Adds a new config HAS_MCUX_FTFX to conditionalize the mcux flash driver
on socs that support it. Selects HAS_MCUX_FTFX on all kinetis socs
except kw40z, because even though this soc has the relevant hardware,
its CMSIS header file is not compatible with the mcux flash driver in
ext/.
This change also prevents enabling the mcux flash driver on lpc and imx
rt boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This commit removes "select SYS_POWER_*_SUPPORTED" entries from
Kconfig on SoCs which are not implementing sys_set_power_state()
method used to control power mode.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The SYS_POWER_LOW_POWER_STATE_SUPPORTED and SYS_POWER_LOW_POWER_STATE
suggests one low power state but these options control multiple
low power state. This commit uses plural in the names to indicate
that.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The eth mcux driver has been using non DT_ prefixed defines for DT
generated defines. Switch to use DT_ prefixed ones as we want to
deprecated the non DT_ prefixed defines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that a hw-flow-control DTS binding has been added for MCUX uart,
let's check for the DT_ define and enable support in the MCUX HAL
layer.
Signed-off-by: Michael Scott <mike@foundries.io>
Adds a new config HAS_MCUX_ENET to constrain which socs can enable the
mcux ethernet driver. This will prevent users from enabling the driver
on socs like kl25z or kw41z which do not have ethernet mac hardware.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The early boot watchdog init for kinetis was incorrectly disabling and
reenabling interrupts to preserve timing during the unlock sequence.
However, interrupts are already disabled before this routine executes
and the kernel is not yet ready to enable them when this routine exits.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Declare and define nxp_mpu_config and nxp_mpu_regions
structs as const, as they are not modified in run-time.
Fixes#10320
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Kinetis device K64F's PTP interrupt crashed the system becase it was not
generated from dts. Device interrupt correctly set now.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
All drivers require DTS for their primary SPI settings.
Removing SPI_[0-9]_NAME config option added some more samples changes.
Usage of these options there was anyway not relevant.
Fixes#11064
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all SPI controllers support DTS we can remove the Kconfig
support for non-DTS options. We also cleanup some defines that should
have be DT_MCR20A_ instead of CONFIG_MCR20A_.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This can help find unused symbols. Those end up without a type if
'default' is used instead of 'def_bool', which generates a warning.
Search for "Kconfig.defconfig" in
https://docs.zephyrproject.org/latest/application/kconfig-tips.html for
a longer explanation.
Keep the 'def_bool' for the following symbols, which seem to be
deliberately defined only in Kconfig.defconfig files:
- ALTERA_AVALON_I2C
- ALTERA_AVALON_MSGDMA
- ALTERA_AVALON_PIO
- ALTERA_AVALON_QSPI
- ALTERA_AVALON_SYSID
- CLOCK_CONTROL_IMX_CCM
- CPU_EM4_DMIPS
- CPU_EM4_FPUDA
- CPU_EM4_FPUS
- FP_FPU_DA
- I2C_GECKO
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
All labels containing "_<8-hex-digits>_" or "16550_<3or6-hex-digits>_"
in their names, assumed to be generated by the extracting script,
are updated with the DT_ prefix, to reflect the recent changes made
to the script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add dts binding and info for TRNG device and enable basic support to
get the device name from DTS. We leave for now the base addresses
coming from the MCUX HAL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add dts binding and info for RNGA device and enable basic support to
get the device name from DTS. We leave for now the base addresses
coming from the MCUX HAL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Partially replaces Kinetis MCUX driver configuration from Kconfig to
Device Tree. Interrputs moved from defines configuration to DT.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This commit removes all MPU-related (ARM_CORE_MPU and NXP_MPU)
options exept ARM_MPU, which becomes master switch controlling
MPU support on ARM.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
This commit introduces CPU_HAS_ARM_MPU and CPU_HAS_NXP_MPU options,
which indicate which flavour of MPU is supported by given SoC family.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The HAS_SYSMPU option is just selecting NXP_MPU option,
which could be also controlled through menuconfig.
This commit removes the HAS_SYSMPU option and replaces
its usage by NXP_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
Move the SoC outside of the architecture tree and put them at the same
level as boards and architectures allowing both SoCs and boards to be
maintained outside the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Patrik Flykt