The code was setting the interrupt priority to 1 for each
vector to start. But I think it might be more appropriate
to set it to the LOWEST priority. Some ARCs will have
upwards to 15 priorities.
Change-Id: I9330ec8df323fe04ba0751faaafa39694f012364
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Convert leading whitespace into tabs in Kconfig files. Also replaced
double spaces between config and <prompt>.
Change-Id: I341c718ecf4143529b477c239bbde88e18f37062
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Provide functions of saving and restoring LOAPIC
states to support deep sleep.
Jira: ZEP-223
Change-Id: I1fb427989b021ec8e3a4f6dd0f4766a214360621
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Save and restore IOAPIC flags and irq to vector translation
info for supporting deep sleep.
Jira: ZEP-223
Change-Id: Ifc50a5a72699ff6782ad194d8e96b18fac34da18
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
In scenarios where device PM is enabled and dynamic irqs are
used, move the irq to vector table to RAM and keep it updated,
so that we can use this to restore IOAPIC/LOAPIC vector entries.
Jira: ZEP-224
Change-Id: I0d4350d4e30f8ca337a2a1d4f012748c3cb450f4
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Some ARC targets can have a data-cache. Although there is no special
instruction to clear exceptions during early init, it is necessary to
invalidate the d-cache BEFORE any data is fetched. The ARC on arduino 101
doesn't have d-cache, and will thus skip this d-cache invalidate.
Also, it is important to set the vector table base register to point to
the interrupt vector table EARLY, so that if an exception is encountered,
the correct vector table is found. Set this base only if it is found to be
different from the one compiled in to the code.
These initialization steps assure that proper exception handling
is in place during early init.
Change-Id: Ie8b5928e5813e104680a6d6510c85d32dc8ed8f3
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Use SOC_SERIES_* for naming SoCs with similar features and architectures
with the goal of code reuse. The Series in the config variable should avoid
name collisions and clearly denote the relationships within an SoC family.
Change-Id: I7a98542f96b5d5dc3acc23782c4d45f98cceb599
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use CONFIG_SOC_FAMILY for the top level SoC family. A family
will have different SoCs or different SoC series with multiple
SoCs.
Adding the Family string to the config variable to avoid confusion
between actual SoCs and families and to prevent name collisions.
Change-Id: Ic99a2c1df7850dee3a45641027af82464dd6fadb
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Introcuce a driver for External Interrupt/Event Controller (EXTI) found
on STM32 MCUs.
Change-Id: Ib206521fcc51b5dfaaf5dea9d436f8304f3a36be
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Make this explicit to conform to the abstraction layer
defined in include/irq.h
This only worked before because the preprocessor was
substituting the function prototypes.
Change-Id: Id4d46b01f1c53c3a942772640023e23796eeb43b
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Having priority levels 0 and 1 reserved on x86 due to implementation
details on how the CPU uses the vector table is confusing to users,
and makes it unnecessarily difficult to share drivers between arches.
Now on x86, priority levels 0 and 1 are available. Semantically, all
priority levels have had 2 subtracted from them.
It is no longer necessary to specify a priority level when the
vector itself is specified. If an IDT entry has a specific vector
associated with it, any priority argument is simply ignored.
In gen_idt, some simplifications have been made:
- The printed representation of a generated entry now fits on one line
- Some checks being done in validate_priority() were redundant, as
generate_interrupt_vector_bitmap() also ensures that there are
sufficient free vectors within a priority level.
Change-Id: I26669d8ee0a53f48fbc2283490a8c42d8b1daf8e
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
It's not a function and requires all its arguments to be build-time
constants. Make this more obvious to the end user to ease confusion.
Change-Id: I64107cf4d9db9f0e853026ce78e477060570fe6f
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Mostly SoC initialization and some kernel subsystems, but also some
device drivers like the interrupt controllers.
Change-Id: I8dc1844c33acd877c075b6b03558fdca6f87500b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This is the last step before obsoleting DEVICE_DEFINE() and
DEVICE_INIT_CONFIG_DEFINE().
Change-Id: Ica4257662969048083ab9839872b4b437b8b351b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_DEFINE() so that it fits in the 'device' namespace.
Change-Id: I3af3a39cf9154359b31d22729d0db9f710cd202b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_INIT_CONFIG_DEFINE(), because (a) it was not fitting
in any namespace and (b) it is not used to declare, but rather define a
object.
Change-Id: I1da5822f06b85a9fb024b5b184afd0ccc01012ec
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The interrupt API has been redesigned:
- irq_connect() for dynamic interrupts renamed to irq_connect_dynamic().
