- enabled combined interrupt configuration for stm32u0x serie.
- since stm32u0 serie doesn't support SMBUS we need to avoid
use SMBHEN and SMBDEN bits register.
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
Select PINCTRL subsystem by drivers which require it.
Prevent the need from enabling this symbol at board or soc level.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
This PR is implementing a new formula to calculate the I2C timing
value from the I2C clock source and the bit rate.
This is done under flag CONFIG_I2C_STM32_V2_TIMING.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add STM32C0 SOC to combined interrupt config in order to
make it support the I2C driver.
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
Add I2C bus recovery support to the STM32 v1 and v2 driver. The STM32 i2c
peripheral does not natively support I2C bus recovery so recovery is
performed using GPIO bitbanging. This mirrors the bus recovery
implementation for NXP MCUX LPI2C driver.
Fixes: zephyrproject-rtos#54917
Signed-off-by: Maxmillion McLaughlin <github@maxmclau.com>
Update i2c drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on devicetree.
We remove 'depend on' Kconfig for symbols that would be implied by
the devicetree node existing.
Signed-off-by: Kumar Gala <galak@kernel.org>
Updates the API and types to match updated I2C terminology. Replaces master
with controller and slave with target.
Updates all drivers to match the changed macros, types, and API signatures.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Some text in help section was documenting the compatibility of driver
variants with stm32 series.
This is duplicate of information versus device tree which should be
used as single source of information for hardware description.
Remove these lines, so we don't have to touch this driver each time
a series is added.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add some simple depends so we limit various I2C drivers to the SoC
families that the drivers are relevant to.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use compatible information to configure i2c stm32.
With this, driver version selection is done thanks to compatible
and it is not needed anymore to do this via Kconfig symbol
selection under soc/
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
I2C interrupts usage should be the preferred way. This commit
enables them by default in the STM32 I2C driver itself.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Now that all I2C drivers utilize DTS we can select HAS_DTS_I2C in a
common place and don't need to do it per driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support of I2C. Add I2C5 configuration for the
arduino connector support.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@linaro.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@linaro.org>
Kconfig symbols I2C_STM32_V1 and I2C_STM32_V2 depends on SoC reference
and user should not have the possibility to choose one or the other.
Remove prompt on these symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
This is basically reapplying commit 133a299b50 ("drivers: i2c: Kconfig:
Remove redundant 'default n' properties"), which has been partially
reverted in commit c7875b75aa ("i2c: stm32_v2: implement slave
support").
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The STM32F7 uses the V2 version of the STM32 I2C controller. Add the
corresponding Kconfig, DTS, DTS fixup and pinmux entries.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This patch adds I2C Slave support conforming to the syscalls and funcs,
only for the STM32 V2 I2C Driver for the moment.
It is capable of handling multi-master bus setups.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Move driver specific to dedicated file when relevant (i.e.: more than
1-2 options), use if/endif also.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fabrice DJIATSA