Share lis2dh driver among few accelerometer sensors that has
same register interface: LIS2DH, LIS3DH, LSM303DLHC, LIS2DH12,
LSM303AGR.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add support to STM LIS2DS12 3-axis accelerometer driver.
The driver support I2C and SPI bus communication and both
polling and drdy trigger mode.
Currently it uses high resolution only as power mode.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Driver fxos8700 can also be used for the MMA8451
accelerometer and offers more functionality.
Revert the commit to avoid duplicate code.
This reverts commit 9c0d7813e5.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Added support to LIS2MDL Magnetometer sensor provided
with following features:
- I2C interface
- Mag data
- Temperature data
- ODR configurable by config or at runtime
- Trigger mode selectable by menuconfig
- IRQ pin configurable (by dts or Kconfig)
- Hard Iron offset setting at runtime
- Include yaml file
Tested on ST MEMS IKS01A2 + NUCLEO STM32F411RE board.
LIS2MDL connected to I2C master interface (SPI 3 wire not
supported yet).
Test run with all ODR {10, 20, 50, 100} Hz in poll and
trigger mode.
GPIO IRQ dts configuration has been tested by adding
to boards/arm/nucleo_f411re/nucleo_f411re.dts file
this patch:
&i2c1 {
status = "ok";
clock-frequency = <I2C_BITRATE_FAST>;
+
+ /* ST Microelectronics LIS2MDL mag sensor */
+ lis2mdl-magn@1e {
+ compatible = "st,lis2mdl-magn";
+ reg = <0x1e>;
+ irq-gpios = <&gpioa 4 0>;
+ label = "LIS2MDL";
+ status = "ok";
+ };
};
and adding boards/arm/nucleo_f411re/dts.fixup with following
content:
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_LABEL
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_BASE_ADDRESS
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_BUS_NAME
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_IRQ_GPIOS_CONTROLLER
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_IRQ_GPIOS_PIN
For more info on this LIS2MDL please follow this link:
http://www.st.com/en/mems-and-sensors/lis2mdl.html
Signed-off-by: Mario Tesi <mario.tesi@st.com>
The bmm150 sensor driver was missed in the conversion from kbuild to
cmake. This problem was found when updating the build_all tests to
include missing sensor drivers.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds support for the Analog Devices ADXL372 ultra-low power,
3-axis, +/-200 g MEMS accelerometer. The ADXL372 can be either connected
via a SPI or I2C interface.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Only basic features supported initially but more could be added from:
https://www.nxp.com/docs/en/data-sheet/MMA8451Q.pdffixes#9006
A sample app will be provided in a separate PR.
Signed-off-by: Lars Knudsen <larsgk@gmail.com>
This patch adds support for the Analog Devices ADT7420 High-Accuracy
16-bit Digital I2C Temperature Sensors. Optionally sensor threshold
events are supported.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Normally a syscall would check the current privilege level and then
decide to go to _impl_<syscall> directly or go through a
_handler_<syscall>.
__ZEPHYR_SUPERVISOR__ is a compiler optimization flag which will
make all the system calls from the driver files directly link
to the _impl_<syscall>. Thereby reducing the overhead of checking the
privileges.
In the previous implementation all the source files would be compiled
by zephyr_source() rule. This means that zephyr_* is a catchall CMake
library for source files that can be built purely with the include
paths, defines, and other compiler flags that all zephyr source
files uses. This states that adding one extra compiler flag for only
one complete directory would fail.
This limitation can be overcome by using zephyr_libray* APIs. This
creates a library for the required directories and it also supports
directory level properties.
Hence we use zephyr_library* to create a new library with
macro _ZEPHYR_SUPERVISOR_ for the optimization.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Add support for AMS CCS811 Digital Gas Sensor for monitoring
indoor air quality. This sensor reports the following parameters:
1. Co2 concentration
2. VOC concentration
3. Sensor voltage
4. Sensor current
This driver only supports polling mode as of now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add driver for ST vl53l0x time of flight sensor.
This driver can be used in 2 modes :
* proximity sensor :
configure VL53L0X_PROXIMITY_THRESHOLD
will return 1 if target is between sensor and threshold,
else, 0
* distance sensor :
will return the distance in millimeters from sensor to target
This driver use the official STMicroelectronics library for vl53l0x.
(in ext/hal/st/lib/sensor/vl53l0x)
Signed-off-by: Vincent Veron <vincent.veron@st.com>
This patch adds the driver for Panasonic AMG88xx
infrared array sensor.
The driver was developed within the framework of a student
internship in the development department. The task of the
student was to implement the trigger part of the driver,
transfer and visualization of the measured data.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Armando Visconti