Enable HW PWM driver instead of the SW one on nRF SoCs where the PWM
peripheral is present.
Default PWM instances are also enabled on Nordic DK boards so that it
is possible to build the basic fade_led sample for them without extra
adjustments.
After the above changes are applied, some configuration alterations
in basic samples blink_led and fade_led become no longer needed.
These are removed. And the blink_led sample is corrected so that it
works with the nRF HW PWM driver as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Some defines should have been converted from CONFIG_ to DT_ prefix. For
some reason they got missed in this driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Correct it so that it is possible to use PWMs on nRF9160 as well,
not only on nRF5 family SoCs.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Modified drivers to use DEVICE_AND_API_INIT() instead of DEVICE_INIT()
This will make sure driver_api,is populated at build time and is exposed
to user space
Signed-off-by: Varun Sharma <varun.sharma@intel.com>
Check clock_control_on return value now that it is checking appropriate
bus is used in the request.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The channels assigned to the controller are reordered so that the ones
previously used and now available for other purposes have continuous
numbers. When the controller can take advantage of the pre-programmed
PPI channels (when TIMER0 is used as the event timer), the now free
channels are 0-4, when it cannot, it is the channel 0.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Consistently use
config FOO
bool/int/hex/string "Prompt text"
instead of
config FOO
bool/int/hex/string
prompt "Prompt text"
(...and a bunch of other variations that e.g. swapped the order of the
type and the 'prompt', or put other properties between them).
The shorthand is fully equivalent to using 'prompt'. It saves lines and
avoids tricking people into thinking there is some semantic difference.
Most of the grunt work was done by a modified version of
https://unix.stackexchange.com/questions/26284/how-can-i-use-sed-to-replace-a-multi-line-string/26290#26290, but some
of the rarer variations had to be converted manually.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
When the PWM_NRFX Kconfig option is enabled, add the nrfx driver
to the build automatically by selecting the NRFX_PWM option (it is
a hidden one, so the user cannot do it manually via menuconfig).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Adds a translation layer to make the nrfx driver for nrf52 PWM
peripheral accessible via the Zephyr's API.
Signed-off-by: Justin DeMartino <jdemarti@gmail.com>
Add support for specifying the clock prescaler value for the HF timer
used for generating the PWM signals. This allows for lower timer
frequency and thus slower PWM signals (e.g. for use as servo
controller).
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
The nRF5x HF timer base frequency is 16 MHz, not 16777216 Hz.
The improved accurracy of the PWM signal was verified with an
oscilloscope on a BBC micro:bit.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add fixup info for PWM nodes on STM32F0/F1/F3/F4/L4 and remove the
conflicting Kconfig symbols to fully switch STM32 PWM to device tree.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
CONFIG_CLOCK_STM32_APB2_PRESCALER does not exist for STM32F0 as it was
removed from the RCC Kconfig by commit d0678201c3 ("drivers:
clock_control: provide support for stm32f0."). This will break the PWM
driver if compiled for STM32F0.
Conditionally disable usage of this symbol for STM32F0 as all PWMs are
on APB1 for this family.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
PWM1 / PWM15 / PWM16 and PWM17 on STM32F0 do not use the same clocks
compared to the other series.
Add the STM32F0-specific clocks where needed.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
Not all PWM clocks belong to the GRP1, for example TIM1 on STM32F0. Add
the group information to the macro to enable supporting these PWMs in
the future.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
The prescalers are currently hardcoded and are not user-selectable. As a
result, the frequency of the timer can be inadequate to the task. For
instance, the frequency of the 16-bit timers (prescaler 10000) is
usually too low to correctly generate of PWM of a few kilohertz.
Hardcoded prescalers are replaced by Kconfigs so the user can choose at
compile time. The default value of each Kconfig matches the hardcoded
prescaler, so the change will be transparent.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
All the PWM between 1 and 20 can be found on the STM32 depending on the
serie and the specific model. Add all the missing PWMs up to PWM20 to
plan for the future needs.
