This adds to the spi_loopback test board-specific configurations
for the following boards:
- nrf51_pca10028
- nrf52_pca10040
- nrf52840_pca10056
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
It was much more limited than the spi_loopback test, and of course using
the legacy API. Removing it then.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Instead of using CONFIG_POLL, which is not directly related to SPI and
is a kernel option, let's have SPI_ASYNC instead. When enabled, it will
select POLL automatically.
Fixes#5839
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
tx_bufs/tx_count and rx_bufs/rx_count can be hold in another dedicated
structure, thus reducing the number of parameters to transceive. This
permits to avoid using the stack when calling transceive.
Since we saved parameters, we can expose back the struct device pointer,
to stay consistent with other device driver APIs.
Fixes#5839
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
No need to verify that the configuration is proper if we are
compiling the driver for unit test and not going to ever run
the test.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
A new build test for gpio drivers is added to build_all testcase.yaml.
The gpio_sx1509 driver is enabled in the .conf file and dts.fixup macros
are added for the driver.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
The SAM0 SoC was switched to use DTS for SPI configuration. Adapt the
spi_loopback test configuration for the Arduino Zero to use the
correct device name.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add a testcase.yaml configuration to spi_loopback test to include
it into sanitycheck.
Fixes#4576
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This restores the board specific configurations that were present
before moving the test to using KConfig.
<board>.conf files from boards subdirectory get merged with
prj_base.conf file.
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
Convert this test to using KConfig instead of conditional compilation.
Standard configuration is provided by prj_base.conf and KConfig
default values.
Remove prj_<board>.conf files.
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
The introduction of device tree support sensors need to update the
dts.fixup file in build_all to make sure that we still build.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we have an application level dts fixup, we can re-enable the
fxos8700 sensor in the build_all test. Also added fxas21002 and max30101
sensors which were missing.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The following drivers are in the process of support getting their I2C
name, bus, address params from device tree. However if a given board
that supports device tree doesn't have one of these sensors we can't
build it.
To address this we add a dummy dts.fixup at the application level with
provides values for the defines we'd normally get from the dts
generation.
Fixes: #5722
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove SPI_*_IRQ_PRI from tests and samples.
Using DT to get the *_IRQ_PRI, we can't
override it using Kconfig.
If needed, use a BOARD_NAME.overlay file to
override default values.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This test should be blacklisted for any board based
on the POSIX arch, not just the native_posix board
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
This is just a build test, so make it part of the overall build test
instead of having a special test case for it.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Too much duplication in test structure, just call this api and being
under aio, explains that it is an API test for AIO.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The following 3 testcases are blacklisted for the POSIX
arch / simple_process BOARD:
* tests/drivers/ipm : won't compile due to missing
__stdout_hook_install() [part of minimal libc]
(POSIX arch uses the native libc)
* tests/kernel/mem_protect/stackprot : will crash
"natively" when trying to corrupt the stack and therefore
will fail the testcase. The current understanding is that
the POSIX arch should let the native OS handle faults,
so they can be debugged with the native tools.
* samples/cpp_synchronization : it is not possible
to build cpp code yet on top of the posix arch
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Testcase yaml requires some interactive inputs to be provided for
execution and hence fails on automation. Hence making it as build
only
Signed-off-by: ravishankar karkala Mallikarjunayya <ravix.shankar.km@intel.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
This should clear up some of the confusion with random number
generators and drivers that obtain entropy from the hardware. Also,
many hardware number generators have limited bandwidth, so it's natural
for their output to be only used for seeding a random number generator.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Anas Nashif