at91sam3 supposed to go to Sleep mode and stop the CPU clock
(HCLK). It leads to JTAG problems. In order to be able to use
JTAG, we need to keep CPU clock on. This is achieved by
switching to Wait mode and keeping external main clock.
Since Wait mode switches off automatically Fast RC Oscillator,
but keeps external clock untouched.
Change-Id: Ife37a7691c3cbdf434e560725a71d419adafe054
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
There are two major issues with the kconfig:
() Some of the config options have incorrect dependencies inside help
under menuconfig. For example, CONFIG_GPIO depends on BOARD_GALILEO.
() Since the SoC and board specific kconfig files are parsed first,
the help screen would say, for example, CONFIG_SPI is defined at
arch/arm/soc/fsl_frdm_k64f/Kconfig. This is incorrect because
the actual config is defined in drivers/spi/Kconfig.
These cause great confusion to users of menuconfig/xconfig.
To fix these, the SoC and board defaults are now to be parsed last.
Note that the position swapping of defaults in this patch is due to
the fact the the default parsed last will be used.
And, spi_test is broken due to the fact that it requires
CONFIG_SPI_INTEL_PORT_1, but never enables it anywhere. This is
bypassed for now.
Origin: refactored and edited from existing files
Change-Id: I2a4b1ae5be4d27e68c960aa47d91ef350f2d500f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The peripherals utilizing UART were required to register their own
ISR rountines. This means that all those peripherals drivers need
to know which IRQ line is attached to a UART controller, and all
the other config values required to register a ISR. This causes
scalibility issue as every board and peripherals have to define
those values.
Another reason for this patch is to support virtual serial ports.
Virtual serial ports do not have physical interrupt lines to
attach, and thus would not work.
This patch adds a simple callback mechanism, which calls a function
when UART interrupts are triggered. The low level plumbing still needs
to be done by the peripheral drivers, as these drivers may need to
access low level capability of UART to function correctly. This simply
moves the interrupt setup into the UART drivers themselves. By doing
this, the peripheral drivers do not need to know all the config values
to properly setup the interrupts and attaching the ISR. One drawback
is that this adds to the interrupt latency.
Note that this patch breaks backward compatibility in terms of
setting up interrupt for UART controller. How to use UART is still
the same.
This also addresses the following issues:
() UART driver for Atmel SAM3 currently does not support interrupts.
So remove the code from vector table. This will be updated when
there is interrupt support for the driver.
() Corrected some config options for Stellaris UART driver.
This was tested with samples/shell on Arduino 101, and on QEMU
(Cortex-M3 and x86).
Origin: original code
Change-Id: Ib4593d8ccd711f4e97d388c7293205d213be1aec
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Adds the driver to utilize the I2C/TWI interface on Atmel SAM3
family processors for I2C communication.
Note that this currently only supports master mode. Limited
testing has been done using the Fujitsu FRAM sample app.
Change-Id: Ibdb8277e47dd9450b49a66a95421eb1ffb1c4eb4
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The default Kconfig option is missing a condition for the SRAM
base address on SAM3X8E. Add it back so the correct default
can be used.
Change-Id: Ib4103366f693648c76630cbbd71ca98109381d5c
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The PIO controllers on Atmel SAM3 family processors can be
used for GPIOs, so this is the driver.
Change-Id: I3d5712f3a0a71025b820ca1c08dd767ee1e136d8
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds driver for the UART controller on Atmel SAM3X8E.
This UART controller only has two wires for RX and TX, and
does not have flow control (e.g. CTS, RTS) or FIFO.
Currently, the driver does not support any interrupt driven
operations.
Change-Id: I63720bccfb70a89888353b8ee3dfc4b80793dc01
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds initial support for Atmel SAM3X8E processor, which is
based on ARM Cortex-M3. The SAM3X8E is being used on Arduino Due.
Change-Id: I199efcf29629f9ebacad474e5edc91bc3757f613
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Dmitriy Korovkin