This introduces a new option that allows the user to disable the
subscription checking when notifying or indicating.
Some users might have use-cases where they would like to send notifications
or indications without the peer having to go through the subscription
process, as that is allowed by the Bluetooth specification.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
This API now becomes a low-level API, in the sense that it should only be
used if the app developer knows what he is doing and wants to ensure a
ATT_MULTIPLE_HANDLE_VALUE_NTF PDU goes on-air.
For the other 99% of use cases, `bt_gatt_notify` should instead be used, as
it will automatically upgrade to ATT_MULTIPLE_HANDLE_VALUE_NTF when
possible.
One can disable the batching of notifications when using `bt_gatt_notify`
by setting CONFIG_BT_GATT_NOTIFY_MULTIPLE_FLUSH_MS=0 .
This API doesn't support lookup by UUID any more.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
The intended behavior is that calling `gatt_notify_mult` in a loop will
result in a `BT_ATT_OP_NOTIFY_MULT` containing all the handles and their
data.
What was happening instead is that the caller thread was a lower priority
than the system workqueue, and thus multiple `BT_ATT_OP_NOTIFY_MULT` PDUs
were being sent over the air instead of one.
Submitting the work item with a delay side-steps this particular issue.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
Core Vol 3, Part G, Section 5.3.2 Channel Requirements states that
"The channel shall be encrypted". It does not mention any additional
security requirements that can be specified bt higher layer profiles.
This enables link encryption requirement for EATT channel.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
The automatic elevation of security and retry of ATT requests interferes
with some tests that expect authentication failures.
Affecting GATT/CL/GAR/BI-42-C
Signed-off-by: Herman Berget <herman.berget@nordicsemi.no>
EATT is not a requirement for the Multiple Variable Length Read
procedure, but previously one had to enable CONFIG_BT_EATT to enable
support for it.
Signed-off-by: Herman Berget <herman.berget@nordicsemi.no>
If the Kconfig BT_EATT_AUTO_CONNECT is enabled (on by default), the
host will try to connect BT_EATT_MAX EATT channels when a connection
to a peer is established.
Signed-off-by: Herman Berget <herman.berget@nordicsemi.no>
This adds support for automatic ATT MTU Exchange that will be done right
after the connection has been established.
Fixes: #43946
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
With the introduction of `EXPERIMENTAL` and `WARN_EXPERIMENTAL` in
Zephyr all subsys/bluetooth and drivers/bluetooth/hci settings having
`[EXPERIMENTAL]` in their prompt has has been updated to include
`select EXPERIMENTAL` so that developers can enable warnings when
experimental features are enabled.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Align with the new inclusive naming terms in the v5.3 spec in the
Bluetooth Host implementation.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Some centrals deal poorly with receiving a security request immediately
after reconnection whenever reconnecting with characteristics that are
notifiable or indicatable and requiring security. In particular,
Android 9 and earlier devices may lose bond information when this
happens, some Microsoft Surface devices will enter an invalid state
and, on top of that, Apple's Bluetooth Low Energy guidelines explicitly
discourage this behavior.
In order to allow interoperability with those devices, make the GATT
automatic security request sending as a peripheral optional by
introducing a new Kconfig option, BT_GATT_AUTO_SEC_REQ.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Refactor and simplify the bluetooth buffer configurations to improve the
easy of configurations and eliminate invalid ones.
By moving configurations out of host and controller specific
configurations and into a common one it becomes easier to configure
the host and controller separately as the same configurations can be
used as would be for a combined build.
All HCI configurations are now given exluding the matching HCI header,
which eases the configuration as the application don't have to know the
different header sizes.
The BT_RX_BUF_LEN is split into ACL and Event, as well as the suprising
use of Command size.
BT_L2CAP_RX_MTU is removed as the stack does not support reassembling of
HCI ACL data to larger L2CAP PDUs. The application will have to set
ACL RX size and account for the L2CAP PDU header itself.
BT_EATT_RX_MTU was removed as it is only used for setting a different
default value for another option which leads to the stuck kconfig symbol
problem.
