If CS (Chip Select, known also as Slave Select...) is managed externaly
of the stm32_ll SPI controller, just config NSS line management
accordingly.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add a SPI master and slave driver for the L4, F4 and F3 STM32
SoCs families.
Change-Id: I1faf5c97f992c91eba852fd126e7d3b83158993d
Origin: Original
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Tested-by: Lee Jones <lee.jones@linaro.org>
Now that we have a more generic mcux spi driver that can be used across
multiple Kinetis SoCs, remove the specific k64 spi driver.
Jira: ZEP-1374
Change-Id: Ifc324374f305837f5e3d2cfd7ad30d3608865b5b
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Support for Freescale/NXP K64 SPI modules, limited to:
- Master mode
- A single active set of clock and transfer attributes (CTAR0), which
includes non-adjustable delay parameters
- Tx FIFO fill and Rx FIFO drain interrupt handling
- Standard, continuous select and continuous SCK SPI transfer formats
Also, divide-by-zero code generation in this driver is prevented.
The 'volatile' attribute is added to some of the variables in the baud
rate and delay calculation functions of the K64 SPI driver in order to
prevent bad code generation by gcc toolchains for ARM seen when an
optimization setting above -O0 is used.
Specifically, a register is loaded with the constant 0 and is used as
the divisor in a following divide instruction, resulting in a
divide-by-zero exception.
This issue has been seen with gcc versions 4.8.1 (the VxWorks toolchain)
and 5.2.0 (the Zephyr SDK toolchain).
Change-Id: Ib5b2b748aad8fdfd5e8d40544e6e1abef3713abe
Signed-off-by: Jeff Blais <jeff.blais@windriver.com>
Adds extern "C" { } blocks to header files so that they can be
safely used by C++ source files.
Change-Id: Ia4db0c36a5dac5d3de351184a297d2af0df64532
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Change all the Intel and Wind River code license from BSD-3 to Apache 2.
Change-Id: Id8be2c1c161a06ea8a0b9f38e17660e11dbb384b
Signed-off-by: Javier B Perez Hernandez <javier.b.perez.hernandez@linux.intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Since the driver is the only one needing those, no need to expose them
anywhere.
Change-Id: Iac4eaa65a9dbdaa8e72c70ea0de35cd2b3d836d1
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This was failing, the documentationg provides numbers only telling at
one places these are hexadecimal values. So switching to hexadecimal.
Then DDS rate retrieving macro was bogus, so fixing it.
And adding debug output about the DDS rate and the clock ratio.
Change-Id: I9cc414796fbd7f7123f1f406c6bce7ffacf641e8
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is specific to Galileo board where its SPI port 0 needs to setup
the CS pin through a GPIO pin.
Change-Id: I9df6f7144a96bcd10f61fc7d057f89caa0e599d1
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Without it, it won't go through a pci scan, and will just trust the
pre-set information for the bus/dev/function to enable the memory
mapped registers.
Change-Id: Ica9156be541619dce9684dd45f70e05b69782a7c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Such controllers are found in Quark's X1000 series, and thus are found
on Galileo boards v1 and v2.
Change-Id: Ib71486c9f27de1b6c48ce3cb3dd138d69833c2ea
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Tomasz Bursztyka