Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update the MCUX I2C driver and related platforms to get their I2C
information from the device tree. We also updated a few of the sensor
drivers found on the FRDM & Hexiwear boards to get their I2C bus name
from the device tree instead of directly from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds common and Kinetis-specific adc device tree properties, and updates
all Kinetis SoC and board dts files to include adc nodes.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Multiple Kinetis SoCs have the same lpuart hardware as the kw41z and can
use the same mcux driver, so rename the dts to be more generic.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Now that we can utilize label in the device tree we can convert to
getting the device name for the NXP Kinetis UART out of the device tree
instead of from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Devicetree.org specifies that serial devices property used to set
baud rate is "current-speed", while zephyr uses "baud-rate".
Align property name in order to keep zephyr dts files compatible
with device tree specification and could be re-used from/to
Linux for instance. We also cleanup a few SoCs that set "baud-rate" in
the SoC dts and not the board.
Jira: ZEP-2048
Change-Id: I097e7439ee46fe77c628b56531772950382fafcc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Recommend to drop the generic arm,nvic and just use arm,v{6,7,8}m-nvic.
Remove the yaml and switch to using arm,v6m-nvic or arm,v7m-nvic in the
various places.
Change-Id: Ide55d558d38ab247ee6d9a8d3d0a7f21b9c859bd
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As per new binding for arm,nvic, rename the 'num-irq-prio-bits' property
to 'arm,num-irq-priority-bits'.
Change-Id: I2182a905de340e134c67ac4aabe926fbb47c0d5a
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworking the ARM NVIC binding and cleaning it up. Towards this
introduce a new compatibility for this new binding. So we rename
arm,armv{6,7}-nvic to arm,v{6,7}-nvic (for new binding). We also just
use the bit more generic arm,nvic in device tree files.
Change-Id: I5a2c45313ed94619d9268f2c035dacbc8acded29
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move back to getting the number of IRQs from Kconfig. We do this
because the number of IRQs should really just be determined by scanning
the device tree and figuring out the highest IRQ value used.
Change-Id: I8e0dbec1d9d036d4e899b237c4dc7d833c422e18
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rather than having a zephyr specific property we will encode the IRQ
priority as part of the interrupt property for ARM NVIC based interrupt
controllers.
Change-Id: I7d1489f0bffa7a6369f0622f748bb70dc83fa0cd
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds the base DTS support for the KW41Z Freedom board. The
initial set of changes include SRAM, FLASH, IRQ controller and LPUART
support.
Change-Id: Ic68c4959ddad0c5cfe70d5576a0e58372b93ec9d
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Kumar Gala