Use the device tree to assign the correct peripheral clock to each
UART/USART/LEUART. Previously, the clock identifier was determined
through the sequence number of the instantiated UART. This meant
configuring all UARTs when only one of the later UARTs was required.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
The true mmio-sram nodes should not have had a 'device_type' property.
Remove it from the cases that we clearly know are SRAM.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds 'clock-frequency' property to the cpu nodes.
The clock frequency specified in the added property is used
during platform configuration. Examples:
- The SWO logger uses clock frequency to configure SWO output.
- Plenty of platforms need CPU clock specified for their HAL.
- Most of devices with USB needs information about CPU clock
in order to configure USB clock source.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
This commit adds counter driver based on RTCC module for SiLabs Gecko
SoCs.
Tested with SLWSTK6061A / BRD4250B wireless starter kit.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
By default, after reset SWO signal is not connected to GPIO pin.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
By adding 'aliases' node in SoC .dtsi file it is possible to generate
DT_ defines which specify a logical name rather than relay on module
location on APB bus. E.g. DT_SILABS_GECKO_USART_40010000_LABEL becomes
DT_SILABS_GECKO_USART_USART_0_LABEL. Thus it is possible to remove
dts_fixup.h defines.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The Silicon Labs EFM32 Pearl Gecko MCU includes:
* Cortex-M4F core at 40MHz
* up to 1024KB of flash and 256KB of RAM
* multiple low power peripherals
Ported from EFM32WG:
https://www.silabs.com/documents/public/application-notes/an0918.0-efm32_to_efm32jgpg_migration_guide.pdf
Signed-off-by: Gil Benkö <gil.benkoe@pm.me>
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Oane Kingma