Migrate from "legacy" PCI support (drivers/pci) to new PCI(e) support.
The e1000 driver is merely for testing with QEMU and so should not be
a model for the use of PCI(e) functions. Consult instead "real-world"
PCI(e) drivers like the NS16550 UART (drivers/serial/uart_ns16550.c).
Signed-off-by: Charles Youse <charles.youse@intel.com>
Remove magic numbers from Ethernet drivers and tests by defining
NET_ETH_MAX_DATAGRAM_SIZE and NET_ETH_MAX_FRAME_SIZE.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Use the new API where relevant. Only sam_gmac is left aside for now.
This simplifies a lot the code as the caller should only care about
allocating net_pkt and its buffer once, and thus will not need to mess
with "frags" etc...
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There is no need to reserve any space for each frag, as the l2 will
allocate a frag for the ethernet header, arp will do the same.
This is one step further to removing the concept of ll reserve.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Update such statistic on all drivers.
Also, remove TX stats in native and stellaris drivers: such update is
done in L2 now.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now instead of such path:
net_if_send_data -> L2's send -> net_if tx_queue -> net_if_tx -> driver
net_if's send
It will be:
net_if_send_data -> net_if tx_queue -> net_if_tx -> L2's send -> driver
net_if's send
Only Ethernet is adapted, but 15.4 and bt will follow up.
All Ethernet drivers are made compatible with that new scheme also.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The error check was wrong, if we could send the packet then
we free it. If sending fails, then let the caller to decide
what to do with the packet.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add "Multicast Promiscuous Enabled" (RCTL_MPE) bit definition and
use it for the receive control register (RCTL) initialization.
Multicast needs to be enabled in order for IPv6 auto-configuration
to succeed.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
The initial sequence was wrong and led to the missing interrupt
problem with netdev backends where the incoming traffic
appears immediately (tap).
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
This patch adds a driver for Intel PRO/1000 Gigabit Ethernet controller.
The driver currently supports only a single instance of the NIC.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Charles Youse