It will be used in situations where the new static irq_connect()
won't work, i.e. the value of arguments can't be computed at build time
- a new API for static interrupts replaces irq_connect(). it is used
exactly the same way as its dynamic counterpart. The old static irq
macros will be removed
- Separate stub assembly files are no longer needed as the stubs are now
generated inline with irq_connect()
ReST documentation updated for the changed API. Some detail about the
IDT in ROM added, and an oblique reference to the internal-only
_irq_handler_set() API removed; we don't talk about internal APIs in
the official documentation.
Change-Id: I280519993da0e0fe671eb537a876f67de33d3cd4
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This was never implemented on ARC/ARM and has been superseded
by irq_offload().
Some checks that were only done with CONFIG_LOAPIC_DEBUG fall
under the category of 'shouldn't ever happen' and have been
converted into assertions, instead of propagating return values
which are largely never checked.
Change-Id: I4eedca05bb7b384c4f3aa41a4f037f221f4a9cfe
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Use a real board name that can run this kernel instead of a generic
name. Basic functionality exits on this board with Zephyr.
Setup of the board is mostly similar to what we have in galileo (EFI
based)
Change-Id: Ic8554f26dcac0dbbbb6d35d863482f6207dc63c5
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
MVIC has only one local interrupt: the timer IRQ. What IRQ line
to use is not fixed, instead it is programmed into the LVTTIMER
register. This is unlike LOAPIC which has a fixed IRQ for the timer
and instead the *vector* to use for it is programmed into LVTTIMER.
We don't want _loapic_int_vec_set() to do anything as the relationship
between IRQ lines and vectors is fixed and we do not want to be
programming vector numbers into bits 0-3 of LVTTIMER.
The IRQ line to use for timer interrupts is programmed into LVTTIMER
when the MVIC is initialized.
Change-Id: Icba0429f65ece7541fa8542814a8fdc39ad43936
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Quark SE Lakemont core has a hardware bug where the LOAPIC does
not properly notify the IOAPIC to clear the IRR bit for level-
triggered interrupts.
This patch introduces a workaround where the vector ID of the
in-service interrupt is manually written to the IOAPIC_EOI
register, resulting in the bit being cleared.
Unfortunately, in the context where EOI happens it's very difficult
to identify which IRQ line is being serviced, so this is done
unconditionally for all interrupts vectors whether they are registered
in the IOAPIC RTE table or not.
Change-Id: I639cd258dec4f50934e17eadbb821e6a7112e636
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
A special situation may occur when a processor raises its task
priority to be greater than or equal to the level of the
interrupt for which the processor INTR signal is currently
being asserted. If at the time the INTA cycle is issued, the
interrupt that was to be dispensed has become masked (programmed
by software), the local APIC will deliver a spurious-interrupt
vector. Dispensing the spurious-interrupt vector does not affect
the ISR, so the handler for this vector should return without an EOI.
Change-Id: I4cf4744bd6efd68b72e2c380269de4181dc80bd9
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This was only needed for an older implementation of software interrupts,
now superseded by the irq_offload() API (which doesn't interact with
the interrupt controller at all)
Change-Id: I8aa696d370ae1799872f6d70de69f3cb5b47456a
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The initialization code and macros are the same. So extracts it
and puts it into the driver. This is another step to follow
the driver model.
Those empty C files are there because the current Kbuild
requires Makefile to be present at those directories,
(due to arch/x86/Kbuild), which requires building some object
files. So the empty source files are there to produce empty
object files to satisfy this.
Change-Id: I14056347ea14cff227d9e8960192e8673c0019b8
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The initialization code and macros are the same. So extracts it
and puts it into the driver. This is another step to follow
the driver model.
Change-Id: I1d379068f64855d5d4595838040ec50f97f638a0
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The initialization code and macros are the same. So extracts it
and puts it into the driver. This is another step to follow
the driver model.
Change-Id: I1af8b2888779b2b58367feaff9ee1a6d97b4873c
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Removed old style file description and documnetation and apply
doxygen synatx.
Change-Id: I3ac9f06d4f574bf3c79c6f6044cec3a7e2f6e4c8
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The kernel event logger requires this function to obtain
the irq that is being processed, but this was not implemented
for mvic. This patch add this function to mvic.
Change-Id: I5e1b4a6e2758b69ec713c18ac9f78aebad18a93f
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Do not depend on environment variables and use a kconfig variable
for defining the architecture.
In addition, remove the X86_32 variable, it just duplicates X86 for
not good reason, at least until start supporting MCUs with 64bit.
Change-Id: Ia001db81ed007e6a43f34506fed9be1345b88a4b
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This module is based on the standard Local APIC and IO APIC source modules.
This modules combines these modules into one source module that exports the
same APIs defined by the Local APIC and IO APIC header modules. These
routine have been adapted for the Quark D2000 Interrupt Controller which has
a cutdown implementation of the Local APIC & IO APIC register sets.
