The SAM0 SoC was switched to use DTS for SPI configuration. Update
documentation for the SAM0 based boards to use the correct SPI
controller device names.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
As the board has ethernet chip it makes sense to enable the
ethernet support by default.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Upcoming Nordic ICs that share many of the peripherals and architecture
with the currently supported nRF5x ones are no longer part of the nRF5
family. In order to accomodate that, rename the SoC family from nrf5 to
nrf, so that it can contain all of the members of the wider Nordic
family.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
New revision (SWCU117H) got published and the old one (supposedly
SWCU117G) is no longer available.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
This creates zeth network interface in your host and allows user
to send and receive data sent to this network interface.
Fixes#6007
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Currently, it seems that only boards with smaller amount of RAM
get a value for "ram" property, and very few boards have "flash"
defined. However, to test bigger sample applications, it's helpful
to have these properties universally defined.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Added support for Waveshare BLE400 board.
Tested it with the following samples and confirm it work.
- samples/basic/blinky
- samples/basic/button
- samples/basic/fade_led
- samples/basic/threads
Signed-off-by: Roman Tataurov <diytronic@yandex.ru>
Describe in documentation few methods that can be used by
users to flash the ArgonKey with a binary image.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
According to a conversation with @carlescufi and @finikorg, the
zephyr codebase should only use the Linux Foundation USB vendor
ID. The USB vendor IDs and product IDs in the board definitions
are an obsolete leftover from old code and no longer needed.
Signed-off-by: Iván Sánchez Ortega <ivan@sanchezortega.es>
Move the dts.fixup back to board dir in prep for support mps2_an521.
The memory maps between the two mps2_an385 and mps2_an521 differ greatly
so its easier to just keep the fixup files with the board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add initial support for NUCLEO-L073RZ board.
This is a typical Nucleo-64 board, so most files are reused
from already supported Nucleo boards with small changes.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
SoC dts fixups are added and the i2c_nrf5 driver is modified to use
the values generated from the device tree.
The I2C_*_DEFAULT_CFG and I2C_*_IRQ_PRI options are removed from board
defconfigs. Bitrate and IRQ priority are configured using using the
device tree instead.
HAS_DTS_I2C is selected on all nrf5 boards to prevent generation of
conflicting defines from Kconfig.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
The i2c controller nodes are enabled in the board specific dts files
on boards where the controller was enabled in the board Kconfig.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
This commit changes the Arduino Zero pinmux configuration to use PA12
as MISO.
According to the schematic, the Arduino Zero provides a SPI bus on
SERCOM4 with the following pads/pins:
- MISO: PA12/pad0 (pin 21)
- MOSI: PB10/pad2 (pin 19)
- SCK: PB11/pad3 (pin 20)
The MISO signal is incorrectly labeled as PB12_S4_SPI_MISO on the
schematic. It should be labeled PA12_S4_SPI_MISO.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Nucleo-64 boards do not have X3 crystal by default, so HSE is clocked
from MCO output of ST-LINK, and CONFIG_CLOCK_STM32_HSE_BYPASS should be
enabled. STM32F0 HSE somehow magically works even without that, but
to do so is the right thing.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Since not all boards enable all devices, we typically have the SoC dtsi
file have a device marked with status = "disabled" and have the
board.dts explicitly enable with status = "ok". Update it so USB on
Atmel SAMD21 work this way.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move IRQ numbers into device tree so we can remove soc_irq.h. We are
already using IRQ defines generated form the DTS so no point in having
soc_irq.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added device tree support to the ARM SBCon I2C controller. We utilize
the compatiable "arm,versatile-i2c" the binding from Linux for the some
peripheral block.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The legacy SPI API was turned back on for the Adafruit Feather M0
Basic Proto when the SAM0 SoC was switched to using DTS for SPI. This
commit turns it back off.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
ArgonKey board is a 96boards sensor hub platform for all 96Boards
compliant family products. The ArgonKey packs a Cortex-M4 chip
together with a set of motion, environmental and ambiental sensors
and can be used as a development platform for many different
applications.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Switch the SoC device tree to define a single entry per SERCOM instead
of one per mode.
Define a Device Tree binding for the SAM0 SPI and use it instead of
Kconfig for enabling / disabaling instances
Switch the Arduino Zero, Adafruit Feather M0 Basic Proto, and
Trinket M0 to use the new defintion.
Add the APA102 LED that's on the Trinket as a test.
Signed-off-by: Michael Hope <mlhx@google.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Changed the default UART used for the console. You used to have to
use wires on the J4 header. Now you can use the UART provided by the
Segger USB composite device.
Signed-off-by: Justin Watson <jwatson5@gmail.com>
Fixed the output string in the documentation for
the SAM E70 Xplained. The output for the hello_world
sample wasn't correct.
Signed-off-by: Justin Watson <jwatson5@gmail.com>
Support the ST STM32F0DISCOVERY board with STM32F051R8T6 SoC
Tested with:
- `samples/basic/blinky`
- `samples/basic/button`
Includes flash config in `stm32f0_disco.rst` for use with mcuboot
Signed-off-by: Nathan Tsoi <nathan@vertile.com>
The Feather M0 Basic Proto is an Atmel SAMD21 based development board
with USB, UART, SPI, LED and onboard lithium polymer battery charger.
Use of the Adafruit stock photo (adafruit_feather_m0_basic_proto.jpg)
for the board documentation was approved by Adafruit Industries.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
As USB port is present on the board, and pinmux configured,
add USB support in board dts file.
Configure Ethernet oer USB as default net i/f
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Change TICKS_PER_SEC from 1000 to 100
* em_starterkit is a FPGA board with cores running at max 30 Mhz.
1000 ticks per second is a little heavy for it.
* the tests/kernel/common requires 200 ticks per second at most,
or the testcase will stall.
disable the generation of bin file.
* there is no flash in em_starterkit
* there is huge gap between ICCM and DCCM which will cause the bin
file too large, alomst 2GB
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
According to STM32-E407.pdf (Revision I, June 2017), CON1 RST is
connected to processor pin #25, not #23.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Henrik Brix Andersen