The configurations can be updated according to the table below:
** New configuration | ** Old configuration
All configurations
BT_BUF_ACL_RX_SIZE | BT_L2CAP_RX_MTU + 4
BT_BUF_ACL_RX_SIZE | BT_RX_BUF_LEN - 4
BT_BUF_EVT_RX_SIZE | BT_RX_BUF_LEN - 2
BT_BUF_CMD_TX_SIZE | BT_RX_BUF_LEN - 3
BT_BUF_CMD_TX_COUNT | BT_HCI_CMD_COUNT
BT_BUF_EVT_RX_COUNT | BT_RX_BUF_COUNT
BT_BUF_ACL_RX_COUNT | BT_RX_BUF_COUNT
BT_BUF_ACL_RX_COUNT | BT_ACL_RX_COUNT
BT_BUF_EVT_DISCARDABLE_SIZE | BT_DISCARDABLE_BUF_SIZE - 2
BT_BUF_EVT_DISCARDABLE_COUNT | BT_DISCARDABLE_BUF_COUNT
Controller-build
BT_BUF_ACL_TX_SIZE | BT_CTLR_TX_BUFFERS_SIZE
BT_BUF_ACL_TX_COUNT | BT_CTLR_TX_BUFFER
HCI-bridge
BT_BUF_ACL_TX_SIZE | BT_HCI_ACL_DATA_SIZE
BT_BUF_ACL_TX_COUNT | 6
Fixed invalid configurations setting either BT_L2CAP_RX_MTU or
BT_CTLR_DATA_LENGTH_MAX larger than BT_RX_BUF_LEN could lead to buffer
overruns.
Fix advertising report max data length calculation.
This always used the BT_DISCARDABLE_BUF_SIZE macro but this feature
can be turned off and advertising reports will be allocated from the RX
buffer in that case. Also controller-build does not have this buffer
(in hci_raw.c). Also the wrong HCI header was used in the calculation,
HCI event header should have been used instead of HCI ACL header.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
In the file gatt.c, GAP service contains the Device Name
characteristic. If writable, authentication and authorization may
be defined by a higher layer specification.It means that GATT
clients can write to device name GAP characteristic without
bonding. So we add a configuration for writable name without
bonding.
Signed-off-by: Jun Huang <huangjun6@xiaomi.com>
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
ATT channels do support queueing buffer so it no longer need to block
waiting the tx_sem besides the buffer allocation already serves the
same purpose as the application will not be able to have more requests
than there are buffers available.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Allow application to enable L2CAP dynamic channels without support
for Enhanced Credit Based Flow Control (CBFC).
Since these are separate features in the qualification it should
be possible to qualify L2CAP connection oriented channels without
also having to qualify L2CAP enhanced credit based flow control.
The L2CAP/LE/REJ/BI-02-C conformance test will fail when enhanced CBFC
has not been selected in the ICS.
The lower tester expects that since the Enhanced CBFC is not supported,
the command L2CAP_CREDIT_BASED_CONNECTION_REQ should be met with an
L2CAP_COMMAND_REJECT_RSP and not an L2CAP_CREDIT_BASED_CONNECTION_RSP.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Added a feature that allows an application to request
automatic discovery of the CCCD handle when subscriping
to a characteristic. In order to preserver RAM, the application
is expected to provide the discovery parameters, and it's up
to the application whether or not it wants to reuse the
discovery parameters or use one for each characteristic.
Signed-off-by: Emil Gydesen <emil_gydesen@bose.com>
Turn the GATT notify multiple feature off as default value.
This feature changes the behavior of the bt_gatt_notify API in a way
that might not be backwards-compatible.
This is because the notify multiple header is larger, and therefore
limits the amount of bytes that could otherwise have been sent in a
normal notify PDU for a given ATT MTU.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This adds support for ATT_MULTIPLE_HANDLE_VALUE_NTF,
ATT_READ_MULTIPLE_VARIABLE_REQ and ATT_READ_MULTIPLE_VARIABLE_RSP.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for EATT bearer which was introduced in 5.2, they work
as extra channels to have GATT traffic, at the moment it is completely
transparent to application when they are in use since the allocation
happens automatically.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This should reduce the footprint on applications that do a lot of
requests i.e have a lot of subscriptions.
Fixes#21103
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Also replace some
config
prompt "foo"
bool/int
with the more common shorthand
config
bool/int "foo"
See the 'Style recommendations and shorthands' section in
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The Service Changed characteristic support should also work when the
GATT database has been modified after reboot (firmware update scenario)
This commit introduces a BT_GATT_SERVICE_CHANGED config option that is
independent from BT_GATT_CACHING and BT_GATT_DYNAMIC_DB.
Signed-off-by: François Delawarde <fnde@oticon.com>
subsys/bluetooth/host/Kconfig.gatt is already sourced within an
'if BT_CONN' in subsys/bluetooth/host/Kconfig.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Disable flow control with POSIX_ARCH since these boards tend to run
faster than normal defering the TX callback to system wq may not be
able to run before another packet is received.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Jonathan Rico