The nRF54L05 and nRF54L10 are identical to the nRF54L15 except for their
memory sizes. Add support for emulating those ICs on the nRF54L15DK.
This commit only adds support for the main application core. Support for
the FLPR core may be added later.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the rather logical convention for the name that is applied to other
Nordic boards: <board>_common.dtsi for definitions that are common to
the board itself (LEDs, buttons, etc).
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The nRF54H20 Development Kit version 0.8.0 is no longer supported, given
that they should have all been replaced by 0.9.x.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Status and request GPIOs are missing from the edge connector, add those
to fix Thingy53 + nRF7002EB build.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Remove CONFIG_SDMMC_VOLUME_NAME, and set the disk name based on the
``disk-name`` property. This aligns with other disk drivers, and allows
for multiple instances of the sdmmc_subsys disk driver to be registered.
Add disk-name properties for all in tree definitions for the
sdmmc-subsys disk driver, and change all in tree usage of the disk name
Fixes#75004
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
In preparation of adding a check for dead references, this commit fixes
currently broken zehpyr_file: links.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Extended UICR will not be used as its configurations will be merged
with the UICR registers in NVR.
Memory maps changes are needed to align with pre compiled
firmware.
Signed-off-by: Håkon Amundsen <haakon.amundsen@nordicsemi.no>
Signed-off-by: Jonathan Nilsen <jonathan.nilsen@nordicsemi.no>
The nRF54 and nRF92 chips has data cache, which means
the ICMsg and ICBMsg must be configured to follow required
cache alignment of the shared memory.
The `dcache-alignement` needs to be defined for that.
Signed-off-by: Dominik Kilian <Dominik.Kilian@nordicsemi.no>
A bunch of copy-paste mistakes when adding the nRF54L15 DK added stale
references to the Preview DK (PDK).
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Doc and .yaml descriptions shall mention retained_mem
in supported features on affected boards.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Update the default memory maps for `nrf54h20dk` and `nrf9280pdk` to
remove the `shared_ram20_region` and `shared_ram3x_region` nodes,
because their child nodes no longer need to be grouped together:
* IPC buffers in RAM20 are statically allocated.
* DMA buffers in RAM3x have separate access owners.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Apply the following changes to `nrf54h20dk` and `nrf9280pdk`:
* Convert `perm-*` properties to the newly introduced `nordic,access`,
both in board files and tests.
* Redefine shared regions to specify multiple access owners per node,
and ensure that each such region is reserved by one domain at a time.
`cpuapp_cpurad_ram0x_region` is only enabled by Radiocore, while
`cpuapp_cpucell_ram0x_region` is only enabled by Application core.
* Divide `shared_ram3x_region` so that each sub-region is owned by a
different domain. Their addresses must be rounded down to fit the
current UICR format.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
The external flash (mx25r64) was accidentally disabled during
testing. The node should be enabled by default like its spi.
This commit removes the status = "disabled";
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Like in all other legacy boards, hw-flow-control should not be
enabled for console UART. With hw-flow-control sample stuck
during printing some initial information and sample appears to
be not working correctly unless com port is opened.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
The NS variants need crypto changes from NCS, so, remove it from
upstream till their support is upstreamed.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Full name was set based on the information available either in board
documentation or in Twister files.
Whenever applicable, vendor name was dropped from the full name so that
all boards have a consistent naming scheme.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Some tests are failing on nrf54h20 cpurad in non-obvious manner
because of this memory region being too small.
Instead of adding overlays to each individual application,
make this region larger at expense of cpuapp equivalent.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Version 2 of the ADAC interface implemented by secure domain firmware
changes the ADAC RESET command used in the custom reset handling in
the JLink support scripts. The command has been split into two
commands, RESET and START, and has different semantics from
the previous RESET command. The new RESET command resets both the
application and radio domains without starting the CPUs again, and the
START command must then be used to start the CPUs.
Update the JLink support scripts for nrf54h20dk/nrf54h20/cpuapp,
nrf54h20dk/nrf54h20/cpurad, nrf9280pdk/nrf9280/cpuapp and
nrf9280pdk/nrf9280/cpurad so that they read out the ADAC interface
version from the device and use the newer commands if ADAC version 2 is
detected. If the version is lower than 2, the legacy implementation is
used.