Change-Id: Ic80aa78918483663d76054ebadefa08d8a3f188a
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Flags allow passing IRQ triggering option for x86 architecture.
Each platform defines flags for a particular device and then
device driver uses them when registers the interrupt handler.
The change in API means that device drivers and sample
applications need to use the new API.
IRQ triggering configuration is now handled by device drivers
by using flags passed to interrupt registering API:
IRQ_CONNECT_STATIC() or irq_connect()
Change-Id: Ibc4312ea2b4032a2efc5b913c6389f780a2a11d1
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
We generally call this in interrupt code, and since it's just a register
write, get rid of all the function call overhead.
Change-Id: I251fa3cee0841fcdd8eecc7941d4d3782d112e66
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We are interested in supporting some XIP x86 platforms which are
unable to fetch CPU instructions from system RAM. This requires
refactoring our dynamic IRQ/exc code which currently synthesizes
assembly language instructions to create IRQ stubs on-the-fly.
Instead, a new approach is taken. Given that the configuration at
build time specifies the number of required stubs, use this
to generate a build time a set of tiny stub functions which simply
push a 'stub id' and then call common dynamic interrupt code.
The handler function and handler argument is saved in a table keyed by
this stub id.
CONFIG_EOI_HANDLER_SUPPORTED removed, the code hasn't been conditionally
compiled for some time and in all cases we call _loapic_eoi() when
finished with an interrupt.
Some other out-of-date verbiage in comments related to supporting
non-APIC removed.
Previously, when dynamic exceptions were created a pointer would
be passed in by the caller reserving ram for the stub code. Since
this is no longer feasible, two new Kconfig options have been added.
CONFIG_NUM_DYNAMIC_EXC_STUBS and CONFIG_NUM_DYNAMIC_EXC_NO_ERR_STUBS
control how many stubs are created for exceptions that push
an error code, and no error code, respectively.
SW Interrupts are no longer triggered by "int <vector>" hard-coded
assembly instructions. Instead this is done by sending a self-directed
inter-processor interrupt from the LOAPIC, using a new API
loapic_int_vect_trigger(). In this way we get rid of dynamically
generated code in irq_test_common.h.
All interrupts call _loapic_eoi() when finished, since this is now
the right thing to do for all IRQs, including SW interrupts.
_irq_handler_set() for x86 no longer requires the old function pointer
to be supplied.
Change-Id: I78993d3d00dd153c9051c518b417cce8d3acee9e
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
XIOAPIC_DIRECT_ADDRESSING and IOAPIC_MSI_REDIRECT are never
set and not tied to any config options.
Change-Id: Ib64cd198c99fe670eb5bcd946ce93f616c03d12a
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This was only needed for the older 8259A style PICs which are no
longer supported.
Since we now just support APIC, we always just call loapic_eoi which
no longer requires an argument and informs the IOAPIC that the interrupt
is complete if necessary.
Change-Id: I15c9b7b4f03b872656220af32220b62e043bfa6b
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Change-Id: I819d13f0d7a23e3a61dcda6a3ced18810b192158
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change-Id: I6da43e41f9c6efee577b70513ec368ae3cce0144
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Moving many of the functions from the old format of inline comments to
the newer doxygen format.
Change-Id: Ib0fe0d8627d7cd90219385a3ab627da8f9637d98
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Change all the Intel and Wind River code license from BSD-3 to Apache 2.
Change-Id: Id8be2c1c161a06ea8a0b9f38e17660e11dbb384b
Signed-off-by: Javier B Perez Hernandez <javier.b.perez.hernandez@linux.intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Change the IOAPIC driver to be initialized directly from the init
system. The function signature of _ioapic_init() function is updated
accordingly.
Change-Id: I2f824ac745926966eebb23f60445a41e1df9eb8f
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Change the LOAPIC driver to be initialized directly from the init
system. The function signature of _loapic_init() function is updated
accordingly.
Change-Id: I5ed26d53524c8526d413a05ac9a7a58dd4264c5a
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Change the PIC driver to be initialized by the init system. To be
initialized by the init system the function signature of the
_i8259_init() function needs to be changed to the standard *_init()
function signature specified by the device model.
Change-Id: I63bf1cd0ce78920fa20da94f5966e5aab4bf41b2
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Make config variable name match the function. The PIC is never turned
on in the zephyr code so there is nothing to shut off.
Change-Id: I1627e5a35cc37ef7959f36758c1e1aec03e22782
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
These x86 drivers are the last users of the PLB_* macros change to use
the sys_{in,out} functions.
Change-Id: Iebd0ad1bf5e74379498f86b24d835a0430db1311
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Chuck Jordan