Clean up & rework JTAG documentation for ESP-32 boards to provide full
commands and clarify gotchas.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This requires openocd version 0.10 or later.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@linaro.org>
The EFM32 Wonder Gecko Starter Kit contains sensors and
peripherals demonstarting the usage of the EFM32WG MCU
family. This patch add basic support for this board.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Supports both master and slave mode, standard and fast modes,
configurable timeouts, and a few other tunable settings.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
ESP-IDF is in constant development and it's likely that files Zephyr
depends on will be moved, removed, or renamed. Make a note that an
older version of ESP-IDF should be used instead.
Closes#1538.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Instead of having a board-specific config for this adc test, enable the
required battery-sense circuit by default at the board level when the
adc driver is enabled.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Some our Zephyr tools don't like seeing UTF-8 characters, as reported in
issue #4131) so a quick scan and replace for UTF-8 characters in .rst,
.h, and Kconfig files using "file --mime-encoding" (excluding the /ext
folders) finds these files to tweak.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Move all QEMU related defines to the boards and cleanup xtensa platforms
which were marked to be QEMU capable by mistake.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
xtensa uses more stack than other arches, enable the sentinel since we
don't currently have HW-assisted stack checking on this arch.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Default configuration for USART1 (Console output) on board
stm32f3_disco was set on PA9/PA10, which matches Rev-A/B
configuration. Though, on more recent configuration of the
board (Rev-C onward). USART1 is mapped to PC4/PC5.
This configuration has the benefit to support VCP, hence it
is chosen to be set by default.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enable BlueNRJ chip on disco_l475_iot1 board.
Communication with SoC, is done over SPI(3). Hence this
commit enables SPI3 on SoC and configure BT_SPI IRQ,
RESET and CS pins.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add board configuration, dts and pinmux based on both
stm32f469i_disco board and nucleo_f412zg board
Signed-off-by: Massimiliano Cialdi <massimiliano.cialdi@powersoft.it>
Move all STM32 based board pinmux files into the board dirs so we are
consistent across all the STM32 platforms/boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added some clarification on flashing instructions for CC3220SF, in
support of customer issue.
Jira: ZEP-2581
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The zedboard_pulpino has a small amount of flash so we should have that
in the yaml for any tests thats might filter on code size footprint.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
patch add device tree support for develoement board of
quark_se_c1000. Previously pushed patch was flashing binary
at wrong address because of which UART was not working
Jira:ZEP-2459
test
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
BLE is the only networking interface on 96b_carbon, so if
CONFIG_NETWORKING is set, automatically use 6lowpan/BLE link
layer. This will allow to make networking apps work "out of the
box" on 96b_carbon, similar to e.g. qemu_x86 (which automatically
uses SLIP) or frdm_k64f (which automatically uses Ethernet).
This also enables NET_L2_BT_ZEP1656, because most 6LoWPAN/BLE samples
in Zephyr currently use that option, and it is required to achieve
working 6LoWPAN/BLE with Linux kernels currently widely accessible
to the end users. E.g. the latest Ubuntu LTS release, 16.04, ships
with 4.4 kernel, and can be upgraded with a special effort to HWE
kernel which is currently at 4.10. NET_L2_BT_ZEP1656 is needed for
both these kernels.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This reverts commit e1382cc7d6.
Due to restrictive simplelink host driver source licensing.
This also reverts commits based on the simplelink wifi host
driver:
Revert "ext: simplelink: host driver: depend on multithreading"
commit: 4d912b004b
Revert "ext: simplelink: Enable SimpleLink to use Zephyr __errno"
commit: 4e022f7b28
Revert "ext: simplelink: Add SimpleLink DPL porting layer to Zephyr"
commit: 4bc51e67d4
Revert "ext: simplelink: Enable build of the SimpleLink host driver."
commit: 2d2615a49a
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
* add arc mpu driver
* modify the corresponding kconfig and kbuild
* currently only em_starterkit 2.2's em7d configuration
has mpu feature (mpu version 2)
* as the minimum region size of arc mpu version 2 is 2048 bytes and
region size should be power of 2, the stack size of threads
(including main thread and idle thread) should be at least
2048 bytes and power of 2
* for mpu stack guard feature, a stack guard region of 2048 bytes
is generated. This brings more memory footprint
* For arc mpu version 3, the minimum region size is 32 bytes.
* the codes are tested by the mpu_stack_guard_test and stackprot
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add cross-referenced information on the 96b_carbon and
96b_carbon_nrf51 pages which disambiguates between the two "boards".
Also describe how to flash 96b_carbon_nrf51 with
samples/bluetooth/hci_spi and 96b_carbon with samples/bluetooth/ipsp
to support a Bluetooth HCI stack on 96Boards Carbon (the physical
board).
While we're here, make the documentation page for 96b_carbon match the
format in doc/templates/board.tmpl.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
On 96Boards Carbon, Bluetooth is provided by a secondary nRF51 chip
connected to SPI_1, so enable this peripheral and its driver when BT
is selected.
Similarly, provide BT_SPI_* configs to integrate with the BT HCI SPI
driver. The files these config values apply to only get built when
CONFIG_BT=y, but this configuration can't be handled in the "if BT"
section in 96b_carbon's Kconfig.defconfig. This is because BT_SPI is
a choice value, and thus doesn't support a default setting.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Per ZEP-1958, Phase 2 of adding CC3220sf LaunchXL support,
was to "deprecate the CC3200 launchxl support in Zephyr
(redundant to the CC3220)."
Effectively, the CC3220 SOC replaces the CC3200.
This patch removes the following:
* the imported CC3200 SDK
* CC3200 SOC, board, DTS files.
* adjusts other files where cc3200 was mentioned.
Also, it fixes explicit references to CC3200 in generic
CC32xx driver files.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Rename the BT_CONTROLLER prefix used in all of the Kconfig variables
related to the Bluetooth controller to BT_CTLR.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Some boards had HAS_DTS in the defconfig which is dropped if the Kconfig
variable does not have a prompt.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The SimpleLink host driver comes with its own definition of
__errno, which conflicts with Zephyr's definition, but has
a mechanism to enable use of the porting OS's __errno variable.
This patch enables SimpleLink to use Zephyr's __errno
via the DPL porting layer.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
This patch enables and builds the SimpleLink host driver
for Zephyr introduced in a previous patch.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Andy Ross