The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
This patch is equivalent to 7b0ce85242,
but applied to buttons. As stated in the previous commit message:
This change aims at fixing 'unit_address_vs_reg' warning in arm based
boards. This warning pops up when a node name is made up with an
address (node_name@xx) but does not contain a reg property. This case
was encountered for led nodes for instance, where a reg property has
no meaning. Fix this by changing node_name@xx to node_name_xx which
removes the guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F4 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This change aims at fixing 'unit_address_vs_reg' warning in
STM32 based boards.
This warning pops up when a node name is made up with an address
(node_name@xx) but does not contain a reg property.
This case was encountered for led nodes for instance,
where a reg property has no meaning.
Fix this by changing node_name@xx to node_name_xx which removes the
guilty '@xx' syntax but preserves node_name uniqueness.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following changes are necessary to use LP3943 LED driver present
in 96Boards Neonkey board
1. Enable I2C_3 interface
2. Reduce the speed of I2C_3 bus on 96Boards Neonkey. Due to some
design quirks, on board LP3943 LED driver connected to I2C_3
operates only at Standard speed of 100KHz.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
To prepare to upcoming dtc v1.4.6, fix warnings in dts files.
This commit addresses the following warning:
"unnecessary #address-cells/#size-cells without "ranges" or child
"reg" property in /gpio_keys".
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Configure SPI using DT for the following STM32 boards:
96b_neonkey
nucleo_f091rc
nucleo_f334r8
nucleo_f401re
nucleo_l432kc
nucleo_l476rg
SPI nodes in <board>.dts file are populated matching boards existing
pinmux default configuration and enabled in Kconfig.defconfig if
SPI is enabled.
For nucleo_l476rg board SPI2 and SPI3 nodes are not yet added, because
of missing pinmux defines.
Fixes#5836
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
Move the dts files into the board dir so that board ports can be more
standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Ulf Magnusson