stm32mp1 was adding a STM32 specific Core selection Kconfig
symbol while zephyr generic CPU_CORTEX_M4 could be used for the
same purpose.
Remove STM32 specific symbol and use generic one.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Sample was not compiling for nordic boards because RTC_0
instance was not enabled by default and RTC_0 device is using
different DT define.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This commit adds counter driver based on RTCC module for SiLabs Gecko
SoCs.
Tested with SLWSTK6061A / BRD4250B wireless starter kit.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
These events aren't errors at all, but rather part of normal operation.
They shouldn't trigger error messages, especially given that the console
gets absolutely flooded with them if power management is activated.
Signed-off-by: Benjamin Lindqvist <benjamin.lindqvist@endian.se>
stm32wb55rg is a dual core SoC (M4/M0) with a radio/protocol stack
running on M0 core. M0 FW starts at flash address 0x80CB000.
So flash size available to zephyr is 812K instead of 1M.
Configure package size to reflect this (flash size is now 812K)
and update MPU setting to exclude M0 FW. From MPU point of view,
we set flash size to 512K since we should chose a size being a power
of 2.
If we consider there will be 2 images partitions in a FOTA scheme,
512 K is beyond image-0 and hence is sufficient to cover application
image.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32WB HCI driver requires definition of 2 RAM regions to support
use of 3 shared memory sections: MAPPING_TABLE, MB_MEM1 and MB_MEM2.
In linker.ld, under conditions of HCI driver to be enabled,
define SRAM1 and SRAM2 based on input defined in stm32wb linker.
Then define the 3 sections MAPPING_TABLE, MB_MEM1 and MB_MEM
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Several customer configuration (CCFG) settings are useful for
development and deployment. This commit adds support for setting CCFG
values via Kconfig. It follows TI's recommendation of setting CCFG
values and then including the TI provided CCFG. This commit includes
support for enabling the ROM bootloader and additional settings can be
added as needed.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
soc_register.h is available in most of stm32 series.
It is sometime empty or contains includes to flash_registers.h,
which is included directly with direct reference in flash driver.
soc_register.h is also included in stm32 clock drivers, but this
driver do not use direct reference to any register anymore.
Clean up these files.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
tests/drivers/i2c/i2c_api wants to have CONFIG_I2C_0_NAME defined.
Add it to dts_fixup.h as was done for Watchdog and & timer.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
This adds support for the basic timer counter (TC) found on SAM0
series parts. This driver only supports running the counter
in 32 bit wide mode. Since this mode explicitly slaves the odd
counters to the even ones, only instances of the even ones are
defined.
Tested with tests/drivers/counter/counter_basic_api on SAMD21.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Define pinmux base addresses from gpio bases. Pinmux
and gpio functionality are located in the same PCR register
for each pin.
Introduce pinmux Kconfig switches for the SOC.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
This commit enforces platform-specific initialization
for nRF SoC family. The specific platform initialization
hook is invoked directly after reset and calls the nRFx
SystemInit() function.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add support for the Low Power Inter-Integrated Circuit (LPI2C)
controllers found in the NXP Kinetis KE1xF SoC series.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add option for enabling the Code Cache present on the NXP Kinetis
KE1xF SoC series and enable it by default.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Unlike Cortex-M3 and Cortex-M4, in Cortex-M7 the number of
MPU regions may vary based on the implementation. This commit
adds a DTS node for the ARM MPU peripheral in the device tree
of Cortex-M7 SoCs and updates the fixup files, so we may extract
the number of MPU regions at build time. SoCs:
- nxp_rt
- same70
- stm32f7
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds a DTS node for the ARM MPU peripheral in the
device tree of ARMv8-M SoCs (for the secure and the non-secure
DTS descriptions) and updates the fixup files. SoCs:
- nrf9160
- musca_a
- musca_b1
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
In kernel_arch_init() we initialize the ARM core (interrupt
setup, fault init, etc.) so we can also move z_clearfaults()
in the same function and skip invoking it in the SoC init
functions.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Sample walk through:
1. CPU 0 will wake up CPU 1 after initialization
2. CPU 1 will send to CPU 0 an interrupt over MHU0
3. CPU 0 return the same to CPU 1 when received MHU0 interrupt
4. Test done when CPU 1 received MHU0 interrupt
The wake up second core and private core ID are soc specific.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
The CONFIG_CLOCK_CONTROL and CONFIG_NRF_RTC_TIMER were
unconditionally selected when enabling any nRF SoC. But since
timers can be disabled in the kernel, depend instead on
CONFIG_SYS_CLOCK_EXISTS, which is only defined when kernel
timer support is included.
Note that ideally we would enable CONFIG_NRF_RTC_TIMER only, and
that would select CONFIG_CLOCK_CONTROL (on which the RTC timer
depends) but there is a circular Kconfig dependency that prevents
us from doing so.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add support for NXP MCUX LPUART devices with separate IRQ lines for
transmit and receive status interrupts (e.g. the Kinetis KE1xF SoC
series).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This commit adds basic support for nrf52811 in the arch SoC, dts
and nrfx folders.
The nRF52811 is a Bluetooth 5.1 Direction Finding SoC with comprehensive
protocol support.
The nRF52811 SoC is capable of the latest features of Bluetooth 5.1,
the most prominent being Direction Finding.
The radio in the nRF52811 SoC has comprehensive protocol capabilities,
including Bluetooth 5.1 Directing Finding, all Bluetooth 5 features,
802.15.4, Thread, Zigbee, ANT and 2.4 GHz proprietary.
It has 4 dBm TX power and has been optimized to offer the best RX
sensitivity of all SoCs in the nRF52 series.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
add usbd1 definition to rt dts file,
set EHCI controller config default value in rt1050 default config file,
add EHCI controller driver MACROs to dts_fixup.h,
initialize EHCI clock in rt soc.c
add HAS_MCUX_USB_EHCI for supported soc in Kconfig.soc
Signed-off-by: Mark Wang <yichang.wang@nxp.com>
Hex firmware file is convenient in some scenarios, like
generating signed firmware with `west sign`. So, enable
generating hex file.
Signed-off-by: Jun Li <jun.r.li@intel.com>
Macros and enums are included for supporting pin configuration
settings.
Entries to the dts_fixup were also included in order
to configure port level settings.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Erwan Gouriou