This driver was still using CONFIG_* values to determine its address,
IRQ, etc. Add a binding for an "intel,hpet" device and migrate this
driver to devicetree.
Fixes: #18657
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
XIP support in x86 was something of a mess. This
patch does the following:
- Generic ia32 SOC no longer defines a "flash" region
as generic X86 devices don't have a microcontroller-
like concept of flash. The same has been done for apollo_lake.
- Generic ia32 and apollo_lake SOCs starts memory at 1MB.
- Generic ia32 SOC may optionally have CONFIG_XIP enabled.
The board definition must provide a flash region definition
that gets exposed as DT_PHYS_LOAD_ADDR.
- Fixed definitions for RAM/ROM source addresses in ia32's
linker.ld when XIP is turned off.
- Support for enabling XIP on apollo_lake SOC removed, there's
no use-case.
- acrn and gpmrb boards have flash and XIP related definitions
removed.
- qemu_x86 has a fake flash region added, immediately after system
RAM, for use when XIP is enabled. This used to be in the ia32 SOC.
However, the default for qemu_x86 is to now have XIP disabled.
- Fixed tests/kernel/xip to run by default on boards that enable
XIP by default, plus an additional test to exercise XIP on
qemu_x86 (which supports it but has XIP switched off by default)
The overall effect of this patch is to:
- Remove XIP configuration for SOC/boards where it does not make
any sense to have it
- Support testing XIP on qemu_x86 via tests/kernel/xip, but leave
it off by default for other tests, to ensure it doesn't bit-rot
and that the system works in both scenarios.
- XIP remains an available feature for boards that need it.
Fixes: #18956
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
After witnessing some strange errors with memory not being
what it should be, lifiting everything above 1MB has solved
it. The Zephyr binary was being loaded into memory containing
reserved regions, resulting in data corruption.
We still simulate XIP for testing purposes by setting up the
memory map as follows:
0x000000 - 0x0FFFFF : Non-present
0x100000 - 0x4FFFFF : "Flash" ROM region
0x500000 - 0x8FFFFF : "SRAM" RAM region
For a total of 9 megabytes of physical RAM used.
Fixes problems observed in some large tests when code coverage
is enabled (which increases the amount of RAM used even more).
Fixes: #17782
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Qemu_x86 didn't reflect emulated program memory size.
It was because chosen zephyr,flash was assigned to flash_simulator
which was helping to generate DT_FLASH properties for sim_flash node.
This change revert choice of flash0 which solve problem with
program memory size. Flash simulator have to use
DT_SOC_NV_FLASH_xxx labels for fetch its property since that.
fixes#15832
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
The desired memory map is to have the 0 - 4K page non-present
to catch NULL pointer dereferences,
from 4K - 4MB for the program text (RO, Execute),
ROM (RO, No Execute), and 4MB-8MB for system RAM.
This patch cut text size by 4 KB which allow to meet above
requirements.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Increase ram size as flash simulator need it for
emulated storage. The qemu_x86 flash size is puted back to
its original value of 4092K
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
The '#if XIP' in the DTS file never worked properly,
causing the QEMU build to think it has much more RAM
then it actually has. If RAM overflowed, this would not
be caught by the build, instead there would be strange
crashes when the data copy takes place.
The QEMU targets themselves are not XIP, everything
is actually RAM, but the first 4 megabytes are
considered to be a memory-mapped flash region. This
is done to ensure that the XIP data copying infrastructure
doesn't bit-rot on x86. We are at the point where
a lot of things depend on this, so just select it in
the board Kconfig instead of enabling in the
defconfigs.
Fixes: #15835
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Reduced flash size for QEMU x86 so it does not consume a lot of RAM
memory where it is simulated.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
This commit adds a flash driver implementation that writes to RAM and
exports statistics through stats.h. It can be used to simulate flash
memory for testing purposes.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Now that we have a common DT_SIZE_K macro use it instead of defining
__SIZE_K eveywhere. We also have DT_SIZE_M, so use that in a few
places as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Underscore ('_') isn't a valid char for alias names based on the device
tree spec. Newer dtc compilers flag this as a warning so lets clean it
up. Replaced '_' with '-' to keep things simple.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
patch removes the mem.h and marcos used in that file are
moved appropriate board files. As there are boards with
different flash configuration but of same soc, flash and
ram size are moved to dts file instead of dtsi
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Move the dts files into the board dir so that board ports can be more
standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Charles E. Youse