Add support for configuring Ethernet pins using DT pinctrl entries. Note
that F1 series pinctrl support is not handled as the driver does not
support F1.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This commit enables support for parsing 'fixed-link' node when it
is added to node described in 'ethernet,fixed-link.yaml'.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch adds description for 'fixed-link' node in ethernet DTS
node. It supports setting speed and duplex.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add definition of zephyr,random-mac-address property that conveys to a
driver to utilize a random MAC address if the driver supports this
feature.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked sam_gmac driver to get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from soc_pinmap.h that are no longer needed due to
getting all that information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This add the following options to GMAC device tree bindings:
- max-frame-size
- max-speed
- phy-connection-type
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Ethernet MAC present in Silicon Labs EFM32GG11B4xx and
EFM32GG11B8xx SoCs.
DMA based driver with support for link up/down detection.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
Add any useful information from 'title:' to the 'description:' strings
(e.g. explanations of acronyms), and remove 'title:' as well as any
copy-pasted "this binding gives a ..." boilerplate.
Also clean some description strings up a bit.
Some other things could probably be cleaned up (replacing 'GPIO node'
with 'GPIO controller' on controllers for consistency, for example), but
I kept things close to the original to avoid accidentally messing up.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
With https://github.com/zephyrproject-rtos/zephyr/pull/20185, multi-line
descriptions will be formatted nicely, but using '>' breaks it, because
it removes internal newlines (including between paragraphs).
See https://yaml-multiline.info/.
Replace 'description: >' with 'description: |' to encourage '|'. That'll
prevent '>' from getting copied around and messing up long descriptions.
This will lead to some extra newlines in the output, but it's fine.
Line-wrapping messes up any manual formatting.
The replacement was done with
$ git ls-files 'dts/bindings/*.yaml' | \
xargs sed -i 's/description:\s*>/description: |/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Instead of
properties:
compatible:
constraint: "foo"
, just have
compatible: "foo"
at the top level of the binding.
For backwards compatibility, the old 'properties: compatible: ...' form
is still accepted for now, and is treated the same as a single-element
'compatible:'.
The old syntax was inspired by dt-schema (though it isn't
dt-schema-compatible), which is in turn a thin wrapper around
json-schema (the idea is to transform .dts files into YAML and then
verify them).
Maybe the idea was to gradually switch the syntax over to dt-schema and
then be able to use unmodified dt-schema bindings, but dt-schema is
really a different kind of tool (a completely standalone linter), and
works very differently from our stuff (see schemas/dt-core.yaml in the
dt-schema repo to get an idea of just how differently).
Better to keep it simple.
This commit also piggybacks some clarifications to the binding template
re. '#cells:'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The 'category: required/optional' setting for properties is just a
yes/no thing. Using a boolean makes it clearer, so have
'required: true/false' instead.
Print a clear error when 'category:' is used:
edtlib.EDTError: please put 'required: true' instead of 'category:
required' in 'properties: foo: ...' in
test-bindings/sub-node-parent.yaml - 'category' has been removed
The old scripts in scripts/dts/ ignore this setting, and only print a
warning if 'category: required' in an inherited binding is changed to
'category: optional'. Remove that code, since the new scripts already
have the same check.
The replacement was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i \
-e 's/category:\s*required/required: true/' \
-e 's/category:\s*optional/required: false/'
dts/binding-template.yaml is updated as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Sanity-checking each !included file separately was inherited from the
old scripts. It makes it messy to check that combinations of fields make
sense, e.g. to check 'const:' or 'default:' against 'type:', since those
fields might come from different files (this is handy, since it makes
sense to just add/change a 'const:' value, for example).
Drop the requirement that each !included file is a complete binding in
itself, and treat them as binding fragments instead. Only check the
final merged binding.
This also means that !included files no longer need to have a
'description:' or 'title:' (those have always been unused for !included
files), so remove those, and add comments that explain what the
fragments are for instead. That should demystify bindings a bit.
Also fix the descriptions of i2c.yaml, i2s.yaml, spi.yaml, and
uart.yaml. They're for controllers, not devices. These are copy-paste
error from the corresponding device .yaml files.
Piggyback some indentation consistency nits in binding-template.yaml.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Convert type from compound to phandle-array for various bindings that
have properties like like <FOO>-gpios, pwms, clocks,
interrupt-extended, etc. that are phandle-array's.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
the microchip,mcp2515 and microchip,enc28j60 bindings would hit the
following build error:
device tree error: dts/bindings/can/microchip,mcp2515.yaml (in 'reg'):
'category' from !included file overwritten
('required' replaced with 'optional')
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Same deal as in commit eba81c6e54 ("yaml: Remove redundant document
separators"), for some newly added stuff.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
No binding has anything but 'version: 0.1', and the code in scripts/dts/
never does anything with it except print a warning if it isn't there.
It's undocumented what it means.
I suspect it's overkill if it's meant to be the binding format version.
If we'd need to tell different versions from each other, we could change
some other minor thing in the format, and it probably won't be needed.
Remove the 'version' fields from the bindings and the warning from the
scripts/dts/ scripts.
The new device tree script will give an error when unknown fields appear
in bindings.
The deletion was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i '/^\s*version: /d'
Some blank lines at the beginning of bindings were removed as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Now that the generation script doesn't look at the "generation" in the
YAML, we can remove it from the binding files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
YAML document separators are needed e.g. when doing
$ cat doc1.yaml doc2.yaml | <parser>
For the bindings, we never parse concatenated documents. Assume we don't
for any other .yaml files either.
Having document separators in e.g. base.yaml makes !include a bit
confusing, since the !included files are merged and not separate
documents (the merging is done in Python code though, so it makes no
difference for behavior).
The replacement was done with
$ git ls-files '*.yaml' | \
xargs sed -i -e '${/\s*\.\.\.\s*/d;}' -e 's/^\s*---\s*$//'
First pattern removes ... at the end of files, second pattern clears a
line with a lone --- on it.
Some redundant blank lines at the end of files were cleared with
$ git ls-files '*.yaml' | xargs sed -i '${/^\s*$/d}'
This is more about making sure people can understand why every part of a
binding is there than about removing some text.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Introduce uint8-array type for local-mac-address as we need to
distinguish it from 'array' meaning a uint32 array.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common properties like 'compatible', 'reg', 'reg-names',
'interrupts', 'interrupt-names', and 'label' into one common base.yaml
that all the other yaml's can inherit from. This removes both
duplication and inconsistent definition.
The device specific yamls just need to say if a property is 'required'
or not.
NOTE: due to some generation conflicts we did not covert
'soc-nv-flash.yaml' to use base.yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get the following warning:
extract_dts_includes.py: WARNING: id field set in
'SMSC/Microchip LAN9220 Ethernet controller', should be
removed.
Removed the id: field to fix.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The board has SMSC LAN9220 (actually as an "IP core" in an
FPGA-emulated SoC). The patch includes DTS bindings for this device.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Driver for networking device Microchip ENC28J60 is used as SPI slave,
moved to DTS type definition. Samples echo_client and echo_server use
this device on Arduino 101 board.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Kinetis device K64F's PTP interrupt crashed the system becase it was not
generated from dts. Device interrupt correctly set now.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Partially replaces Kinetis MCUX driver configuration from Kconfig to
Device Tree. Interrputs moved from defines configuration to DT.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
The 'id' field was never used and tended to just have the compat of the
node. Lets remove it and removed some code in extract_dts_includes.py
related to it. Added a warning if 'id' is set in a yaml so we can
remove it going forward.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Gerard Marull-Paretas