Add devicetree binding for the PSA Crypto Random source.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
This commit adds missing binding file for the ite,it8xxx2-usbpd.
Without this file, the DT_HAS_*_ENABLED macro wasn't defined and
couldn't be used in the Kconfigs.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
A USB TypeC connector has many peripherals associated with
it and the DTS binding in this commit provides a way to group
peripherals and properties in a device tree.
This binding is used with the USB-C Subsytem.
This is based on Linux, documentation:
https://www.kernel.org/doc/Documentation/devicetree/bindings/connector/usb-connector.yaml
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
Add pin control properties to the STM32 UCPD bindings file so that
the pins can be configured in the device tree.
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
Executing code out of RAM on IT8xxx2 requires that the relevant
addresses be mapped onto the CPU's instruction memory bus, referred to
by ITE documentation as Instruction Local Memory (ILM). ILM mappings
configure blocks of RAM to be used for accesses to chosen addresses when
performing instruction fetch, instead of the memory that would normally
be accessed at that address.
ILM must be used for some chip features (particularly Flash
self-programming, to execute from RAM while writing to Flash), and has
historically been configured in the Flash driver. The RAM for that was
hard-coded as a single 4k block in the linker script. Configuring ILM
in the flash driver is confusing because it is used by other SoC code as
well, currently in code that cannot depend on the Flash being functional
or in hand-selected functions that seem performance-critical.
This change moves ILM configuration to a new driver and dynamically
allocates RAM to ILM in the linker script, allowing software use of the
entire 64k RAM depending on configuration. This makes ILM configuration
more discoverable and makes it much easier to correctly support the
CODE_DATA_RELOCATION feature on this SoC.
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
USB interface that may be used to send messages from a USB host to
the M4 processor in the S3B, and vice-versa.
Signed-off-by: Michal Sieron <msieron@antmicro.com>
Add support for regulator-boot-on to PMIC driver. Many PMIC devices will
be enabled at boot, so this property allows the regulator framework
to correctly track their state.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
As part of a previous refactor, this property was removed from the STM32
USART binding. The driver code to support this feature was not changed.
This commit simply adds the property back to the new base .yaml for
device trees which used it.
Tested on a proprietary board using the STM32U5 on USART1.
Signed-off-by: Peter Maxwell Warasila <madmaxwell@soundcomesout.com>
Migrates all Winsen sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all WE sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Vishay sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all TI sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all ST sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Silabs sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Sensirion sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Semtech sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Seeed sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all SBS sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Plantower sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Panasonic sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all NXP sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Nuvoton sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Nordic sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Microchip sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Measurement Specialties sensors to inherit base sensor
device properties. This will allow us to define properties shared by
multiple sensors in one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Maxim sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all LM sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all ITE sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Intersil sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Invensense sensors to inherit base sensor device
properties. This will allow us to define properties shared by multiple
sensors in one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Infineon sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all HOPERF sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Honeywell sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Espressif sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Bosch sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Avago sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Atmel sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Asahi-Kasei sensors to inherit base sensor device
properties. This will allow us to define properties shared by multiple
sensors in one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Aosong sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all AMS sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all ADI sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Introduces an initial set of devicetree properties to be inherited by
all sensor devices, similar to how we define a base set of devicetree
properties for I2C and SPI devices. These properties will be used by the
future sensor subsystem to manage and expose sensors to a host operating
system, through HID or another protocol. Additional properties may be
added in the future.
An earlier version of this patch attempted to use the label property
instead of friendly-name, as it was noted during code review as a
possibly legitimate usage of the mostly-deprecated label property.
However, in practice it was difficult to implement because most sensor
bindings also inherit from i2c-device.yaml or spi-device.yaml, and
therefore inherit the deprecated label property from base.yaml. To work
around the deprecation, every sensor binding would have needed to
explicitly block the label property with a property-blocklist, which
would somewhat defeat the purpose of having a shared sensor-device.yaml.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Add MEC172x full duplex qmspi driver version to support full
duplex transfers as expected by the Zephyr spi driver model.
On every spi clock we transmit one bit and receive one bit.
This driver will work with Zephyr SPI NOR driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
updated dts variables naming (hyphen instead of underscore).
moved all properties in microchip ldma yaml to a separate include file,
these properties will be common with the (to be added)
full duplex spi driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Neil Armstrong