Add support for similar adin1100 phy, boath are 10Base-T1L,
only difference is that adin1100 connects through r/mii.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
The MAC address macros are ridiculous in this driver.
Rewrite to be simpler and use eth.h common function.
Also, clarify the mac address generation on the DT overlays.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Remove ethernet-fixed-link binding as it is redundant with the
phy bindings. Clearly, ethernet does not work without the L1
layer, which is a phy device, or an integrated mac/phy device,
and all of these things should be described properly in DT.
The schema did not even come with a compatible, meaning nodelabels
were hardcoded into the drivers, which is unacceptable.
- Remove the binding file for ethernet-fixed-link.yaml.
- Remove fixed link functionality from the nxp s32 gmac driver.
Since this functionality is already covered by the phy support,
it is redundant.
- Remove fixed link include from the s32 gmac binding.
- Remove fixed link include from the nuvoton numaker binding.
As far as I can tell the corresonding driver does not even
use it anyways, and I did not find any board with this device
that describes a "fixed link".
- Move the definition into the nxp,kinetis-ethernet binding
as the eth_mcux driver, which is already being deprecated,
does use this, contain the debt to the legacy driver.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Byte value written to the device's
ERXFCON: ETHERNET RECEIVE FILTER CONTROL REGISTER
Sets the devices receive packet filter, optional. If not set
in device tree previous hard coded value`0xA3` is used.
Uni, multi and broadcast packets with valid CRC are accepted.
Signed-off-by: Dean Sellers <dsellers@evos.com.au>
Add Open Alliance spi protocol support.
Open Alliance is a chunk-based SPI protocol, based on sending
over SPI an ethernet frame divided in smaller chunks, using a
specific 32-bit header for each chunk transferred. All chunks
can be sent or received by a single dma transfer.
Default mode is set to Open Alliance SPI without protection,
since the adin2111 dev. board comes shipped this way.
Tested:
- Open Alliance SPI, no protection (default board shipped)
- Open Alliance SPI, protection
- Generic SPI, no crc
- Generic SPI, with crc8
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
drivers: eth: phy: tja1103: Handle link change
These changes enable -
TJA1103 driver to gracefully handle Link connect or disconnect events
between Ethernet PHY and its link partner and notify it to the
upper network layers
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
Utilize a code spell-checking tool to scan for and correct spelling errors
in all files within the dts/bindings/ethernet, gpio, i2c and
interrupt-controller.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
- PHY can be set up as rmii but still use 25 MHz MDC, add DT property
value for this case
- Fix KSZ8081 driver spamming phy status in debug level logging,
and fix some other state/logging logic
- Fix PHY driver not rescheduling monitor work if first configuration
fails, change code path to use goto for errors
- Handle case where some phys are not using the gpio pins in phy driver
Make GPIO properties of ksz8081 phy optional since these hardware pins
may be unused on some boards
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
In case of boards where REF_CLK signal is not connected
to the GPIO0 by default add the possibility to use
the optional GPIO16/GPIO17 as a REF CLK source.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
Add Driver for KSZ8081 Ethernet PHY. The Generic MII Driver
is not sufficient to use for this PHY chip which has special
vendor implemented behaviors.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add a property to the ethernet controller binding
indicating what type of connection the MAC has with
the PHY device.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Adds the tja1103 enet phy for setting phy options on the mr_canhubk3.
Co-authored-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
This patch set provides support for T1S ethernet device - LAN8651.
For SPI communication the implementation of Open Alliance TC6
specification is used.
The driver implementation focuses mostly on reducing memory footprint,
as the used SoC (STM32G491) for development has only 32 KiB RAM in total.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Updates Ethernet PHY devicetree bindings to be more consistent with
Linux by using the standard `reg` property for the PHY address instead
of a custom `address` property. As a result, MDIO controller bindings
now require standard `#address-cells` and `#size-cells` properties.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Some Ethernet PHYs used the devicetree node name `phy`, while others
used `ethernet-phy`. Be consistent and use `ethernet-phy` throughout.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Now that all in-tree phys are declared under their mdio bus, drop the
`mdio` property and use DT_INST_BUS to find the bus.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add support for ADIN1110 10BASE-T1L Ethernet MAC-PHY.
The ADIN1110 is an ultra low power, single port, 10BASE-T1L
transceiver design for industrial Ethernet applications and is com-
pliant with the IEEE® 802.3cg-2019™ Ethernet standard for long
reach, 10 Mbps single pair Ethernet (SPE). Featuring an integrated
media access control (MAC) interface, the ADIN1110 enables direct
connectivity with a variety of host controllers via a 4-wire serial
peripheral interface (SPI). This SPI enables the use of lower power
processors without an integrated MAC, which provides for the
lowest overall system level power consumption. The SPI can be
configured to use the Open Alliance SPI protocol or a generic SPI
protocol.
Documentation:
https://www.analog.com/en/products/adin1110.html
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Rework the devicetree definition for smsc91x to put the mdio and
ethernet device at the same level, and make the phy a child of the mdio
node.
