Add configuration, pinmux, dts and documentation for the STM32L476G
Discovery board based on the STM32L476VG SoC.
Signed-off-by: Arthur SFEZ <arthur.sfez@gmail.com>
Adds the mimxrt1052 SoC, which belongs to a new family (nxp_imx) and
series (rt) of SoCs. The mimxrt1052 integrates an Arm Cortex-M7 core,
512 KB TCM, and many peripherals including 2D graphics, an LCD display
controller, camera interface, SPDIF and I2S. Unlike other SoCs in
Zephyr, the mimxrt1052 has no internal flash.
This initial port to mimxrt1052 configures the system clock to operate
at 528 MHz, and enables the serial/uart and gpio interfaces to support
the hello_world and blinky samples. Support for additional Zephyr driver
interfaces will come later.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Move the dts files into the board dir so that board ports can be more
standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the dts fixup files into the board dir so that board ports can be
more standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If DTS does not depend on include paths determined in /ext then we can
move dts next to kconfig. Moving it next to kconfig means that DTS
CONFIG_ variables will be available at the same time as kconfig's
CONFIG_ variables which is the intended design and beneficial from a
usability perspective.
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Boot serial recovery feature consume additional
memory size so the mcuboot partition must been
expanded on cost of images partitions.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Boot serial recovery feature consume additional
memory size so the mcuboot partition must been
expanded on cost of images partitions.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add board configuration, dts and pinmux, based on
arm/stm32f4_disco and arm/nucleo_f411re boards.
Error free tests are executed on eval board with the following
sample applications:
- hello_world
- blinky-sample
- button-sample
- console_echo_sample
- console_getchar_sample
Signed-off-by: Jose F. Fernandez <jffernandez@fenix-es.com>
Moved yaml files to be under dts/bindings and have the bindings try
and match the linux doc device tree binding dir structure as the
canonical binding reference.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added I2C bus (TWI) driver for Atmel SAM MCU family. Only
I2C Master Mode with 7 bit addressing is currently supported.
Tested on Arduino Due board.
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Adds device tree bindings for the Kinetis System Integration Module
(SIM), and defines peripheral source clocks (e.g., system clock or bus
clock) and clock gates for all Kinetis SoCs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds support for TI Simplelink MSP-EXP432P401R-LAUNCHXL
development board based on Cortex M4 family
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds support for on board UART_0 on MSP-EXP432P401R-LAUNCHXL.
Driver makes use of driverlib available in ROM by default, thus saving
code space.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The EFM32 Wonder Gecko Starter Kit contains sensors and
peripherals demonstarting the usage of the EFM32WG MCU
family. This patch add basic support for this board.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Silicon Labs EFM32 Wonder Gecko MCU includes:
* Cortex-M4F core at 48MHz
* up to 256KB of flash and 32KB of RAM
* USB with host and OTG support
* multiple low power peripherals
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
stm32f407 SoC is an extension of stm32f405 SoC with additional
support of ethernet and DCMI. Hence, in dts description, this
should be represented by stm32f407.dtsi including stm32f405.dtsi.
The opposite was proposed today in stm32 .dtsi files.
This commit fixes the inclusion model and renames
stm32f407-pinctrl.dtsi into stm32f405-pinctrl.dtsi
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This makes the SoC flash compatible with the common nonvolatile flash
YAML schema, and provides a write alignment. It mirrors work done on
nRF chips for the DFU subsystem.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This makes the SoC flash compatible with the common nonvolatile flash
YAML schema, and provides a write alignment. It mirrors work done on
nRF chips for the DFU subsystem.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This makes the SoC flash compatible with the common nonvolatile flash
YAML schema, and provides a write alignment. It mirrors work done on
nRF chips for the DFU subsystem.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This patch adds partition for NFFS for nRF51, nRF52 and nRF52840.
The partition is placed at the end of flash. This is only added if NFFS
is enabled (since it's required) - in other case free space can be used
for other purposes.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Similar addition was don previous for nRF52840.
Added flash-controller description and moved flash description to
it. Added property for description of
the flash alignment required by write operations.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Similar addition was don previous for nRF52840.
Added flash-controller description and moved flash description to
it. Added property for description of
the flash alignment required by write operations.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Remove usart2_pins_b as this configuration is not possible
(PA15 could not be mapped on USART2).
Besides usart2_pins_c as this configuration is not used yet,
remove to reserve "usart2_pins_c" for future use
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Default configuration for USART1 (Console output) on board
stm32f3_disco was set on PA9/PA10, which matches Rev-A/B
configuration. Though, on more recent configuration of the
board (Rev-C onward). USART1 is mapped to PC4/PC5.
This configuration has the benefit to support VCP, hence it
is chosen to be set by default.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add board configuration, dts and pinmux based on both
stm32f469i_disco board and nucleo_f412zg board
Signed-off-by: Massimiliano Cialdi <massimiliano.cialdi@powersoft.it>
Fixes uart irq info in the device tree fixup files for frdm_k64f and
hexiwear_k64. They were incorrect in uart instance 5.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch enables I2C_2 support for 96b_carbon. Without
this patch, trying to build I2C_2 will result in build
error.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Added flash-controller description and moved flash description to
it (for coherence). Added property for description of
the flash alignment required by write operations.
Thanks to that l-value FLASH_WRITE_BLOCK_SIZE macro
will be generated. It is useful for any component uses
the flash.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
We use UART1 for UART pipe in a number of qemu tests, so lets do the
same thing for the bluetooth test and move the bluetooth uart to UART2.
Jira: ZEP-2412.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Neil Armstrong