Use the reschedule solution as there may be cases where a newer
deadline should supersede an older one.
The implementation has no locking and so has data races between the
handler and external events. Emit a console diagnostic in one case
where the race can be detected.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
All dma drivers are devicetree based now so we can remove the last
bits of Kconfig associated with the old driver style.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace device_get_binding with DEVICE_DT_GET for getting access
to the io-channels/adc controller device.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add an object to retain data across both reboots and entry to
SYSTEM_OFF. This only works on nRF52, since nRF51 and nRF53 require
different low-level operations to configure RAM retention.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Enable PECI and KSCAN drivers to evaluate any side-effect
in LPM entry/exit and power consumption.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
This commit adds the nRF IEEE 802.15.4 Service Layer Fault Handler
to the 802154_rpmsg sample.
Signed-off-by: Czeslaw Makarski <Czeslaw.Makarski@nordicsemi.no>
Simplify pm subsystem removing PM_STATE_LOCK option. Constraints API is
small and is a key component of power subsystem.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The sample was failing twister test with a timeout because there was
no pass/fail criteria for it (nothing was tested). The fix adds
harness on consolse and some output that can be verified.
Signed-off-by: Maciej Perkowski <Maciej.Perkowski@nordicsemi.no>
In the last step of the example, the system should go into soft off
state in order to match the original intent in the example to go
into the hardware's SHUTDOWN mode.
Fixes#31727
Signed-off-by: Vincent Wan <vanti.coder@gmail.com>
Change subsystem to use struct pm_state with substate-id instead of
using only the power state category.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Migrate the whole pm subsystem to use new power states information
from power_state.h and get states and residency properties from
device tree.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Provide a demonstration of using the timeutil skew infrastructure to
measure the relative error of the two clock sources on Nordic boards.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Conditionally use either DPPI or PPI channel in the sample so that
it can be built for all nRF SoCs. Update documentation accordingly.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Get rid of weak functions adding a new API to register an object to
receive notifications when the system changes power state.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
some tests configured with CONFIG_NEWLIB_LIBC=y,
it's better to add a filter filter: TOOLCHAIN_HAS_NEWLIB == 1
in those tests yaml file.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
- Remove SYS_ prefix
- shorten POWER_MANAGEMENT to just PM
- DEVICE_POWER_MANAGEMENT -> PM_DEVICE
and use PM_ as the prefix for all PM related Kconfigs
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The sample referenced the ADC through an alias that either never
existed or (more likely) has since been removed. Use the node label
instead.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Samples that include floating-point format specifications may need
cbprintf FP support. Make sure it's available.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Basic sample program that uses the one led and button from the Pinetime.
Led will turn on everytime the button is pushed.
Signed-off-by: Rafa Couto <caligari@treboada.net>
To make it runnable in the sanitycheck necessary to add
capture output, because that sample runs infinite period of time
and can not finished by itself. To avoid timeout error
in the sanitycheck I added capture output for a several times.
Also added one more tag to describe that it is a power
management sample.
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Moves mesh feature configuration to a separate module, deprecating the
bt_mesh_cfg_srv structure. The initial values for the features should
now be enabled through KConfig, where new config entries have been added
for each feature.
This removes the upward dependency on the config server from the core
stack, and makes the config server a pure frontend for the configuration
states, as all spec mandated behavior around the feature states is now
encapsulated.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Removes text from the readme of the onoff_level_lighting_vnd_app
claiming buttons control the LEDs before provisioning, as it's not
accurate.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Power management sample for that board has very
confusing name that should be changed to something
more understandable.
Current name sample.board.sample.board.mec15xxevb_assy6853
I suggest to have new name
sample.board.power_management.mec15xxevb_assy6853
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Replace all calls to the assert macro that comes from libc by calls to
__ASSERT_NO_MSG(). This is usefull as the former might be different
depending on the libc used and the later can be customized to reduce
flash footprint.
Signed-off-by: Xavier Chapron <xavier.chapron@stimio.fr>
HID API has changed and now all usb HID callbacks require
pointer to device as a first parameter. This patch is fixing
regression issue.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
-Wimplicit-fallthrough=2 requires a fallthrough comment or a compiler
to tells gcc that this happens intentionally.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This patch removes unused Kconfig option from console
subsystem. If application wants to wait until the console
port is connected, enabled and ready to receive data
it should use uart_line_ctrl_get() API function and
check for DTR flag.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
usb_enable() must be called once by the application.
The application may want to register usb_dc_status_callback
and trace usb status codes (usb_dc_status_code).
After this patch all pre APPLICATION messages will be dropped
as USB console device is enabled in the application.
Application waits for console device until its ready by checking DTR
flag - uart_line_ctrl_get(). This function could be dropped but then
some log messages that were generated before USB device is ready
could also be dropped.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
There is an additional prj_smp_svr.conf configuration file provided,
which builds an image with mcuboot support. Enable it in sample.yaml,
so sanitycheck can detect build failures in future.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
There is an optional mcumgr enabled prj_smp_svr.conf configuration
file. Using it results in following errors:
.../src/smp_svr.c:12:10: fatal error: mgmt/buf.h: No such file or \
directory
12 | #include <mgmt/buf.h>
|
Fix include paths to keep sample buildable with mcumgr enabled.
Fixes: c200b1c5e6 ("mgmt: Move mcumgr into its own folder")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Fix smp_svr Bluetooth configuration for when BT_HCI_ACL_FLOW_CONTROL
option has been enabled. In this case the CONFIG_BT_L2CAP_RX_MTU
is used instead of CONFIG_BT_RX_BUF_LEN to set the RX MTU.
This lead to a negotiated MTU of 23, which is not supported by
the SMP_SVP protocol.
Removed the board specific configuration files as these are just
duplications of the overlay-bt.conf or overlay-bt-tiny.conf and
the readme specifies how these should be used.
Reduced the TX MTU to end up with the same value as the RX MTU,
CONFIG_BT_RX_BUF_LEN - 4 (HCI ACL header) - 4 (L2CAP header).
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Peter Bigot