The device pm actions (low_power or suspend) were switched. Also,
added SOFT_OFF to the suspend action.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Suspend devices when the system goes to STATE_SOFT_OFF.
This state was not triggering any device power management. This should
at least suspend devices as it is done for SUSPEND_TO_RAM and
SUSPEND_TO_DISK.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Enables the dma driver on the mimxrt1064_evk board. The board
documentation is not updated because it already mentions dma driver
support.
Tested with:
- tests/drivers/dma/chan_blen_transfer
- tests/drivers/dma/chan_link_transfer
- tests/drivers/dma/loop_transfer
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables the watchdog driver on the mimxrt1064_evk board. The board
documentation is not updated because it already mentions watchdog driver
support.
Tested with tests/drivers/watchdog/wdt_basic_api
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
stm32cube: update stm32f1 to version V1.8.4
stm32cube: update stm32f2 to version V1.9.3
stm32cube: update stm32f4 to version V1.26.1 V1.26.2
stm32cube: cleanup stm32f7 version V1.16.1
stm32cube: update stm32g0 to version V1.5.0
stm32cube: update stm32wl to version V1.1.0
stm32cube: update stm32f0 to version V1.11.3
stm32cube: update stm32f3 to version V1.11.3
stm32cube: update stm32l0 to version V1.12.1
stm32cube: update stm32l1 to version V1.10.3
stm32cube: update stm32wb to version V1.12.0
(including ble library update)
stm32cube: common_ll: Regeneration after cube updates
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After update of stm32 cube l1 V1.10.3,
SPI_CR2_FRF doesn't exist for all stm32L1 MCU,
thus LL_SPI_SetStandard() is also not defined for all stm32l1 MCU.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Follow up on commit bfd45e5b8c
("drivers: remove Kconfig option CONFIG_UART_CONSOLE_ON_DEV_NAME")
Now we can also remove Kconfig option CONFIG_UART_CONSOLE_ON_DEV_NAME
since all UART drivers are converted to devicetree and we can just use
DEVICE_DT_GET(DT_CHOSEN(zephyr_shell_uart)).
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Commit c79b1a38aa ("samples: display:
Convert driver and lvgl sample.yaml to use depends_on") started using
depends_on in the sample YAML for a lvgl application instead of
platform_allow.
This breaks build testing with twister and overflow checking enabled
on more resource constrained platforms. The test case's .config
ends up with:
CONFIG_LVGL_HOR_RES_MAX=320
CONFIG_LVGL_VER_RES_MAX=240
CONFIG_LVGL_VDB_SIZE=64
CONFIG_LVGL_BITS_PER_PIXEL=24
And lib/gui/lvgl/lvgl.c, where we allocate a buffer of size:
(CONFIG_LVGL_BITS_PER_PIXEL *
((CONFIG_LVGL_VDB_SIZE * CONFIG_LVGL_HOR_RES_MAX *
CONFIG_LVGL_VER_RES_MAX) / 100)
/ 8)
Require 147456 bytes to build the sample, ultimately overflowing RAM
if you run something along the lines of:
twister -T samples -p <constrained_platform> --overflow-as-errors
This is a reasonable test to be doing to make sure that sample RAM
requirements do not get too big for a subset of platforms that are of
interest, and it no longer works.
To fix it, add a min_ram line for this case so that we can still run
overflow tests on a large set of samples without fine-grained special
casing or creating an ever-growing list of platform excludes for this
test.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The units for these testcase YAML fields are missing, making it
unclear how to use them. Fix it.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Using 3rd Party Toolchains page find out that warning message
can be moved to the top of the page.
Add Windows example in OneAPI.
Style fixing.
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
This adds basic support for the Silabs Si7210 hall effect magnetic
position and temperature sensor. It is able to get magnetic field and
temperature in the default scale of the sensor (depending on the
variant). It also supports going into sleep mode without measurements
through the device power management infrastructure.
It is most notably missing support for scale change, measurement
averaging and filtering, and alert pin configuration (threshold,
hysteris, tamper).
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
the correct value is returned when using sensor channel get function to
read z-axis value
Signed-off-by: Vojislav Milivojevic <milivojevicvoja@yahoo.com>
Move the implementation of scan trains after call to LLL
prepare, so that LLL prepare executes without any latency.