This allows matching up the device initialization sequence with the
devicetree hierarchy.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add initial support for NXP S32 GMAC/EMAC:
- it's a copy-implementation with DMA data buffers and buffer
descriptors in non-cached memory (buf len and ring size configurable)
- PHY interface selection only implemented for S32K3 devices as it is
SoC-specific
- no PHY driver integration, it works as a fixed link with speed/duplex
configured through devicetree
- supports multicast hash filtering, promiscuous mode, MAC loopback
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Change the eth-phy definition so that the phy is pointed by a phandle
rather than a child node, make the phy device a child of mdio. This
makes more sense from a devicetree hirearchy where the phandles have to
be initialized before the device itself, allows keeping the priorities
in check with CHECK_INIT_PRIORITIES.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Make ethernet phys childs of the mdio device and move the mdio device up
a level on the tree. That makes the device hierarchy coherent with the
required initialization priority and allows keeping the sequence in
check with CHECK_INIT_PRIORITIES.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Rename the phy-dev property with phy-handle to match the Linux
ethernet-controller binding and move it up to ethernet.yaml so that it
can be used by other drivers.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Adds PHY driver. Works via MDIO API and
exposed ADIN2111 MDIO Clause 45
functions.
Link status detection is triggered by
ADIN2111 driver within offloaded IRQ
handler.
Supports:
- LED0, LED1 enable/disable
- Fatal HW error detection
- AN 2.4V tx mode enable/disable
The initialization order is important.
PHY 2 must be initialized after PHY1.
Therefore, it shall be defined after the 1st one
in the devicetree.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds initial ADIN2111 2-Port 10BASE-T1L (SPE)
switch support. Works over SPI.
The driver creates 2 interfaces, 1 per port (PHY).
Configures multicast and broadcast filters.
The same unicast is applied to both ports.
Supports:
- Link state detection
- CRC enable/disable
- Ports config set
- Ports ETH stats
Provides functions for MDIO driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Allows Ethernet communication between "cells"
in the Jailhouse hypervisor.
The vring queue deviates from a standard virtqueue
so is implemented separately.
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
Add the `full-duplex` property for the `microchip,enc28j60` node.
Replace ETH_ENC28J60_0_FULL_DUPLEX Kconfig option with this property.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Arm fvp_baser_aemv8r and fvp_base_revc_2xaemv8a boards are using
SMSC91C111 as their ethernet adapters.
Portions of the codes are based on FreeBSD code from its
'src/sys/dev/smc/if_smc.c' and 'src/sys/dev/smc/if_smcreg.h'.
This driver has two parts, one is the ethernet controller driver, which
is MAC layer driver. The other is the MDIO driver, which is the PHY
layer driver. Both of them are in the same source file due to that they
need to share the same reading and writing register functions and
the smsc object.
The mdio driver is needed by the existing 'phy_mii' driver, which is
a driver for the generic MII-compliant PHY.
This driver was developed under the fvp_base_revc_2xaemv8a target and
has been tested on the fvp_baser_aemv8r target.
Signed-off-by: Huifeng Zhang <Huifeng.Zhang@arm.com>
Bugfix for the Cyclone V SoC DK ethernet driver need to add emac-index
in dts
- We remove the "local-mac-address" property from
dts/arm/intel_socfpga_std.dtsi to
boards/arm/cyclonev_socdk/cyclonev_socdk.dts, since this value is
dependant on the board / implementation and not universal to
the "intel_socfpga" package that it inherets from.
- The above is also true for the "status" property as the board
should enable the device.
Signed-off-by: Benjamin Kyd <benjamin.kyd@intel.com>
Introduce Ethernet low-level driver for NXP S32 Network Controller
(NETC). Current driver allows to manage from Zephyr a Physical Station
Interface (SI) and/or a Virtual SI. The NETC has an integrated Ethernet
Switch. Currently the Switch is initialized from this driver with a
default configuration, and all ports are enabled and transparent for
the user. A separate Switch driver should be addressed in future patches.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Fix all hyphens errors detected by yamllint:
yamllint -f parsable -c .yamllint $( find -regex '.*\.y[a]*ml' ) | \
grep '(comments)'
Default config would be to require two spaces after the start of the
comment, proposing to keep it on 1, inline with the Linux binding
config, that is:
```
- comments:
- min-spaces-from-content: 1
```
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
DTS property attributes are (by default) not required.
Explicitly specifying `required: false` is redundant.
Perhaps a warning to that effect would be useful.
Signed-off-by: Chris Friedt <cfriedt@meta.com>
Use the new PCIe core infrastructure for looking up the BDF at runtime
based on the VID/DID values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Adding ethernet in the DTS file and corresponding binding
for Cyclone V SoC FPGA board..
Signed-off-by: Esteban Valverde <esteban.valverde.vega@intel.com>
Introduce a simple binding for atmel,24mac402 EEPROM that the SAM
GMAC ethernet driver can utilize to get MAC address out of. We
introduce a 'mac-eeprom' phandle into GMAC ethernet devicetree
node that will provide a pointer to the MAC eeprom to utilize.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
This update Atmel sam and sam0 ethernet gmac and mdio drivers to use
pinctrl driver and API. It updates all boards with new pinctrl groups
format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Angelo Dureghello