Enables instance 3 of the lpuart driver, adds dts fixups, and configures
pinmuxes to use bluetooth hci on the mimxrt1050_evk board. Updates board
documentation accordingly.
Tested with samples/bluetooth/peripheral_hr, with frdm_kw41z attached as
an arduino shield running the nxp hci controller application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The i2c drivers now consistently select HAS_DTS_I2C, so we no longer
need to select it at the board level.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add board support files for mimxrt1060_evk, the development board for
i.MXRT1062 (CM7) SoC.
- Add pinmux, dts, doc.
- External QSPI flash hasn't been configured yet. So code can be loaded
to SRAM for now.
- Tested samples: hello_world, philosophers, synchronization,
basic/blinky, and basic/button.
Signed-off-by: Ryan QIAN <jianghao.qian@nxp.com>
The i2c_slave_api test was not getting executed on the nucleo_f091rc
board due to a missing supported features list.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Cleanup unused leftover from shield development.
These flags are not actually useful, nor used as dts connectors
are sufficient to control board to shield binding is
operational and dtc provides meaningful error message
when this is not the case.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This change aims at fixing 'unit_address_vs_reg' warning in
STM32 based boards.
This warning pops up when a node name is made up with an address
(node_name@xx) but does not contain a reg property.
This case was encountered for led nodes for instance,
where a reg property has no meaning.
Fix this by changing node_name@xx to node_name_xx which removes the
guilty '@xx' syntax but preserves node_name uniqueness.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The nrf52840_pca10056 defconfig apparently started off as a copy of the
one for nrf52840_pca10040 and one comment was forgotten to be adapted
accordingly.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
This patch adds support of the SAMD21 XPlained board. The board has a
similar pinout to the SAMD20 XPlained with a different pin-mapping.
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
In dts.cmake, build shield list. For each shield, check if
associate KCONFIG is enabled and if it is, add matching files
to following new cmake variables:
-DTC_SHIELD_OVERLAY_FILE
-DTC_SHIELD_FIXUP
Then, consume these variables when needed.
Shield overlay is conceived as the very first overlay applied
to the board dts. It intends to build a new board that should
then behave as any other board versus common or user's overlay.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Added cy8ckit_062_wifi_bt_m4 board configuration to build FW for CM4
core.
CM4 core does not start itself, it have to be started by CM0+ FW.
Signed-off-by: Nazar Chornenkyy <nazar.chornenkyy@cypress.com>
Signed-off-by: Oleg Kapshii <oleg.kapshii@cypress.com>
This patch changes the behavior of the sensor. The sensor
will remain in sleep mode after initialization and will only
run the measurements once when sample_fetch is called.
This optimizes the power consumption of the sensor as it
stays in sleep mode most of the time.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This change aims at fixing 'unit_address_vs_reg' warning in
STM32 based boards.
This warning pops up when a node name is made up with an address
(node_name@xx) but does not contain a reg property.
This case was encountered for button nodes for instance,
where a reg property has no meaning.
Fix this by changing node_name@xx to node_name_xx which removes the
guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enable UART 16550 driver for Nios-II QEMU platform.
Note: This PR is tested with patched version Qemu 3.0.0 which
adds support for altera_10m50_zephyr machine type.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
This commit removes all MPU-related (ARM_CORE_MPU and NXP_MPU)
options exept ARM_MPU, which becomes master switch controlling
MPU support on ARM.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The HAS_SYSMPU option is just selecting NXP_MPU option,
which could be also controlled through menuconfig.
This commit removes the HAS_SYSMPU option and replaces
its usage by NXP_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The ARM_MPU_IMX_RT option is just selecting ARM_MPU option,
which could be also controlled through menuconfig.
This commit removes the ARM_MPU_IMX_RT option and replaces
its usage by ARM_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The ARM_MPU_NRF52X option is just selecting ARM_MPU option,
which could be also controlled through menuconfig.