Tested on STM32L496 with available PWMs.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
The registration of each PWM differs only by a few details.
These differences can be factorized in order to create a generic
registration macro.
This has several advantages:
- Less code
- Easier to add new PWM
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
The various macros to do checks in system call handlers all
implictly would generate a kernel oops if a check failed.
This is undesirable for a few reasons:
* System call handlers that acquire resources in the handler
have no good recourse for cleanup if a check fails.
* In some cases we may want to propagate a return value back
to the caller instead of just killing the calling thread,
even though the base API doesn't do these checks.
These macros now all return a value, if nonzero is returned
the check failed. K_OOPS() now wraps these calls to generate
a kernel oops.
At the moment, the policy for all APIs has not changed. They
still all oops upon a failed check/
The macros now use the Z_ notation for private APIs.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
TimerHandle->Init.Period is used to initialize TIMx ARR register. The
timer will count from 0 up to ARR including, thus it will tick
(ARR + 1) timers per period. As the "period_cycles" variable holds the
number of desired ticks, the ARR register is computed as
ARR = period_cycles - 1
Update the code to reflect this relationship. Otherwise the timer will
count one more tick for each period, leading to a wrong PWM frequency.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
When we called DEVICE_AND_API_INIT for PMW3, we accidently had
pwm_stm32_2 instead of pwm_stm32_3.
Fixes: #6625
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Normally a syscall would check the current privilege level and then
decide to go to _impl_<syscall> directly or go through a
_handler_<syscall>.
__ZEPHYR_SUPERVISOR__ is a compiler optimization flag which will
make all the system calls from the driver files directly link
to the _impl_<syscall>. Thereby reducing the overhead of checking the
privileges.
In the previous implementation all the source files would be compiled
by zephyr_source() rule. This means that zephyr_* is a catchall CMake
library for source files that can be built purely with the include
paths, defines, and other compiler flags that all zephyr source
files uses. This states that adding one extra compiler flag for only
one complete directory would fail.
This limitation can be overcome by using zephyr_libray* APIs. This
creates a library for the required directories and it also supports
directory level properties.
Hence we use zephyr_library* to create a new library with
macro _ZEPHYR_SUPERVISOR_ for the optimization.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Driver APIs might not implement all operations, making it possible for
a user thread to get the kernel to execute a function at 0x00000000.
Perform runtime checks in all the driver handlers, checking if they're
capable of performing the requested operation.
Fixes#6907.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Upcoming Nordic ICs that share many of the peripherals and architecture
with the currently supported nRF5x ones are no longer part of the nRF5
family. In order to accomodate that, rename the SoC family from nrf5 to
nrf, so that it can contain all of the members of the wider Nordic
family.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fix Kconfig help sections and add spacing to be consistent across all
Kconfig file. In a previous run we missed a few.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The default PWM polarity was 'inversed', which is not aligned with the
other PWM drivers. Unfortunately there is not yet an API to define the
default polarity to be used by the driver, but assume that 'normal'
(signal starts high for the duration of the duty cycle) should be the
default.
Signed-off-by: Ricardo Salveti <ricardo@opensourcefoundries.com>
Use "select USE_STM32_HAL_TIM" to select the needed STM32 HAL files,
instead of editing ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
As the nRF5x BLE controller uses TIMER1, TIMER2 and PPI
indices 0-13 (and 14-15, if PA/LNA feature is enabled),
the software based PWM driver needing 6 PPI channels has
to use PPI indices outside the BLE controller used range.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
SoCs outside the Kinetis family can have the FTM module, so move the
HAS_FTM config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Note that 'select HAS_FTM' was previously missing from Kconfig.soc and
is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
RCC_HCLK_DIV1 translates to 0x0 while apb_psc uses the value defined
by CONFIG_CLOCK_STM32_APB1/2_PRESCALER (range from 1 to 16).
Manually check if the defined prescaler is 1 or not and use that to
calculate the correct timer clock.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Add support for TIM3 as it is widely available and pins available via
headers on several devices.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Andrzej Głąbek