Also improve the CTRL-AP MAILBOX transaction implementation
to avoid the need for arbitrary sleeps or unnecessary polling of
the MAILBOX. This should improve stability when using the script.
Signed-off-by: Jonathan Nilsen <jonathan.nilsen@nordicsemi.no>
dcache-alignement needs to be defined for ipc to have
consistent memory organization on both endpoints, when
shared memory is cacheable. nrf54h20 and nrf9280 are
using cacheable shared memory.
This is applied for ipc with icmsg backend.
Signed-off-by: Lukasz Stepnicki <lukasz.stepnicki@nordicsemi.no>
Add a new revision for nRF54H20 DK: 0.9.0. This new hardware spin contains
the final nRF54H20 SoC. Treat it as the default, including twister.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The current DK is labeled as revision 0.8.0. Until now, no revisions were
needed, but a new hardware spin is coming, so we'll need to keep at least
two revisions in the near future until the final one becomes the default.
Prepare the board for that scenario. Note that the "old" nRF54H20 SoC is
now nRF54H20 EngB.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This region is only required if certain fast peripherals make use of such
region for DMAing. It was now enabled on all builds, often resulting in:
```
[134/134] Linking C executable zephyr/zephyr.elf
Memory region Used Size Region Size %age Used
FLASH: 24372 B 248 KB 9.60%
RAM: 4448 B 256 KB 1.70%
DMA_RAM21: 0 GB 16 KB 0.00% <~~ Not used!
DMA_RAM3x_APP: 40 B 4 KB 0.98%
IDT_LIST: 0 GB 32 KB 0.00%
```
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add the necessary entries but keep the usbhs disabled by default on
radio core (it is enabled by default on app core).
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
- Only one board tweaked the HFXO configuration (bl5340_dvk)
- LFXO configuration has been added to all boards based on the current
Kconfig defaults: use LFXO with internal 7pF capacitor.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This prevents an overlap with `storage_partition`
Additionally, it fixes the following warning:
> unit address and first address in 'reg' (0x20000) don't match for
> /soc/flash-controller@4001e000/flash@0/partitions/partition@19000
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This board is not currently available for the general public, and the
documentation page adds no value whatsoever. Remove it until the board
is finally available and its features and support can be documented
properly.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Adds missing code-sample directive to the Hello World sample in
preparation for upcoming changes to the Zephyr documentation that will
be leveraging the provided description and metadata.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Add common default flash partition layout for nrf52840 as many boards
have used identical flash layouts.
The default flash layout was updated to remove scrach in 2022 (9a84258)
but almost all boards were still using the previous layout, so this
updates them to the new layout with allows for larger applications.
This commit also incorporates feeedback from @nordicjm in PR #77791 to
change slot0 to 0x00077000 and slot1 to 0x00075000: "If you use swap
using move, you need a sector for the data to be moved up by, and you
need space for the swap status fields, which is about a sector, so by
making the changes here you get the full 0x65000 for an image, without
these changes you get 0x64000.
Signed-off-by: Jacob Winther <jacob@9.nz>
Align settings and DFU partition definition with the values, specified
by the design documentation.
Signed-off-by: Tomasz Chyrowicz <tomasz.chyrowicz@nordicsemi.no>
These parameters will be used by the clock controller drivers.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Remove parts of the documentation for the nrf9280pdk board
that were copy-pasted and added by mistake.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Describe the samples using code-sample directive in preparation for
upcoming changes to the Zephyr documentation that will be leveraging
the provided description and metadata.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Add default memory partitioning for the nRF53 and nRF91 series devices.
As these partitions refer to TF-M and the TF-M layouts cannot be
modified, use the partitioning scheme from TF-M.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Add a composite fuel-gauge device to the Thingy53 to enable converting
the raw voltage to a battery percentage.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Add board support for Application, Radio and PPR cores
of the nRF9230 SoC / nRF9280 SiP on the nRF9280 PDK board.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Co-authored-by: Andreas Moltumyr <andreas.moltumyr@nordicsemi.no>
Carles Cufi