This commit removes the ARM_MPU_NRF52X option and replaces
its usage by ARM_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The ARM_MPU_ENABLE option is just selecting ARM_MPU option,
which could be also controlled through menuconfig.
This commit removes the ARM_MPU_ENABLE option and replaces
its usage by ARM_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The STM32_ARM_MPU_ENABLE option is just selecting ARM_MPU option,
which could be also controlled through menuconfig.
This commit removes the STM32_ARM_MPU_ENABLE option and replaces
its usage by ARM_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
Sets the HPET timer frequency (enabled by default) to 19.2MHz.
And also sets the local APIC timer frequencies according to
the SoC variant.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There are currently three SoC variants for the UP Squared board:
Pentium, Celeron and Atom. This adds a board option to specify
for which variant is being built.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Enables an instance of the lpspi peripheral, configures the pinmuxes,
and updates the board documentation accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
We get the following warning when building nrf52810_pca10040:
Warning (avoid_unnecessary_addr_size): unnecessary
#address-cells/#size-cells without "ranges" or child
"reg" property in /buttons
Remove #address-cells/#size-cells since they aren't needed for gpio_keys
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When we fixed the missing reg property in the cpu node, we forgot to
add #address-cells & #size-cells for the node.
This fix the following warnings we get:
Warning (reg_format): "reg" property in /cpus/cpu@0 has invalid
length (4 bytes) (#address-cells == 2, #size-cells == 1)
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get the following warning when building nrf52810_pca10040:
Warning (avoid_unnecessary_addr_size): unnecessary
#address-cells/#size-cells without "ranges" or child
"reg" property in /gpio_keys
Remove #address-cells/#size-cells since they aren't needed for gpio_keys
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /flash: node has a reg or ranges
property, but no unit name
or
Warning (unit_address_vs_reg): /memory: node has a reg or ranges
property, but no unit name
Fix by adding unit address that is missing to flash & memory nodes.
Additionally the Silabs memory nodes didn't have a compatiable or
device_type, so add those properties as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /cpus/cpu@0: node has a
unit name, but no reg property
Fix by adding reg property to missing cpu nodes.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /cpus/arcv2-intc@0:
node has a unit name, but no reg property
Fix by removing the unit address from the nodes. Some cases we had a
reg property and a unit address for such interrupt controllers, in those
cases remove both the reg & unit address in the node name.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /gpio_keys/joystick@0:
node has a unit name, but no reg property
Fix by dropping the unit address and renaming the node names to include
more information about the gpio_key.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (alias_paths): /aliases: aliases property name
must include only lowercase and '-'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enable native logger backend for native_posix board in defconfig.
Set also logger configuration options suitable for native_posix
backend.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
For native_posix:
Added command line options to control if traces should have
or not colors.
+
Detect if we are connected to a tty or not, and if we are
set the defaults for that option appropriately
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Update all supported features and peripherals in the official set of
boards from Nordic Semiconductor.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_NRF51822_QFAA
CONFIG_SOC_NRF51822_QFAB
CONFIG_SOC_NRF51822_QFAC
CONFIG_SOC_NRF52810_QFAA
CONFIG_SOC_NRF52832_QFAA
CONFIG_SOC_NRF52832_CIAA
CONFIG_SOC_NRF52832_QFAB
CONFIG_SOC_NRF52840_QIAA
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_PART_NUMBER_SAME70*
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we have a common DT_SIZE_K macro use it instead of defining
__SIZE_K eveywhere. We also have DT_SIZE_M, so use that in a few
places as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_PART_NUMBER_EFM32WG990F256
CONFIG_SOC_PART_NUMBER_EFR32FG1P133F256GM48
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_CC3220SF
CONFIG_SOC_MSP432P401R
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the SoC outside of the architecture tree and put them at the same
level as boards and architectures allowing both SoCs and boards to be
maintained outside the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Maureen Helm