards,
the link to the legacy partition macros does not
exist any more. The commit cleans up the partition
definition by removing this link.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
In all Nordic boards that contain ICs that support hardware stack
protection, turn it on by default so that we detect
stack overflows easier.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The Kconfig PWM_[0-3] sybmols don't have any meaning for nrf family of
SoCs. The driver doesn't utilize them and no sample or test code does
either so we can remove setting them in board Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The SoC node has compatibles for the specific SoC in place, having the
same compatible at the top level is technically a conflict and the
top-level one should really just be about the board. Remove the SoC
related compatibles at the top-level.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use the new devicetree API. Remove per-board enabling of ADC_0 by
setting ADC_0 to default y when the 'adc' node label points at an
enabled node of the expected compatible (depending on SoC).
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The board name for the nRF52 DK, so far known as nrf52_pca10040, is
renamed to nrf52dk_nrf52832. Its documentation and all references
to its name in the tree are updated accordingly. Overlay and
configuration files specific to this board are also renamed, to
match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Andrzej Puzdrowski