To increase radio utilization, LLL prepare should be
scheduled as early in the `ticker_cb` of the radio event.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix the return value use to indicate unassigned auxiliary
context when scanning is using LLL scheduling. This can
happen only under LLL scheduling where in LLL auxiliary
channel PDU reception has been spawn from LLL primary
channel scanning and on completion will join back to resume
primary channel PDU scanning.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Keep the default AD Data length to Bluetooth Specification
defined minimum of 31 octets.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
While reading the code, found some typos in the code comments,
line 226 and 668.
Fix comments to make it more solid.
Signed-off-by: Naiyuan Tian <naiyuan.tian@intel.com>
Reduce interval of warning timer, so we can print more
warning messages (ex. MEPC, task ID...) before watchdog reset.
Signed-off-by: Ruibin Chang <ruibin.chang@ite.com.tw>
We add disable event timer at the beginning of critical section
for two reason:
1.For K_TICKS_FOREVER case: since no future timer interrupts
are expected or required, so we disable the event timer.
2.Others case: according it81202 spec, when timer enable bit
from 0->1, the timer will reload counts and start countdown.
Signed-off-by: Ruibin Chang <ruibin.chang@ite.com.tw>
Update the connected ISO API to be more
similar to the broadcast ISO API as well
as the HCI spec.
This updated API allows for more flexibility
and will better support scenarios such as true
wireless setup, as ISO channels and connections
are more independent now.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Fix implementation to not to put back the primary channel
scanning to resume state when Extended Scan has used ULL
scheduling which pre-empts the scan window.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add Kconfig options that allow users to select the way the APPROTECT
mechanism is handled in the SystemInit() function.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Fixes accelerometer_handler.cc to import correct header
with TfLiteStatus since c_api_internal.h file was deleted in
the new standalone tflite-micro repo.
Removes import of version.h in main_functions.cc to match
tflite-micro version.
Signed-off-by: Lauren Murphy <lauren.murphy@intel.com>
Changes name of folder from tensorflow to tflite-micro and updates docs
to reference TensorFlow Lite Micro specifically instead of TensorFlow.
Signed-off-by: Lauren Murphy <lauren.murphy@intel.com>
Updates west manifest and module folder name to point to new
TensorFlow Lite Micro repo Google recently pulled out of
the TensorFlow repo.
Signed-off-by: Lauren Murphy <lauren.murphy@intel.com>
Suppress violation, because it is a deliberated deviation.
Noticed, that my previous PR #36420 comments were not correctly
detected by a static analysis tool. Only the first one item
"MISRAC2012-RULE_20_4-a" was detected and suppressed.
Change comment style, so each item will be suppressed.
Comment style defined in PR #36911 as the most suitable
for the analysis tool.
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Currently the default runner of nsim_hs_smp is mdb,
the runner of other nsim platform is nsimdrv, user
can't change the default runner unless he uses
west command(--runner).
With this change cmake will choose runner according
to BOARD_DEBUG_RUNNER or BOARD_FLASH_RUNNER. so if
add -DBOARD_FLASH_RUNNER=mdb-nsim or
-DBOARD_DEBUG_RUNNER=mdb-nsim to cmake command,
the apllication will be run with mdb.
Signed-off-by: Jingru Wang <jingru@synopsys.com>
Following change of HSE clock binding, remove hse-bypass
which is no longer an option and replace it with hse-tcxo
which is the configuration closest to previous status.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On STM32WL, HSE clock can take 2 specific options:
-hse-tcxo
-hse-div2
Enable support for these options.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32WL features a specific HSE clock with dedicated properties.
Add a dedicated binding and update STM32 clock control driver
header to take it into account.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move this to where priorities are being discussed to keep things in
context and to have all priority types documented in 1 place.
Fixes#21648
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Reapply the part of 4b5cd92312
that added new functionality/fixed the actual issues described
in the original commit message withtout the further cleanup.
There was also some cross-commit content from
2b91ebe16e
as part of the cleanup in test_friendship.c which is also included.
+ added cleanup also to test_provision.c on request from Aleksandr.
Original commit msg:
-----------
Multiple bsim devices cannot store individual settings
with the existing settings backend for bsim.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
-----------
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
This reverts commit 4b5cd92312.
global_device_nbr is used by many bsim tests.
And many of those are now off tree in preparation of the LE-Audio
work. Removing this for cleanliness now is not nice on others.
=> Revert
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The test checks the resistance of ble mesh stack to replay attack.
Replay protection cache shall store seqAuth last frames.
Device shall filter out such messages on the transport layer.
Power on\off sequence shouldn't impact that
since replay protection cache is stored in settings subsystem.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Flavio Ceolin